scholarly journals Utilization of Antibacterial Nanoparticles in Photocurable Additive Manufacturing of Advanced Composites for Improved Public Health

Polymers ◽  
2021 ◽  
Vol 13 (16) ◽  
pp. 2616
Author(s):  
Christopher Billings ◽  
Changjie Cai ◽  
Yingtao Liu
Keyword(s):  
Public Health ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Abrasion Resistance ◽  
Antimicrobial Properties ◽  
Digital Light Processing ◽  
Antimicrobial Function ◽  
3D Printed ◽  
Commercial Applications ◽  
Antibacterial Nanoparticles

This paper presents the additive manufacturing and characterization of nanoparticle-reinforced photocurable resin-based nanocomposites with a potential antimicrobial function for improved public health applications. Two types of photocurable resins are reinforced by titanium dioxide (TiO2) or zinc oxide (ZnO) nanoparticles with average diameters in the 10–30 nm range to provide antimicrobial properties. The developed nanocomposites can be additively manufactured using the digital light processing method with an outstanding surface quality and precise geometrical accuracy. Experimental characterizations are conducted to investigate key mechanical properties of the 3D printed nanocomposites, including Young’s Modulus, tensile strength, and abrasion resistance. Specimens produced were observed to demonstrate the following characteristics during testing. Tensile strength increased by 42.2% at a maximum value of 29.53 MPa. The modulus of elasticity increased by 14.3%, and abrasion resistance increased by 15.8%. The proper dispersion of the nanoparticles within the cured resin is validated by scanning electron images. The wettability and water absorption testing results indicate that the developed nanocomposites have an outstanding water resistance capability. The pairing of digital light processing with these novel nanocomposites allows for the creation of complex composite geometries that are not capable through other manufacturing processes. Therefore, they have the potential for long-term usage to improve general public health with antimicrobial functionality. The pairing of an unmodified photocurable resin with a 1% ZnO concentration demonstrated the most promise for commercial applications.

scholarly journals DLP 3D Printing Meets Lignocellulosic Biopolymers: Carboxymethyl Cellulose Inks for 3D Biocompatible Hydrogels

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1655 ◽  
Author(s):  
Giuseppe Melilli ◽  
Irene Carmagnola ◽  
Chiara Tonda-Turo ◽  
Fabrizio Pirri ◽  
Gianluca Ciardelli ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Carboxymethyl Cellulose ◽  
Biomedical Applications ◽  
Digital Light Processing ◽  
Chemically Modified ◽  
Significant Step ◽  
3D Printed ◽  
Biomedical Field

The development of new bio-based inks is a stringent request for the expansion of additive manufacturing towards the development of 3D-printed biocompatible hydrogels. Herein, methacrylated carboxymethyl cellulose (M-CMC) is investigated as a bio-based photocurable ink for digital light processing (DLP) 3D printing. CMC is chemically modified using methacrylic anhydride. Successful methacrylation is confirmed by 1H NMR and FTIR spectroscopy. Aqueous formulations based on M-CMC/lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP) photoinitiator and M-CMC/Dulbecco’s Modified Eagle Medium (DMEM)/LAP show high photoreactivity upon UV irradiation as confirmed by photorheology and FTIR. The same formulations can be easily 3D-printed through a DLP apparatus to produce 3D shaped hydrogels with excellent swelling ability and mechanical properties. Envisaging the application of the hydrogels in the biomedical field, cytotoxicity is also evaluated. The light-induced printing of cellulose-based hydrogels represents a significant step forward in the production of new DLP inks suitable for biomedical applications.

scholarly journals Superior Mechanical Behavior and Fretting Wear Resistance of 3D-Printed Inconel 625 Superalloy

2018 ◽  
Vol 8 (12) ◽  
pp. 2439 ◽  
Author(s):  
Yong Gao ◽  
Mingzhuo Zhou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Wear Resistance ◽  
Additive Manufacturing ◽  
High Hardness ◽  
Fretting Wear ◽  
Inconel 625 ◽  
3D Printed ◽  
Inconel 625 Superalloy ◽  
Electron Beam Selective Melting

Additive manufacturing (AM) nickel-based superalloys have been demonstrated to equate or exceed mechanical properties of cast and wrought counterparts but their tribological potentials have not been fully realized. This study investigates fretting wear behaviors of Inconel 625 against the 42 CrMo4 stainless steel under flat-on-flat contacts. Inconel 625 is prepared by additive manufacturing (AM) using the electron beam selective melting. Results show that it has a high hardness (335 HV), superior tensile strength (952 MPa) and yield strength (793 MPa). Tribological tests indicate that the AM-Inconel 625 can suppress wear of the surface within a depth of only ~2.4 μm at a contact load of 106 N after 2 × 104 cycles. The excellent wear resistance is attributed to the improved strength and the formation of continuous tribo-layers containing a mixture of Fe2O3, Fe3O4, Cr2O3 and Mn2O3.

scholarly journals Influence of printing direction on 3D printed ABS specimens

2020 ◽  
Vol 26 (3) ◽  
pp. 127-130
Author(s):  
Nassim Markiz ◽  
Eszter Horváth ◽  
Péter Ficzere
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Ultimate Tensile Strength ◽  
Modulus Of Elasticity ◽  
Tensile Tests ◽  
Standard Test ◽  
Complex Objects ◽  
3D Printed ◽  
Printing Direction

AbstractIn the recent years, additive manufacturing became an interesting topic in many fields due to the ease of manufacturing complex objects. However, it is impossible to determine the mechanical properties of any additive manufacturing parts without testing them. In this work, the mechanical properties with focus on ultimate tensile strength and modulus of elasticity of 3D printed acrylonitrile butadi-ene styrene (ABS) specimens were investigated. The tensile tests were carried using Zwick Z005 loading machine with a capacity of 5KN according to the American Society for Testing and Materials (ASTM) D638 standard test methods for tensile properties of plastics. The aim of this study is to investigate the influence of printing direction on the mechanical properties of the printed specimens. Thus, for each printing direction ( and ), five specimens were printed. Tensile testing of the 3D printed ABS specimens showed that the printing direction made the strongest specimen at an ultimate tensile strength of 22 MPa while at printing direction it showed 12 MPa. No influence on the modulus of elasticity was noticed. The experimental results are presented in the manuscript.

scholarly journals Comparison between Mechanical Properties and Structures of a Rolled and a 3D-Printed Stainless Steel

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3867 ◽  
Author(s):  
Stefano Natali ◽  
Andrea Brotzu ◽  
Daniela Pilone
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Additive Manufacturing ◽  
High Strength ◽  
Thin Sheets ◽  
Laser Melting ◽  
3D Printed ◽  
Lower Elongation ◽  
Manufacturing Technologies

In this work selective laser melting was successfully utilized to produce 316 stainless steel bulk specimens. Although this technology provides many advantages compared to conventional shaping processes, little residual porosity may be a problem for some applications where high strength is required. The objective of this work was to determine, through data analysis, a mechanical and metallographic comparison between thin sheets made by using different manufacturing technologies: Cold rolling and additive manufacturing. This comparison was useful to understand whether it could be more advantageous to use the prototyping for new mechanical components. The results show that the additive manufactured steel, due to its microstructure, is characterized by a higher yield strength and by a lower elongation and ultimate tensile strength.

scholarly journals Antimicrobial nanomaterials against biofilms: an alternative strategy

2017 ◽  
Vol 25 (2) ◽  
pp. 225-244 ◽  
Author(s):  
Chunhua Liu ◽  
Jing Guo ◽  
Xiaoqing Yan ◽  
Yongbing Tang ◽  
Asit Mazumder ◽  
...  
Keyword(s):  
Public Health ◽  
Antimicrobial Agent ◽  
Environmental Impacts ◽  
Environmental Conditions ◽  
Biofilm Formation ◽  
Antimicrobial Agents ◽  
Antimicrobial Properties ◽  
Industrial Sectors ◽  
Antimicrobial Function ◽  
Antibiofilm Agents

Microbial adhesion to surfaces and the consequent biofilm formation under various environmental conditions is a common ecological phenomenon. Although biofilms play crucial beneficial roles in many processes, they can also cause serious problems for food, biomedical, environmental, and industrial sectors, leading to higher costs of production and equipment maintenance, and negative public health and environmental impacts. Biofilms are difficult to eradicate due to their resistance to conventional antimicrobial applications. Consequently, attention has been devoted to new emerging nanomaterials for their remarkable antimicrobial function. Understanding the inactivation mechanisms is the key to increase the efficiency of nanoparticles (NPs) and enhance the feasibility of their application against various microorganisms under different environments. In this paper, we review the activities of NPs as antimicrobial agents. We also discuss the mechanisms and factors contributing to antimicrobial properties of NPs. In addition, we describe some of the approaches employing NPs as effective antimicrobial agent, and associated challenges and problems in developing NPs as effective antibiofilm agents.

scholarly journals 3D-printed self-healing hydrogels via Digital Light Processing

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Matteo Caprioli ◽  
Ignazio Roppolo ◽  
Annalisa Chiappone ◽  
Liraz Larush ◽  
Candido Fabrizio Pirri ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Room Temperature ◽  
Soft Robotics ◽  
Self Healing ◽  
Digital Light Processing ◽  
Initial Strength ◽  
Additive Manufacturing Technology ◽  
3D Printed ◽  
Living Tissues ◽  
Complex Architecture

AbstractSelf-healing hydrogels may mimic the behavior of living tissues, which can autonomously repair minor damages, and therefore have a high potential for application in biomedicine. So far, such hydrogels have been processed only via extrusion-based additive manufacturing technology, limited in freedom of design and resolution. Herein, we present 3D-printed hydrogel with self-healing ability, fabricated using only commercially available materials and a commercial Digital Light Processing printer. These hydrogels are based on a semi-interpenetrated polymeric network, enabling self-repair of the printed objects. The autonomous restoration occurs rapidly, at room temperature, and without any external trigger. After rejoining, the samples can withstand deformation and recovered 72% of their initial strength after 12 hours. The proposed approach enables 3D printing of self-healing hydrogels objects with complex architecture, paving the way for future applications in diverse fields, ranging from soft robotics to energy storage.

Tensile strength of 3D printed materials: Review and reassessment of test parameters

2018 ◽  
Vol 60 (7-8) ◽  
pp. 679-686 ◽  
Author(s):  
Jim Floor ◽  
Bas van Deursen ◽  
Erik Tempelman
Keyword(s):  
Tensile Strength ◽  
Test Parameters ◽  
3D Printed ◽  
Printed Materials

AM-Serienproduktion für die Automobilindustrie/AM series production for the automotive industry

2020 ◽  
Vol 110 (11-12) ◽  
pp. 752-757
Author(s):  
Lukas Weiser ◽  
Marco Batschkowski ◽  
Niclas Eschner ◽  
Benjamin Häfner ◽  
Ingo Neubauer ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Automotive Industry ◽  
Series Production ◽  
Production Scale ◽  
Additive Fertigung ◽  
Small Series ◽  
Start Up ◽  
3D Printed ◽  
Component Quality

Die additive Fertigung schafft neue Gestaltungsfreiheiten. Im Rahmen des Prototypenbaus und der Kleinserienproduktion kann das Verfahren des selektiven Laserschmelzens genutzt werden. Die Verwendung in der Serienproduktion ist bisher aufgrund unzureichender Bauteilqualität, langen Anlaufzeiten sowie mangelnder Automatisierung nicht im wirtschaftlichen Rahmen möglich. Das Projekt „ReAddi“ möchte eine erste prototypische Serienfertigung entwickeln, mit der additiv gefertigte Bauteile für die Automobilindustrie wirtschaftlich produziert werden können. Additive manufacturing (AM) offers new freedom of design. The selective laser-powderbed fusion (L-PBF) process can be used for prototyping and small series production. So far, it has not been economical to use it on a production scale due to insufficient component quality, long start-up times and a lack of automation. The project ReAddi aims to develop a first prototype series production to cost-effectively manufacture 3D-printed components for the automotive industry.

scholarly journals The Direct 3D Printing of Functional PEEK/Hydroxyapatite Composites via a Fused Filament Fabrication Approach

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 545
Author(s):  
Krzysztof Rodzeń ◽  
Preetam K. Sharma ◽  
Alistair McIlhagger ◽  
Mozaffar Mokhtari ◽  
Foram Dave ◽  
...  
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Selective Laser Sintering ◽  
Fused Filament Fabrication ◽  
Bone Apposition ◽  
Innovative Solutions ◽  
3D Printed ◽  
Work Samples ◽  
Viable Approach ◽  
Crystalline Domains

The manufacture of polyetheretherketone/hydroxyapatite (PEEK/HA) composites is seen as a viable approach to help enhance direct bone apposition in orthopaedic implants. A range of methods have been used to produce composites, including Selective Laser Sintering and injection moulding. Such techniques have drawbacks and lack flexibility to manufacture complex, custom-designed implants. 3D printing gets around many of the restraints and provides new opportunities for innovative solutions that are structurally suited to meet the needs of the patient. This work reports the direct 3D printing of extruded PEEK/HA composite filaments via a Fused Filament Fabrication (FFF) approach. In this work samples are 3D printed by a custom modified commercial printer Ultimaker 2+ (UM2+). SEM-EDX and µCT analyses show that HA particles are evenly distributed throughout the bulk and across the surface of the native 3D printed samples, with XRD highlighting up to 50% crystallinity and crystalline domains clearly observed in SEM and HR-TEM analyses. This highlights the favourable temperature conditions during 3D printing. The yield stress and ultimate tensile strength obtained for all the samples are comparable to human femoral cortical bone. The results show how FFF 3D printing of PEEK/HA composites up to 30 wt% HA can be achieved.

Sign in / Sign up

Export Citation Format

Share Document