scholarly journals Static and Dynamic Analysis of Cracked Concrete Beams Using Experimental Study and Finite Element Analysis

2017 ◽  
Author(s):  
Hamid Mazaheri ◽  
Hossein Rahami ◽  
Ali Kheyroddin
Keyword(s):  
Finite Element ◽  
Elastic Behavior ◽  
Finite Element Models ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Simple Method ◽  
Cracked Concrete ◽  
Static And Dynamic Analysis ◽  
Edge Cracks ◽  
Global Stiffness Matrix

In this paper, a simple method for defining the effects of cracks on elastic behavior of beam is presented. The cracked sections were modelled as rotational springs and the problem was solved using the finite element method. The global stiffness matrix of a beam with multiply cracked section was then assembled. For calculation of rotational spring stiffness equivalent to uncracked and cracked sections, finite element models and experimental test were used.The natural frequencies and mode shape of beams with multiple single-edge cracks were obtained and a new simple formula was proposed. Published numerical examples for cracked beams were used for validation.

scholarly journals Finite Element Analysis of the Multilayered Honeycomb Composite Material Subjected to Impact Loading

2017 ◽  
Vol 54 (1) ◽  
pp. 180-179 ◽  
Author(s):  
Raul Cormos ◽  
Horia Petrescu ◽  
Anton Hadar ◽  
Gorge Mihail Adir ◽  
Horia Gheorghiu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Composite Material ◽  
Experimental Testing ◽  
Finite Element Models ◽  
The Finite Element Method ◽  
Low Velocity ◽  
Element Analysis ◽  
Element Simulation ◽  
Different Levels

The main purpose of this paper is the study the behavior of four multilayered composite material configurations subjected to different levels of low velocity impacts, in the linear elastc domain of the materials, using experimental testing and finite element simulation. The experimental results obtained after testing, are used to validate the finite element models of the four composite multilayered honeycomb structures, which makes possible the study, using only the finite element method, of these composite materials for a give application.

scholarly journals Finite Element Analysis of Plate on Layered Tensionless Foundation

2010 ◽  
Vol 56 (3) ◽  
pp. 255-274 ◽  
Author(s):  
R. Buczkowski ◽  
W. Torbacki
Keyword(s):  
Finite Element ◽  
Thick Plate ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Contact Conditions ◽  
Interface Elements ◽  
Stiffness Matrices ◽  
Global Stiffness Matrix ◽  
Two Parameter ◽  
Tensionless Foundation

Abstract The method of calculations of a thick plate on the two-parameter layered foundation by the finite element method is presented. The numerical model allows to add a few (number of) foundation layers. The expressions for the element stiffness matrices of the foundation are based on 18-node zero-thickness interface elements. For modelling of thick plates the 9-node Mindlin element of the Lagrange family is used. The formulation of the problem takes into account the shear deformation of the plate and unilateral contact conditions between plate and foundation. The tensionless character of the foundation is achieved by removing from the global stiffness matrix the appropriate part of foundation stiffness attached to the node being in the separation stage. The advantages of the proposed algorithm are illustrated by numerical examples.

Impact of Helix and Taper on Structural Characteristics of a Nickel-Titanium Endodontic Instrument Through Finite Element Analysis

2006 ◽  
Author(s):  
Rui He ◽  
Charles J. Goodis ◽  
Jun Ni
Keyword(s):  
Finite Element ◽  
Mechanical Performance ◽  
Structural Characteristics ◽  
Sustainable Use ◽  
Nickel Titanium ◽  
Torsional Stiffness ◽  
Finite Element Models ◽  
The Finite Element Method ◽  
Clinical Practices ◽  
Element Analysis

The mechanical behavior of a rotary nickel-titanium endodontic instrument was evaluated through finite element models. Essential geometric features of blank taper and variable pitch were modeled and their impact on the mechanical performance of instruments was investigated. Simulation results showed that better bending flexibility and higher torsional stiffness can both be obtained on an instrument with a large helix configuration. The results also illustrated that the finite element method can be used to compute the critical load or deformation for the instrument which prompts the sustainable use of the instrument in clinical practices.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

A Finite Element Analysis of the General Rolling Contact Problem for a Viscoelastic Rubber Cylinder

1988 ◽  
Vol 16 (1) ◽  
pp. 18-43 ◽  
Author(s):  
J. T. Oden ◽  
T. L. Lin ◽  
J. M. Bass
Keyword(s):  
Finite Element ◽  
Variational Principles ◽  
Standing Waves ◽  
Rolling Contact ◽  
Finite Element Models ◽  
Viscoelastic Cylinder ◽  
Element Analysis ◽  
Elastic Rubber ◽  
Frictional Effects ◽  
Rough Foundation

Abstract Mathematical models of finite deformation of a rolling viscoelastic cylinder in contact with a rough foundation are developed in preparation for a general model for rolling tires. Variational principles and finite element models are derived. Numerical results are obtained for a variety of cases, including that of a pure elastic rubber cylinder, a viscoelastic cylinder, the development of standing waves, and frictional effects.

Tire Cornering Simulation Using an Explicit Finite Element Analysis Code

1998 ◽  
Vol 26 (2) ◽  
pp. 109-119 ◽  
Author(s):  
M. Koishi ◽  
K. Kabe ◽  
M. Shiratori
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Test System ◽  
Experimental Results ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Explicit Finite Element ◽  
Explicit Finite Element Analysis ◽  
Element Method

Abstract The finite element method has been used widely in tire engineering. Most tire simulations using the finite element method are static analyses, because tires are very complex nonlinear structures. Recently, transient phenomena have been studied with explicit finite element analysis codes. In this paper, the authors demonstrate the feasibility of tire cornering simulation using an explicit finite element code, PAM-SHOCK. First, we propose the cornering simulation using the explicit finite element analysis code. To demonstrate the efficiency of the proposed simulation, computed cornering forces for a 175SR14 tire are compared with experimental results from an MTS Flat-Trac Tire Test System. The computed cornering forces agree well with experimental results. After that, parametric studies are conducted by using the proposed simulation.

scholarly journals The biomechanical effect on the adjacent L4/L5 segment of S1 superior facet arthroplasty: a finite element analysis for the male spine

2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Zewen Shi ◽  
Lin Shi ◽  
Xianjun Chen ◽  
Jiangtao Liu ◽  
Haihao Wu ◽  
...  
Keyword(s):  
Finite Element ◽  
Range Of Motion ◽  
Facet Joint ◽  
Adjacent Segment ◽  
Finite Element Models ◽  
Level Of Evidence ◽  
Element Analysis ◽  
Flexion Extension ◽  
Biomechanical Effect ◽  
Lumbar Range Of Motion

Abstract Background The superior facet arthroplasty is important for intervertebral foramen microscopy. To our knowledge, there is no study about the postoperative biomechanics of adjacent L4/L5 segments after different methods of S1 superior facet arthroplasty. To evaluate the effect of S1 superior facet arthroplasty on lumbar range of motion and disc stress of adjacent segment (L4/L5) under the intervertebral foraminoplasty. Methods Eight finite element models (FEMs) of lumbosacral vertebrae (L4/S) had been established and validated. The S1 superior facet arthroplasty was simulated with different methods. Then, the models were imported into Nastran software after optimization; 500 N preload was imposed on the L4 superior endplate, and 10 N⋅m was given to simulate flexion, extension, lateral flexion and rotation. The range of motion (ROM) and intervertebral disc stress of the L4-L5 spine were recorded. Results The ROM and disc stress of L4/L5 increased with the increasing of the proportions of S1 superior facet arthroplasty. Compared with the normal model, the ROM of L4/L5 significantly increased in most directions of motion when S1 superior facet formed greater than 3/5 from the ventral to the dorsal or 2/5 from the apex to the base. The disc stress of L4/L5 significantly increased in most directions of motion when S1 superior facet formed greater than 3/5 from the ventral to the dorsal or 1/5 from the apex to the base. Conclusion In this study, the ROM and disc stress of L4/L5 were affected by the unilateral S1 superior facet arthroplasty. It is suggested that the forming range from the ventral to the dorsal should be less than 3/5 of the S1 upper facet joint. It is not recommended to form from apex to base. Level of evidence Level IV

scholarly journals 3D Finite Element Analysis of Rotary Instruments in Root Canal Dentine with Different Elastic Moduli

2021 ◽  
Vol 11 (6) ◽  
pp. 2547 ◽  
Author(s):  
Carlo Prati ◽  
João Paulo Mendes Tribst ◽  
Amanda Maria de Oliveira Dal Piva ◽  
Alexandre Luiz Souto Borges ◽  
Maurizio Ventre ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Root Canal ◽  
Elastic Moduli ◽  
Reaction Force ◽  
Von Mises Stress ◽  
Elastic Behavior ◽  
Element Analysis ◽  
Heat Treated ◽  
Von Mises

The aim of the present investigation was to calculate the stress distribution generated in the root dentine canal during mechanical rotation of five different NiTi endodontic instruments by means of a finite element analysis (FEA). Two conventional alloy NiTi instruments F360 25/04 and F6 Skytaper 25/06, in comparison to three heat treated alloys NiTI Hyflex CM 25/04, Protaper Next 25/06 and One Curve 25/06 were considered and analyzed. The instruments’ flexibility (reaction force) and geometrical features (cross section, conicity) were previously investigated. For each instrument, dentine root canals with two different elastic moduli(18 and 42 GPa) were simulated with defined apical ratios. Ten different CAD instrument models were created and their mechanical behaviors were analyzed by a 3D-FEA. Static structural analyses were performed with a non-failure condition, since a linear elastic behavior was assumed for all components. All the instruments generated a stress area concentration in correspondence to the root canal curvature at approx. 7 mm from the apex. The maximum values were found when instruments were analyzed in the highest elastic modulus dentine canal. Strain and von Mises stress patterns showed a higher concentration in the first part of curved radius of all the instruments. Conventional Ni-Ti endodontic instruments demonstrated higher stress magnitudes, regardless of the conicity of 4% and 6%, and they showed the highest von Mises stress values in sound, as well as in mineralized dentine canals. Heat-treated endodontic instruments with higher flexibility values showed a reduced stress concentration map. Hyflex CM 25/04 displayed the lowest von Mises stress values of, respectively, 35.73 and 44.30 GPa for sound and mineralized dentine. The mechanical behavior of all rotary endodontic instruments was influenced by the different elastic moduli and by the dentine canal rigidity.

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

Sign in / Sign up

Export Citation Format

Share Document