The effect of environmental moisture on the adhesion toughness of epoxy-coated phosphated steels

1993 ◽  
Vol 12 (18) ◽  
pp. 1437-1438 ◽  
Author(s):  
Y. M. Aravot ◽  
A. Albu-Yaron
Keyword(s):  
Adhesion Toughness

PLA deposition on surface treated magnesium alloy: Adhesion, toughness and corrosion behaviour

2020 ◽  
Vol 388 ◽  
pp. 125593 ◽  
Author(s):  
M. Muñoz ◽  
B. Torres ◽  
M. Mohedano ◽  
E. Matykina ◽  
R. Arrabal ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
Corrosion Behaviour ◽  
Adhesion Toughness

scholarly journals Determination of mode I and II adhesion toughness of monolayer thin films by circular blister tests

2018 ◽  
Vol 94 ◽  
pp. 34-39 ◽  
Author(s):  
Christopher M. Harvey ◽  
Simon Wang ◽  
Bo Yuan ◽  
Rachel C. Thomson ◽  
Gary W. Critchlow
Keyword(s):  
Thin Films ◽  
Mode I ◽  
Adhesion Toughness

Measuring fracture toughness from machining tests

2009 ◽  
Vol 223 (12) ◽  
pp. 2861-2869 ◽  
Author(s):  
Y Patel ◽  
B R K Blackman ◽  
J G Williams
Keyword(s):  
Fracture Toughness ◽  
Aluminium Alloy ◽  
Coefficient Of Friction ◽  
Metal Cutting ◽  
Orthogonal Cutting ◽  
Shear Plane ◽  
Rake Angle ◽  
Sufficient Information ◽  
The Coefficient Of Friction ◽  
Adhesion Toughness

An analysis of the forces involved in orthogonal cutting or machining is presented in which yielding on a shear plane is assumed. The fracture toughness Gc is included and it is observed that Gc may be determined by measuring the cutting and transverse forces together with the chip thickness for a range of cutting depths. This latter measurement enabled the shear plane angle ϕ to be determined experimentally. A simplified version of the analysis is also given in which ϕ is predicted by a cutting force minimization scheme. Neither scheme requires any details of the friction condition to be known since the transverse force is sufficient information for any type to be included in the analysis. A friction model including a coefficient of friction and an adhesion toughness is also utilized. Data for both polymer and metal cutting are taken from the literature and Gc is determined. In some datasets the tool rake angle α is also varied and the values of Gc and the yield stress σY are found to be independent of α. The force minimization method gives a good estimate of ϕ for most polymers. For metals (aluminium alloy, steel, and brass) the method worked well. For aluminium alloy Gc was independent of α and the predicted and measured ϕ values agreed. For steel and brass this was not so. Gc was mostly independent of α except at low values where high values of Gc were observed. A constant value of the coefficient of friction was observed for each α value but values for both the coefficient of friction and the adhesion toughness varied significantly with increasing rake angle.

An Indentation Test for Measuring Adhesion Toughness of Thin Films Under High Residual Compression With Application to Diamond Films

1995 ◽  
Vol 383 ◽  
Author(s):  
M. D. Drory ◽  
J. W. Hutchinson
Keyword(s):  
Thin Films ◽  
Diamond Films ◽  
Indentation Test ◽  
Indentation Method ◽  
Interface Toughness ◽  
Film Adhesion ◽  
Adhesion Measurement ◽  
Ductile Substrates ◽  
Residual Compression ◽  
Adhesion Toughness

ABSTRACTAdhesion measurement of brittle coatings on ductile substrates is examined with emphasis on diamond–coated metals. The experimental aspects of determining film adhesion is discussed through measurement of the interface toughness by a brale indentation method.

scholarly journals Determination of residual stress and interface adhesion toughness of thin films by blisters

2019 ◽  
Vol 1 (5) ◽  
Author(s):  
Bo Yuan ◽  
Christopher M. Harvey ◽  
Gary W. Critchlow ◽  
Rachel C. Thomson ◽  
Simon Wang
Keyword(s):  
Thin Films ◽  
Residual Stress ◽  
Interface Adhesion ◽  
Adhesion Toughness

Effect of some thermal treatments on interface adhesion toughness of various thick thermal spray coatings

2006 ◽  
Vol 22 (5) ◽  
pp. 390-398 ◽  
Author(s):  
D. Chicot ◽  
G. Marot ◽  
P. Araujo ◽  
N. Horny ◽  
A. Tricoteaux ◽  
...  
Keyword(s):  
Thermal Spray ◽  
Thermal Spray Coatings ◽  
Thermal Treatments ◽  
Interface Adhesion ◽  
Spray Coatings ◽  
Adhesion Toughness

Analysis of the adhesion toughness of a CVD diamond coating

2004 ◽  
Vol 71 (4-6) ◽  
pp. 669-679 ◽  
Author(s):  
G. Cianflone ◽  
F.M. Furgiuele ◽  
G. Sciumé
Keyword(s):  
Cvd Diamond ◽  
Diamond Coating ◽  
Cvd Diamond Coating ◽  
Adhesion Toughness

Application of the interfacial indentation test for adhesion toughness determination

2005 ◽  
Vol 200 (1-4) ◽  
pp. 174-177 ◽  
Author(s):  
D. Chicot ◽  
P. Araujo ◽  
N. Horny ◽  
A. Tricoteaux ◽  
J. Lesage
Keyword(s):  
Indentation Test ◽  
Adhesion Toughness
Sign in / Sign up

Export Citation Format

Share Document