scholarly journals Phase Shift Migration with Modified Coherent Factor Algorithm for MIMO-SAR 3D Imaging in THz Band

2021 ◽  
Vol 13 (22) ◽  
pp. 4701
Author(s):  
Guan Yang ◽  
Chao Li ◽  
Shiyou Wu ◽  
Shen Zheng ◽  
Xiaojun Liu ◽  
...  
Keyword(s):  
Phase Shift ◽  
3D Imaging ◽  
Imaging System ◽  
Multiple Input Multiple Output ◽  
Three Dimensional ◽  
Structural Similarity ◽  
Projection Algorithm ◽  
Wavenumber Domain ◽  
Reflection Model ◽  
Coherent Factor

In multiple-input-multiple-output synthetic aperture radar (MIMO-SAR) systems, sparse arrays are usually applied, resulting in increased sidelobes of the point spread function. In this paper, a phase shift migration (PSM) imaging algorithm based on the explosion reflection model with modified coherent factor was proposed for sidelobe suppression in MIMO-SAR three-dimensional (3D) imaging application. By defining the virtual difference wavenumber, reconstructing the raw echo by data rearrangement in wavenumber domain, the original coherent factor algorithm operating in spatial domain can be achieved by the PSM algorithm frame in the wavenumber domain, which means two orders of magnitude increase in computational efficiency. The correctness of the theory is verified by simulation. Finally, a bistatic prototype imaging system in the 0.3 THz band was designed for the proof-of-principle experiments. The experimental results show that the proposed algorithm has a 0.948 structural similarity value to the original coherent factor back-projection algorithm (CF-BPA) which means comparable image quality with much superior efficiency.

scholarly journals Three-dimensional imaging of hold baggage for airport security

2014 ◽  
Vol XL-5 ◽  
pp. 331-336
Author(s):  
S. Kolokytha ◽  
R. Speller ◽  
S. Robson
Keyword(s):  
3D Imaging ◽  
Imaging System ◽  
Tomographic Reconstruction ◽  
Three Dimensional ◽  
Handling Time ◽  
Cost Effective ◽  
Airport Security ◽  
X Ray ◽  
Common System ◽  
Close Range

This study describes a cost-effective check-in baggage screening system, based on "on-belt tomosynthesis" (ObT) and close-range photogrammetry, that is designed to address the limitations of the most common system used, conventional projection radiography. The latter's limitations can lead to loss of information and an increase in baggage handling time, as baggage is manually searched or screened with more advanced systems. This project proposes a system that overcomes such limitations creating a cost-effective automated pseudo-3D imaging system, by combining x-ray and optical imaging to form digital tomograms. Tomographic reconstruction requires a knowledge of the change in geometry between multiple x-ray views of a common object. This is uniquely achieved using a close range photogrammetric system based on a small network of web-cameras. This paper presents the recent developments of the ObT system and describes recent findings of the photogrammetric system implementation. Based on these positive results, future work on the advancement of the ObT system as a cost-effective pseudo-3D imaging of hold baggage for airport security is proposed.

scholarly journals A Microwave Three-Dimensional Imaging Method Based on Optimal Wave Spectrum Reconstruction

Sensors ◽  
2020 ◽  
Vol 20 (24) ◽  
pp. 7306
Author(s):  
Yan Zhang ◽  
Baoping Wang ◽  
Yang Fang ◽  
Zuxun Song
Keyword(s):  
3D Imaging ◽  
Imaging System ◽  
Wave Spectrum ◽  
Sampling Rate ◽  
Three Dimensional ◽  
Imaging Method ◽  
Data Sampling ◽  
Spectrum Reconstruction ◽  
Memory Space ◽  
Target Wave

Limited by the Shannon–Nyquist sampling law, the number of antenna elements and echo signal data of the traditional microwave three-dimensional (3D) imaging system are extremely high. Compressed sensing imaging methods based on sparse representation of target scene can reduce the data sampling rate, but the dictionary matrix of these methods takes a lot of memory, and the imaging has poor quality for continuously distributed targets. For the above problems, a microwave 3D imaging method based on optimal wave spectrum reconstruction and optimization with target reflectance gradient is proposed in this paper. Based on the analysis of the spatial distribution characteristics of the target echo in the frequency domain, this method constructs an orthogonal projection reconstruction model for the wavefront to realize the optimal reconstruction of the target wave spectrum. Then, the inverse Fourier transform of the optimal target wave spectrum is optimized according to the law of the target reflectance gradient distribution. The proposed method has the advantages of less memory space and less computation time. What is more, the method has a better imaging quality for the continuously distributed target. The computer simulation experiment and microwave anechoic chamber measurement experiment verify the effectiveness of the proposed method.

Volume Imaging in Fluoroscopy

1996 ◽  
Vol 37 (3P2) ◽  
pp. 741-748 ◽  
Author(s):  
Z. Kolitsi ◽  
N. Yoldassis ◽  
T. Siozos ◽  
N. Pallikarakis
Keyword(s):  
Cross Sections ◽  
Imaging System ◽  
Three Dimensional ◽  
Region Of Interest ◽  
Projection Algorithm ◽  
Digital Tomosynthesis ◽  
Presentation Modality ◽  
Volume Imaging ◽  
Volume Of Interest ◽  
Projection Images

Purpose: This work involves the development of a new digital tomosynthesis technique into a clinical prototype imaging system for the three-dimensional visualization of patient anatomy. Material and Methods: The multiple projection algorithm (MPA) has been developed into a clinical prototype imaging system comprising a digital chain that is interfaced with an isocentric fluoroscopic unit to form an integrated DTS facility. Planes of varying orientations can be synthesized retrospectively on the basis of an acquired set of appropriate projection images extending over the whole volume of interest. Results and Conclusion: The system provides an image reconstruction and processing facility that can effectively augment fluoroscopic examinations. Reconstruction times of a few seconds per plane have been achieved. The region of interest can be approached by tracking through cross-sections with user-selected orientations. Anatomical planes of particular interest can be identified and their reconstructed images can be stored. The characteristics of the image presentation modality have the potential to extend the field of current digital tomosynthesis applications to new areas in radiology and other clinical domains.

scholarly journals Application of Three-Dimensional Imaging to the Intestinal Crypt Organoids and Biopsied Intestinal Tissues

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Yun Chen ◽  
Ya-Hui Tsai ◽  
Yuan-An Liu ◽  
Shih-Hua Lee ◽  
Sheng-Hong Tseng ◽  
...  
Keyword(s):  
3D Imaging ◽  
Imaging System ◽  
3D Structure ◽  
Three Dimensional ◽  
Spatial Relationship ◽  
Intestinal Transplantation ◽  
Muscle Layer ◽  
3D Images ◽  
Nerve Network ◽  
Transplant Patients

Two-dimensional (2D) histopathology is the standard analytical method for intestinal biopsied tissues; however, the role of 3-dimensional (3D) imaging system in the analysis of the intestinal tissues is unclear. The 3D structure of the crypt organoids from the intestinal stem cell culture and intestinal tissues from the donors and recipients after intestinal transplantation was observed using a 3D imaging system and compared with 2D histopathology and immunohistochemistry. The crypt organoids and intestinal tissues showed well-defined 3D structures. The 3D images of the intestinal tissues with acute rejection revealed absence of villi and few crypts, which were consistent with the histopathological features. In the intestinal transplant for megacystis microcolon intestinal hypoperistalsis syndrome, the donor’s intestinal tissues had well-developed nerve networks and interstitial cells of Cajal (ICCs) in the muscle layer, while the recipient’s intestinal tissues had distorted nerve network and the ICCs were few and sparsely distributed, relative to those of the donor. The 3D images showed a clear spatial relationship between the microstructures of the small bowel and the features of graft rejection. In conclusion, integration of the 3D imaging and 2D histopathology provided a global view of the intestinal tissues from the transplant patients.

Validation of a Vision-Based, Three-Dimensional Facial Imaging System

2003 ◽  
Vol 40 (5) ◽  
pp. 523-529 ◽  
Author(s):  
A. Ayoub ◽  
A. Garrahy ◽  
C. Hood ◽  
J. White ◽  
M. Bock ◽  
...  
Keyword(s):  
3D Imaging ◽  
Cleft Lip ◽  
Imaging System ◽  
Three Dimensional ◽  
Procrustes Analysis ◽  
Facial Morphology ◽  
3D Images ◽  
Registration Errors ◽  
Measuring Machine ◽  
Full Face

Objective The aim of this study was to assess the accuracy of a newly developed three-dimensional (3D) imaging system in recording facial morphology. Methods Twenty-one infants with cleft lip each had a full-face alginate impression taken at the time of primary lip repair, and a stone cast was constructed from each impression. Five anthropometric points were marked on each cast. Each cast was digitized, and the 3D co-ordinates of the five points were obtained using a co-ordinate measuring machine (CMM, Ferranti) of documented accuracy (9.53 μm). Each cast was scanned in four positions using a computerized stereophotogrammetry (C3D) system. The five points were located on the 3D images, and their 3D co-ordinates were extracted by three operators. The co-ordinate systems produced by C3D were aligned, via translation and rotation, to match the CMM co-ordinate system using partial ordinary procrustes analysis. The displacements of the adjusted C3D co-ordinates from the reference co-ordinates were then measured. Three different types of errors were identified: operator, system, and registration errors. Results Operator error was within 0.2 mm of the true co-ordinates of the landmarks. C3D was accurate within 0.4 mm. The average displacement of points over the 21 casts at four positions for the three operators was 0.79 mm (median 0.68). Conclusions The presented 3D imaging system is reliable in recording facial deformity and could be utilized in recording cleft deformities and measuring the changes following surgery

scholarly journals Accuracy and Precision of Three-dimensional Imaging System of Children’s Facial Soft Tissue

2020 ◽  
Vol 47 (1) ◽  
pp. 17-24
Author(s):  
Kyunghwa Choi ◽  
Misun Kim ◽  
Koeun Lee ◽  
Okhyung Nam ◽  
Hyo-seol Lee ◽  
...  
Keyword(s):  
Soft Tissue ◽  
3D Imaging ◽  
Imaging System ◽  
Three Dimensional ◽  
Facial Growth ◽  
3D Scanner ◽  
Facial Soft Tissue ◽  
Linear Measurements ◽  
Accuracy And Precision ◽  
3D Photogrammetry

The purpose of this study was to evaluate the accuracy and precision of the three-dimensional (3D) imaging system of children’s facial soft tissue by comparing linear measurements. The subjects of the study were 15 children between the ages of 7 and 12. Twenty-three landmarks were pointed on the face of each subject and 16 linear measurements were directly obtained 2 times using an electronic caliper. Two sets of 3D facial images were made by the 3D scanner. The same 16 measurements were obtained on each 3D image. In the accuracy test, the total average difference was 0.9 mm. The precision of 3D photogrammetry was almost equivalent to that of direct measurement. Thus, 3D photogrammetry by the 3D scanner in children had sufficient accuracy and precision to be used in clinical setting. However, the 3D imaging system requires the subject’s compliance for exact images. If the clinicians provide specific instructions to children while obtaining 3D images, the 3D device is useful for investigating children’s facial growth and development. Also the device can be a valuable tool for evaluating the results of orthodontic and orthopedic treatments.

scholarly journals Non-Scanning Three-Dimensional Imaging System with a Single-Pixel Detector: Simulation and Experimental Study

2020 ◽  
Vol 10 (9) ◽  
pp. 3100
Author(s):  
Guang Shi ◽  
Leijue Zheng ◽  
Wen Wang ◽  
Keqing Lu
Keyword(s):  
3D Imaging ◽  
Imaging System ◽  
Three Dimensional ◽  
Scanning Laser ◽  
Pixel Detector ◽  
Reconstruction Algorithms ◽  
Imaging Technology ◽  
Area Array ◽  
Array Detectors ◽  
Single Pixel

Existing scanning laser three-dimensional (3D) imaging technology has slow measurement speed. In addition, the measurement accuracy of non-scanning laser 3D imaging technology based on area array detectors is limited by the resolution and response frequency of area array detectors. As a result, applications of laser 3D imaging technology are limited. This paper completed simulations and experiments of a non-scanning 3D imaging system with a single-pixel detector. The single-pixel detector can be used to achieve 3D imaging of a target by compressed sensing to overcome the shortcomings of the existing laser 3D imaging technology. First, the effects of different sampling rates, sparse transform bases, measurement matrices, and reconstruction algorithms on the measurement results were compared through simulation experiments. Second, a non-scanning 3D imaging experimental platform was designed and constructed. Finally, an experiment was performed to compare the effects of different sampling rates and reconstruction algorithms on the reconstruction effect of 3D imaging to obtain a 3D image with a resolution of 8 × 8. The simulation results show that the reconstruction effect of the Hadamard measurement matrix and the minimum total variation reconstruction algorithm performed well.

scholarly journals Three-Dimensional Interferometric ISAR Imaging Algorithm Based on Cross Coherence Processing

Sensors ◽  
2021 ◽  
Vol 21 (15) ◽  
pp. 5073
Author(s):  
Qian Lv ◽  
Shaozhe Zhang
Keyword(s):  
3D Imaging ◽  
High Efficiency ◽  
Imaging System ◽  
Computational Cost ◽  
Three Dimensional ◽  
Reconstruction Algorithm ◽  
Image Plane ◽  
Interferometric Phase ◽  
Isar Imaging ◽  
Reflectivity Function

Interferometric inverse synthetic aperture radar (InISAR) has received significant attention in three-dimensional (3D) imaging due to its applications in target classification and recognition. The traditional two-dimensional (2D) ISAR image can be interpreted as a filtered projection of a 3D target’s reflectivity function onto an image plane. Such a plane usually depends on unknown radar-target geometry and dynamics, which results in difficulty interpreting an ISAR image. Using the L-shape InISAR imaging system, this paper proposes a novel 3D target reconstruction algorithm based on Dechirp processing and 2D interferometric ISAR imaging, which can jointly estimate the effective rotation vector and the height of scattering center. In order to consider only the areas of the target with meaningful interferometric phase and mitigate the effects of noise and sidelobes, a special cross-channel coherence-based detector (C3D) is introduced. Compared to the multichannel CLEAN technique, advantages of the C3D include the following: (1) the computational cost is lower without complex iteration and (2) the proposed method, which can avoid propagating errors, is more suitable for a target with multi-scattering points. Moreover, misregistration and its influence on target reconstruction are quantitatively discussed. Theoretical analysis and numerical simulations confirm the suitability of the algorithm for 3D imaging of multi-scattering point targets with high efficiency and demonstrate the reliability and effectiveness of the proposed method in the presence of noise.

scholarly journals Interferenceless Coded Aperture Correlation Holography with Point Spread Holograms of Isolated Chaotic Islands for 3D Imaging

2021 ◽  
Author(s):  
Nitin Dubey ◽  
Joseph Rosen
Keyword(s):  
3D Imaging ◽  
Imaging System ◽  
Signal To Noise Ratio ◽  
Three Dimensional ◽  
Image Sensor ◽  
Two Dimensions ◽  
Imaging Systems ◽  
Coded Aperture ◽  
Axial Resolution ◽  
Point Spread

Abstract Interferenceless coded aperture correlation holography (I-COACH) is an incoherent digital holographic technique with lateral and axial resolution similar to a regular lens-based imaging system. The properties of I-COACH are dictated by the shape of the system’s point response termed point spread hologram (PSH). As previously shown, chaotic PSHs which are continuous over some area on the image sensor enable the system to perform three-dimensional (3D) holographic imaging. We also showed that a PSH of an ensemble of sparse dots improves the system’s signal-to-noise ratio (SNR) but reduces the dimensionality of the imaging from three to two dimensions. In this study, we test the midway shape of PSH, an ensemble of sparse islands distributed over the sensor plane. A PSH of isolated chaotic islands improves the SNR of the system compared to continuous chaotic PSH without losing the capability to perform 3D imaging. Reconstructed images of this new system are compared with images of continuous PSH, dot-based PSH, and direct images of a lens-based system. Visibility, SNR, and the product of visibility with SNR are the parameters used in the study. We also demonstrate the imaging capability of a system with partial annular apertures. The reconstruction results have better SNR and visibility than lens-based imaging systems with the same annular apertures.

Sign in / Sign up

Export Citation Format

Share Document