Effects of niobium pentoxide nanoparticles on the tribological properties of electrodeposited ZnNi coatings

Electrodeposited ZnNi coatings are widely used to improve the corrosion resistance of steel substrates, but their tribological properties are also relevant for loaded contacts under relative motion. This work investigates the hypothesis of improving tribological properties of electrodeposited ZnNi coatings via dispersion of niobium pentoxide nanoparticles (1g/L) in the electrolytic bath. The niobium pentoxide nanoparticles were produced via hydrothermal synthesis assisted by microwave. The surface morphology and chemical composition of the coatings were analysed by scanning electron microscopy coupled with X-ray dispersive energy, X-ray diffraction and X-ray photoelectron spectroscopy. The tribological performance of the coatings was assessed using dry reciprocating ball-on-flat tests at normal loads between 3 and 6 N. The use of niobium pentoxide nanoparticles resulted in significantly denser coatings, with some Nb incorporated in the coated surfaces. Under the lowest normal load, all coated specimens showed relatively low friction (~0.2) and negligible damag. As the normal load increased, the coating produced using niobium pentoxide nanoparticles showed stronger adherence, while conventional ZnNi coating showed increased friction and spalling for the highest load. It is believed that the Nb2O5 nanoparticles increased the number of sites for heterogeneous nucleation, refining the microstructure, so that tougher and more adherent coatings were produced.

Process Simulation and Abrasion Behavior of Jet Electrodeposited Ni–TiN Nanocoatings

In this work, we study jet-electrodeposited Ni–TiN composite nanocoatings (CNCs) for improving abrasion resistance as a function of various nozzle diameters. In addition, COMSOL software is utilized to simulate the process of jet electrodeposition, particularly the influence of spraying speed and pressure of the electrolyte on the abrasion resistance of coatings. Optimization of the nozzle diameter to obtain uniform and high-performance coatings showed that a Φ7 mm nozzle diameter generated the optimum spraying speed and spraying pressure, which results in good micro-hardness and abrasion resistance of the Ni–TiN CNCs. Under these conditions, the 45 steel substrates are coated with a compact layer of uniform and nano-sized TiN particles, which are responsible for the high abrasion resistance of our Ni–TiN CNCs. Our study may motivate researchers to study jet electrodeposition in order to obtain abrasion-resistant coatings.

Tribological Properties of Carbon Nanotube and Carbon Nanofiber Blended Polyvinylidene Fluoride Sheets Laminated on Steel Substrates

Nanostructured carbon dispersed polymer nanocomposites are promising materials for tribological applications. Carbon nanofiber (CNF) and carbon nanotube (CNT) dispersed polyvinylidene fluoride (PVDF) nanocomposite was prepared by chemical synthesis route. Morphology and microstructure of well-dispersed CNF and CNT in PVDF were specified by scanning electron microscope and X-ray diffraction, respectively. Moreover, chemical and functional characteristics were examined by Raman spectroscopy and FTIR investigation. The friction coefficient of PVDF nanocomposite laminated on steel substrate decreased with an increase in the dispersed quantity of CNF and CNT. The friction coefficient of PVDF is approximately 0.27; however, the addition of carbon nanomaterial in PVDF will further decrease the friction coefficient between 0.24 and 0.17. This value was significantly less in CNT dispersed PVDF nanocomposite. This could be explained by easy shearing and rolling action contact interfaces.

Assessment of Adhesion of Geopolymer and Varnished Coatings by the Pull-Off Method

This paper presents the results of testing the adhesion of geopolymer coatings and varnishes with ceramic additives to concrete and steel substrates. The measurement method used and described in this article was the pull-off method. The pull-off method test provides an easy way to evaluate the degree of adhesion of coatings to metal surfaces. The pull-off device provides values for the peel stress, which not only allows a quick determination of the adhesion of the coating to the substrate, but also makes it easier to compare the adhesion of several coatings to each other. However, this method requires appropriate preparation, so an attempt was made to determine its suitability for geopolymer layers. The results of testing the adhesion of a geopolymer layer to a geopolymer substrate and a concrete substrate are presented. As a result of this study, a higher adhesion strength of the geopolymer layer to the geopolymer substrate was found in comparison to geopolymer coatings applied on conventional concrete. Adhesion tests were also conducted for steel substrates to which both geopolymer and acrylic lacquer were applied.

Corrosion resistance evaluation of carbon and vanadium-based sputtered coatings on steel substrates

Steels are in constant contact with fluids that could generate corrosion regardless the application in which this steel is located. AISI-SAE 1045 like steels is widely used in different applications in engineering, even several of these parts made of this steel suffers wear processes. The synergy between corrosion and wear phenomena exacerbates the detriment of some physical properties of the material conducing it to a failure. A potential alternative to avoid this issue is to coat the material surface with an anticorrosive material, and among different techniques to produce coatings, physical vapor deposition ones are environmentally friendly, secure and with excellent properties on the final product. We report the production of coatings based on vanadium and carbon on AISI-SAE 1045 steels substrates varying some of the deposition parameters in a sputtering coatings machine. A 23-factorial design of experiments was done with power applied to the vanadium target, power applied to the carbon target and temperature as active factors with two levels each one. A relevant effect of the power applied to V target and temperature on the anticorrosive properties of the coatings was found, thus increasing these factors levels always gives higher surface roughness and higher corrosion rates, this result together provides an important insight into the values that must be considered to achieve good anticorrosive properties on the material. Overall, these results indicate that with low V target power and room temperature, and high C target power the lowest corrosion rates and roughness of the group are achieved, both results agree.

Corrosion Properties of S-Phase/Cr2N Composite Coatings Deposited on Austenitic Stainless Steel

In order to study the suitability of the S-phase layers as the interlayer for Cr2N chromium nitride coatings, a number of composite coatings were deposited by the reactive magnetron sputtering (RMS) method on austenitic steel substrates with various initial surface conditions (as delivered and polished) and their corrosion resistance was assessed. Coatings with S-phase interlayer were deposited at three different nitrogen contents in the working atmosphere (15%, 30%, and 50%), which influenced the nitrogen concentration in the S-phase. Coatings with chromium, as a traditional interlayer to improve adhesion, and uncoated austenitic stainless steel were used as reference materials. Detailed microstructural and phase composition studies of the coatings were carried out by means of scanning electron microscopy (SEM), optical microscopy (LM), and X-ray diffraction (XRD) and were discussed in the context of results of corrosion tests carried out with the use of the potentiodynamic polarization method conducted in a 3% aqueous solution of sodium chloride (NaCl). The performed tests showed that the electrochemical potential of the S-phase/Cr2N composite coatings is similar to that of Cr/Cr2N coatings. It was also observed that the increase in the nitrogen content in the S-phase interlayer causes an increase in the polarization resistance of the S-phase/Cr2N composite coating. Moreover, with a higher nitrogen content in the S-phase interlayer, the polarization resistance of the S-phase/Cr2N coating is higher than for the Cr/Cr2N reference coating. All the produced composite coatings showed better corrosion properties in relation to the uncoated austenitic stainless steel.

Study of the influence of diamond-like carbon film deposition technology on the change of its physical and mechanical characteristics

The paper presents the results of testing the technology of deposition of diamond-like carbon films on the surface of stainless steel substrates at different process parameters, a quantitative assessment of the sp3 bond content and the physical and mechanical characteristics of the coatings obtained, a conclusion about the influence of the deposition process technological parameters on these characteristics is formulated.

Electroless Ni–P Plating on Mullite Powders and Study of the Mechanical Properties of Its Plasma-Sprayed Coating

To effectively improve the properties of a mullite coating and its interfacial bonding with the substrate, a Ni–P layer is deposited on the surface of mullite powders by electroless plating. The original mullite powders and coated mullite powders are then deposited onto stainless-steel substrates by plasma spraying. The growth mechanism of the Ni–P layer during the plating, the microstructures of the coated powders and mullite coating and the properties of the mullite coatings are characterized and analyzed. The results indicate that the Ni–P layer on the surface of the mullite powder has cell structures with a dense uniform distribution and grows in layers on the surface of the mullite powder. The crystallization behavior of Ni-P amorphous layer is induced by heat treatment. Compared to the original mullite coating, the coating prepared by the coated mullite powders has better manufacturability, stronger adhesion to the substrate, lower porosity (7.40%, 65% of that of the original coating), higher hardness (500.1 HV, 1.2 times that of the original coating), and better thermal cycle resistance (two times that of the original coating). The method of preparation of high-temperature thermal barrier coatings with coated mullite powders has a high application value.