Investigation of the adhesion toughness of lacquer to zinc-phosphated steel

1991 ◽  
Vol 26 (23) ◽  
pp. 6423-6430 ◽  
Author(s):  
Y. M. Aravot ◽  
A. Albu-Yaron
Keyword(s):  
Phosphated Steel ◽  
Adhesion Toughness

Elucidation of corrosion failure mechanisms of coated phosphated steel substrates

2008 ◽  
Vol 5 (3) ◽  
pp. 311-325 ◽  
Author(s):  
Sarjak Amin ◽  
Sundaresan Avudaiappan ◽  
Askarali Johnpasha ◽  
Theodore Provder ◽  
F. Louis Floyd
Keyword(s):  
Failure Mechanisms ◽  
Corrosion Failure ◽  
Phosphated Steel ◽  
Steel Substrates

PLA deposition on surface treated magnesium alloy: Adhesion, toughness and corrosion behaviour

2020 ◽  
Vol 388 ◽  
pp. 125593 ◽  
Author(s):  
M. Muñoz ◽  
B. Torres ◽  
M. Mohedano ◽  
E. Matykina ◽  
R. Arrabal ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
Corrosion Behaviour ◽  
Adhesion Toughness

scholarly journals Determination of mode I and II adhesion toughness of monolayer thin films by circular blister tests

2018 ◽  
Vol 94 ◽  
pp. 34-39 ◽  
Author(s):  
Christopher M. Harvey ◽  
Simon Wang ◽  
Bo Yuan ◽  
Rachel C. Thomson ◽  
Gary W. Critchlow
Keyword(s):  
Thin Films ◽  
Mode I ◽  
Adhesion Toughness

Adhesion of lacquer to phosphated steel ? A shear test evaluation

1990 ◽  
Vol 25 (8) ◽  
pp. 3714-3722 ◽  
Author(s):  
Y. M. Aravot ◽  
Lelia Arcan ◽  
M. E. Arcan ◽  
Ana Albu-Yaron
Keyword(s):  
Shear Test ◽  
Test Evaluation ◽  
Phosphated Steel

Performance of polymer blends on phosphated steel substrate

2005 ◽  
Vol 54 (1) ◽  
pp. 1-4 ◽  
Author(s):  
M. Selvaraj ◽  
S. Palraj ◽  
P. Jayakrishnan
Keyword(s):  
Polymer Blends ◽  
Steel Substrate ◽  
Phosphated Steel

Measuring fracture toughness from machining tests

2009 ◽  
Vol 223 (12) ◽  
pp. 2861-2869 ◽  
Author(s):  
Y Patel ◽  
B R K Blackman ◽  
J G Williams
Keyword(s):  
Fracture Toughness ◽  
Aluminium Alloy ◽  
Coefficient Of Friction ◽  
Metal Cutting ◽  
Orthogonal Cutting ◽  
Shear Plane ◽  
Rake Angle ◽  
Sufficient Information ◽  
The Coefficient Of Friction ◽  
Adhesion Toughness

An analysis of the forces involved in orthogonal cutting or machining is presented in which yielding on a shear plane is assumed. The fracture toughness Gc is included and it is observed that Gc may be determined by measuring the cutting and transverse forces together with the chip thickness for a range of cutting depths. This latter measurement enabled the shear plane angle ϕ to be determined experimentally. A simplified version of the analysis is also given in which ϕ is predicted by a cutting force minimization scheme. Neither scheme requires any details of the friction condition to be known since the transverse force is sufficient information for any type to be included in the analysis. A friction model including a coefficient of friction and an adhesion toughness is also utilized. Data for both polymer and metal cutting are taken from the literature and Gc is determined. In some datasets the tool rake angle α is also varied and the values of Gc and the yield stress σY are found to be independent of α. The force minimization method gives a good estimate of ϕ for most polymers. For metals (aluminium alloy, steel, and brass) the method worked well. For aluminium alloy Gc was independent of α and the predicted and measured ϕ values agreed. For steel and brass this was not so. Gc was mostly independent of α except at low values where high values of Gc were observed. A constant value of the coefficient of friction was observed for each α value but values for both the coefficient of friction and the adhesion toughness varied significantly with increasing rake angle.

Sign in / Sign up

Export Citation Format

Share Document