scholarly journals Production and Compression Strength of Mortars Containing Unprocessed Waste Powdered Steel Slag

2017 ◽  
Vol 9 (12) ◽  
pp. 2372 ◽  
Author(s):  
◽  
◽  
◽  
◽  
◽  
...  
Keyword(s):  
Compression Strength ◽  
Steel Slag ◽  
Powdered Steel

scholarly journals Chemical and Unconfined Compression Strength Properties of Steel Slag Mixed Problematic Soil

2020 ◽  
Vol 15 (3) ◽  
pp. 509-517
Author(s):  
Yuji SUGIMURA ◽  
Haruhiko SINOZAKI ◽  
Yuzoh AKASHI ◽  
Shodai UEMATSU ◽  
Satoru SHIBUYA ◽  
...  
Keyword(s):  
Compression Strength ◽  
Steel Slag ◽  
Strength Properties ◽  
Unconfined Compression Strength ◽  
Unconfined Compression ◽  
Problematic Soil

scholarly journals Long Term Compression Strength of Mortars Produced Using Coarse Steel Slag as Aggregate

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Erika Furlani ◽  
Stefano Maschio
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compression Strength ◽  
Steel Slag ◽  
Alkali Silica Reaction ◽  
Steelmaking Slag ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Long Time

The paper reports on some experimental results obtained from the production of mortars prepared using a commercial cement, coarse steelmaking slag, superplasticizer, and water. The behaviour of this reference composition was compared to that of some others containing further additives in order to investigate materials compressive strength after long time ageing. It has been demonstrated that an optimized water/cement ratio coupled with slag particles of size lower than 2.5 mm and proper protocol of preparation leads to the production of materials with good mechanical properties after 28, 90, and 180 days of ageing. The resulting materials therefore appeared as good candidates for civil engineering applications. However, the present research also demonstrates that the mortar samples of all of the compositions prepared suffer from decay and compressive strength decrease after long time ageing in water. In the present paper the results are explained taking account of materials residual porosity and alkali silica reaction which occurs in the samples.

Evaluate the Expressions of Compression Strength and UPV Relationship

2018 ◽  
Vol 10 (8) ◽  
Author(s):  
Abdelmajeed Altlomate ◽  
◽  
Shahiron Shahidan ◽  
Faesal Alatshan ◽  
Mohammed Elkher ◽  
...  
Keyword(s):  
Compression Strength

Effect of Titanium Carbide Particles on Mechanical Properties of Aluminum Matrix Composites

2017 ◽  
Vol 5 (2) ◽  
pp. 20-30
Author(s):  
Zaman Khalil Ibrahim
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Compression Strength ◽  
Volume Fraction ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Powder Metallurgy Technique ◽  
Carbide Particles ◽  
Properties Of Composites

In this research aluminum matrix composites (AMCs) was reinforced by titanium carbide (TiC) particles and was produced. Powder metallurgy technique (PM) has been used to fabricate AMCs reinforced with various amounts (0%, 4%, 8%, 12%, 16% and 20% volume fraction) of TiC particles to study the effect of different volume fractions on mechanical properties of the Al-TiC composites. Measurements of compression strength and hardness showed that mechanical properties of composites increased with an increase in volume fraction of TiC Particles. Al-20 % vol. TiC composites exhibited the best properties with hardness value (97HRB) and compression strength value (275Mpa).

PRESSURDIE-3

Alloy Digest ◽  
1954 ◽  
Vol 3 (3) ◽  
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Compression Strength ◽  
Heat Treating ◽  
Compression Molding ◽  
Type Alloy ◽  
High Compression ◽  
Steel Industries ◽  
Class Iv

Abstract PRESSURDIE-3, developed particularly for injection and compression molding, has high compression strength, wear resistance, and corrosion resistance. It is a ASM Class IV-B type alloy. This datasheet provides information on composition and hardness. It also includes information on forming, heat treating, and machining. Filing Code: TS-19. Producer or source: Continental Copper & Steel Industries Inc..

MILNE CMV

Alloy Digest ◽  
1961 ◽  
Vol 10 (11) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Tensile Properties ◽  
Tool Steel ◽  
Compression Strength ◽  
Heat Treating ◽  
Medium Carbon ◽  
Temperature Performance

Abstract Milne CMV is a 5% chromium, medium-carbon hot work tool steel, having high compression strength, wear resistance, and corrosion resistance. This datasheet provides information on composition, hardness, and tensile properties as well as fracture toughness and creep. It also includes information on high temperature performance as well as forming, heat treating, machining, and joining. Filing Code: TS-111. Producer or source: A. Milne & Company (Distributor).

Sign in / Sign up

Export Citation Format

Share Document