Microdroplet Actuation via Light Line Optoelectrowetting (LL-OEW)

Meanwhile, electrowetting-on-dielectric (EWOD) is a well-known phenomenon, even often exploited in active micro-optics to change the curvature of microdroplet lenses or in analytical chemistry with digital microfluidics (DMF, lab on a chip 2.0) to move/actuate microdroplets. Optoelectrowetting (OEW) can bring more flexibility to DMF because in OEW, the operating point of the lab chip is locally controlled by a beam of light, usually impinging onto the chip perpendicularly. As opposed to pure EWOD, for OEW, none of the electrodes has to be structured, which makes the chip design and production technology simpler; the path of any actuated droplet is determined by the movement of the light spot. However, for applications in analytical chemistry, it would be helpful if the space both below as well as that above the lab chip were not obstructed by any optical components and light sources. Here, we report on the possibility to actuate droplets by laser light beams, which traverse the setup parallel to the chip surface and inside the OEW layer sequence. Since microdroplets are grabbed by this surface-parallel, nondiverging, and nonexpanded light beam, we call this principle “light line OEW” (LL-OEW).

Energy harvesting performance of an EDLC power generator based on pure water and glycerol mixture: analytical modeling and experimental validation

A liquid droplet oscillating between two plane electrodes was visualized, and the electrical power generation based on the reverse-electrowetting-on-dielectric (REWOD) phenomenon was measured. For the upper plate, a hydrophobic surface treated by PTFE was used, and the lower plate was tested using the hydrophilic surface properties of ITO glass. To analyze the dynamic behavior of an oscillating liquid bridge, a modeling study was carried out using the phase field method based on the finite element method. The dynamic contact angle of the oscillating liquid bridge was modeled based on advancing and receding contact angles. The variable interfacial areas between the liquid and solid surfaces were calculated and agreed well with the experimental results within a 10% error band. Furthermore, experimental and analytical studies were carried out to examine the REWOD energy harvesting characteristics of the glycerol-water mixtures in various concentrations. As a result, the peak voltage output was obtained at a specific concentration of the glycerol mixture, and the power density of the oscillating liquid bridge at this point was up to 2.23 times higher than that of pure water.

Droplet Transportation through an Orifice on Electrode for Digital Microfluidics Modulations

A digital microfluidic modular interface (chip-to-chip interface) which possesses an electrode with an orifice to vertically transport core–shell droplets is presented. The electrodes were geometrically designed to promote droplet deformation and suspension. The droplets were then applied with an electrical potential for insertion into and passage through the orifice. The concepts were tested with three types of droplets at the volume of 0.75~1.5 μL, which is usually difficult to transfer through an orifice. The integration of electrowetting on dielectric (EWOD) with paper-based microfluidics was demonstrated: the droplet could be transported within 10 s. More importantly, most of the core droplet (~97%) was extracted and passed through with only minimal shell droplets accompanying it.

Solution for Mass Production of High-Throughput Digital Microfluidic Chip Based on a-Si TFT with In-Pixel Boost Circuit

As one of the most popular research hotspot of lab-on-chip, digital microfluidic (DMF) technology based on the principle of electrowetting has unique advantages of high-precision, low cost and programmable control. However, due to the limitation of electrodes number, the throughput is hard to further upgrade. Therefore, active matrix electrowetting-on-dielectric (AM-EWOD) technology is a solution to acquire larger scale of driving electrodes. However, the process of manufacturing of AM-EWOD based on thin-film-transistor (TFT) is complex and expensive. Besides, the driving voltage of DMF chip is usually much higher than that of common display products.In this paper, a solution for mass production of AM-EWOD based on amorphous silicon (a-Si) is provided. Samples of 32 × 32 matrix AM-EWOD chips was designed and manufactured. A boost circuit was integrated into the pixel, which can raise the pixel voltage up by about 50%. Customized designed Printed Circuit Board (PCB) was used to supply the timing signals and driving voltage to make the motion of droplets programmable. The process of moving, mixing and generation of droplets was demonstrated.The minimum voltage in need was about 20 V and a velocity of up to 96 mm/s was achieved. Such an DMF device with large-scale matrix and low driving voltage will be very suitable for POCT applications.

Virtual Stencil for Patterning and Modeling in a Quantitative Volume Using EWOD and DEP Devices for Microfluidics

Applying microfluidic patterning, droplets were precisely generated on an electrowetting-on-dielectric (EWOD) chip considering these parameters: number of generating electrodes, number of cutting electrodes, voltage, frequency and gap between upper and lower plates of the electrode array on the EWOD chip. In a subsequent patterning experiment, an environment with three generating electrodes, one cutting electrode and a gap height 10 μm, we obtained a quantitative volume for patterning. Propylene carbonate liquid and a mixed colloid of polyphthalate carbonate (PPC) and photosensitive polymer material were manipulated into varied patterns. With support from a Z-axis lifting platform and a UV lamp, a cured 3D structure was stacked. Using an EWOD system, a multi-layer three-dimensional structure was produced for the patterning. A two-plate EWOD system patterned propylene carbonate in a quantitative volume at 140 Vpp/20 kHz with automatic patterning.

Dynamics of droplets under electrowetting effect with voltages exceeding the contact angle saturation threshold

Electrowetting on dielectric (EWOD) is a powerful tool in many droplet-manipulation applications with a notorious weakness caused by contact-angle saturation (CAS), a phenomenon limiting the equilibrium contact angle of an EWOD-actuated droplet at high applied voltage. In this paper, we study the spreading behaviours of droplets on EWOD substrates with the range of applied voltage exceeding the saturation limit. We experimentally find that at the initial stage of spreading, the driving force at the contact line still follows the Young–Lippmann law even if the applied voltage is higher than the CAS voltage. We then theoretically establish the relation between the initial contact-line velocity and the applied voltage using the force balance at the contact line. We also find that the amplitude of capillary waves on the droplet surface generated by the contact line's initial motion increases with the applied voltage. We provide a working framework utilising EWOD with voltages beyond CAS by characterising the capillary waves formed on the droplet surface and their self-similar behaviours. We finally propose a theoretical model of the wave profiles taking into account the viscous effects and verify this model experimentally. Our results provide avenues to utilise the EWOD effect with voltages beyond the CAS threshold, and have strong bearing on emerging applications such as digital microfluidic and ink-jet printing.