A novel methodology for virtual qualification of IC packages under board level drop test

2008 ◽  
Author(s):  
Jing-en Luan ◽  
Kim-yong Goh ◽  
Xavier Baraton ◽  
Esa Hussa
Keyword(s):  
Drop Test ◽  
Board Level ◽  
Virtual Qualification

Numerical Model to Simulate the Drop Test of Printed Circuit Board (PCB)

2011 ◽  
Vol 423 ◽  
pp. 26-30
Author(s):  
S. Assif ◽  
M. Agouzoul ◽  
A. El Hami ◽  
O. Bendaou ◽  
Y. Gbati
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Drop Test ◽  
Dynamic Responses ◽  
Circuit Board ◽  
Joint Stress ◽  
Printed Circuit ◽  
Increasing Demand ◽  
Improved Model ◽  
Board Level

Increasing demand for smaller consumer electronic devices with multi-function capabilities has driven the packaging architectures trends for the finer-pitch interconnects, thus increasing chances of their failures. A simulation of the Board Level Drop-Test according to JEDEC (Joint Electron Device Council) is performed to evaluate the solder joint reliability under drop impact test. After good insights to the physics of the problem, the results of the numerical analysis on a simple Euler-Bernoulli beam were validated against analytical analysis. Since the simulation has to be performed on ANSYS Mechanical which is an implicit software, two methods were proposed, the acceleration-input and the displacement-input. The results are the same for both methods. Therefore, the simulation is carried on the real standard model construction of the board package level2. Then a new improved model is proposed to satisfy shape regular element and accuracy. All the models are validated to show excellent first level correlation on the dynamic responses of Printed Circuit Board, and second level correlation on solder joint stress. Then a static model useful for quick design analysis and optimization’s works is proposed and validated. Finally, plasticity behavior is introduced on the solder ball and a non-linear analysis is performed.

Failure Analysis of Halogen-Free Printed Circuit Board Assembly Under Board-Level Drop Test

2012 ◽  
Vol 134 (1) ◽  
Author(s):  
Hung-Jen Chang ◽  
Chau-Jie Zhan ◽  
Tao-Chih Chang ◽  
Jung-Hua Chou
Keyword(s):  
Printed Circuit Board ◽  
Drop Test ◽  
Circuit Board ◽  
Printed Circuit Board Assembly ◽  
Printed Circuit ◽  
Plastic Ball ◽  
Circuit Board Assembly ◽  
Halogen Free ◽  
Board Level ◽  
The Impact

In this study, a lead-free dummy plastic ball grid array component with daisy-chains and Sn4.0Ag0.5Cu Pb-free solder balls was assembled on an halogen-free high density interconnection printed circuit board (PCB) by using Sn1.0Ag0.5Cu solder paste on the Cu pad surfaces of either organic solderable preservative (OSP) or electroless nickel immersion gold (ENIG). The assembly was tested for the effect of the formation extent of Ag3Sn intermetallic compound. Afterward a board-level pulse-controlled drop test was conducted on the as-reflowed assemblies according to the JESD22-B110 and JESD22-B111 standards, the impact performance of various surface finished halogen-free printed circuit board assembly was evaluated. The test results showed that most of the fractures occurred around the pad on the test board first. Then cracks propagated across the outer build-up layer. Finally, the inner copper trace was fractured due to the propagated cracks, resulting in the failure of the PCB side. Interfacial stresses numerically obtained by the transient stress responses supported the test observation as the simulated initial crack position was the same as that observed.

Sign in / Sign up

Export Citation Format

Share Document