scholarly journals Electrical characterization of epoxy-based molding compounds for next generation HV ICs in presence of moisture

2018 ◽  
Vol 88-90 ◽  
pp. 752-755
Author(s):  
D. Cornigli ◽  
S. Reggiani ◽  
A. Gnudi ◽  
E. Gnani ◽  
G. Baccarani ◽  
...  
Keyword(s):  
Electrical Characterization ◽  
Next Generation ◽  
Molding Compounds

Complementary Resistive Switches (CRS): High speed performance for the application in passive nanocrossbar arrays

2011 ◽  
Vol 1337 ◽  
Author(s):  
Roland Rosezin ◽  
Eike Linn ◽  
Lutz Nielen ◽  
Carsten Kügeler ◽  
Rainer Bruchhaus ◽  
...  
Keyword(s):  
High Speed ◽  
Simple Procedure ◽  
Electrical Characterization ◽  
Building Blocks ◽  
Next Generation ◽  
High Uniformity ◽  
Non Volatile Memory ◽  
Speed Performance ◽  
Resistive Switches

ABSTRACTIn this report, the fabrication and electrical characterization of fully vertically integrated complementary resistive switches (CRS), which consist of two anti-serially connected Cu-SiO2 memristive elements, is presented. The resulting CRS cells are initialized by a simple procedure and show high uniformity of resistance states afterwards. Furthermore, the CRS cells show high switching speeds below 50 ns, making them excellent building blocks for next generation non-volatile memory based on passive nanocrossbar arrays.

Structural and Electrical Characterization of Shaped Beam Laser Recrystallized Polysilicon on Amorphous Substrates

1981 ◽  
Vol 4 ◽  
Author(s):  
T. J. Stultz ◽  
J. F. Gibbons
Keyword(s):  
Grain Size ◽  
Electrical Characterization ◽  
Grain Structure ◽  
Electrical Characteristics ◽  
Shaped Beam ◽  
Beam Laser ◽  
Cw Laser ◽  
Amorphous Substrates ◽  
Circular Beam

ABSTRACTStructural and electrical characterization of laser recrystallized LPCVD silicon films on amorphous substrates using a shaped cw laser beam have been performed. In comparing the results to data obtained using a circular beam, it was found that a significant increase in grain size can be achieved and that the surface morphology of the shaped beam recrystallized material was much smoother. It was also found that whereas circular beam recrystallized material has a random grain structure, shaped beam material is highly oriented with a <100> texture. Finally the electrical characteristics of the recrystallized film were very good when measured in directions parallel to the grain boundaries.

Vapor Deposition Polymerization and Electrical Characterization of TPD Thin Films

2011 ◽  
Vol E94-C (2) ◽  
pp. 157-163 ◽  
Author(s):  
Masakazu MUROYAMA ◽  
Ayako TAJIRI ◽  
Kyoko ICHIDA ◽  
Seiji YOKOKURA ◽  
Kuniaki TANAKA ◽  
...  
Keyword(s):  
Thin Films ◽  
Vapor Deposition ◽  
Electrical Characterization

Electrical Characterization of Different Failure Modes in Sub-100 nm Devices Using Nanoprobing Technique

2009 ◽  
Author(s):  
E. Hendarto ◽  
S.L. Toh ◽  
J. Sudijono ◽  
P.K. Tan ◽  
H. Tan ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Focused Ion Beam ◽  
Failure Modes ◽  
Ion Beam ◽  
Electrical Characterization ◽  
Nickel Silicide ◽  
Fault Isolation ◽  
Technology Nodes ◽  
Scanning Electron

Abstract The scanning electron microscope (SEM) based nanoprobing technique has established itself as an indispensable failure analysis (FA) technique as technology nodes continue to shrink according to Moore's Law. Although it has its share of disadvantages, SEM-based nanoprobing is often preferred because of its advantages over other FA techniques such as focused ion beam in fault isolation. This paper presents the effectiveness of the nanoprobing technique in isolating nanoscale defects in three different cases in sub-100 nm devices: soft-fail defect caused by asymmetrical nickel silicide (NiSi) formation, hard-fail defect caused by abnormal NiSi formation leading to contact-poly short, and isolation of resistive contact in a large electrical test structure. Results suggest that the SEM based nanoprobing technique is particularly useful in identifying causes of soft-fails and plays a very important role in investigating the cause of hard-fails and improving device yield.

Case Studies in Atomic Force Probe Analysis

2006 ◽  
Author(s):  
Randal Mulder ◽  
Sam Subramanian ◽  
Tony Chrastecky
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Light Emission ◽  
Electrical Characterization ◽  
Logic Circuits ◽  
Contrast Imaging ◽  
Atomic Force ◽  
Measuring Surface ◽  
Analysis Environment

Abstract The use of atomic force probe (AFP) analysis in the analysis of semiconductor devices is expanding from its initial purpose of solely characterizing CMOS transistors at the contact level with a parametric analyzer. Other uses found for the AFP include the full electrical characterization of failing SRAM bit cells, current contrast imaging of SOI transistors, measuring surface roughness, the probing of metallization layers to measure leakages, and use with other tools, such as light emission, to quickly localize and identify defects in logic circuits. This paper presents several case studies in regards to these activities and their results. These case studies demonstrate the versatility of the AFP. The needs and demands of the failure analysis environment have quickly expanded its use. These expanded capabilities make the AFP more valuable for the failure analysis community.

Sign in / Sign up

Export Citation Format

Share Document