Subsurface iron and arsenic removal: low-cost technology for community-based water supply in Bangladesh

2010 ◽  
Vol 62 (11) ◽  
pp. 2702-2709 ◽  
Author(s):  
D. van Halem ◽  
S. G. J. Heijman ◽  
R. Johnston ◽  
I. M. Huq ◽  
S. K. Ghosh ◽  
...  

The principle of subsurface or in situ iron and arsenic removal is that aerated water is periodically injected into an anoxic aquifer through a tube well, displacing groundwater containing Fe(II). An oxidation zone is created around the tube well where Fe(II) is oxidised. The freshly formed iron hydroxide surfaces provide new sorption sites for soluble Fe(II) and arsenic. The system's efficiency is determined based on the ratio between abstracted volume with reduced iron/arsenic concentrations (V) and the injected volume (Vi). In the field study presented in this paper, the small-scale application of this technology was investigated in rural Bangladesh. It was found that at small injection volumes (<1 m3) iron removal was successful and became more effective with every successive cycle. For arsenic, however, the system did not prove to be very effective yet. Arsenic retardation was only limited and breakthrough of 10 μg/L (WHO guideline) was observed before V/Vi=1, which corresponds to arrival of groundwater at the well. Possible explanations for insufficient arsenic adsorption are the short contact times within the oxidation zone, and the presence of competing anions, like phosphate.

2017 ◽  
Vol 17 (5) ◽  
pp. 1249-1259 ◽  
Author(s):  
Nao Kamei-Ishikawa ◽  
Nami Segawa ◽  
Daisuke Yamazaki ◽  
Ayumi Ito ◽  
Teruyuki Umita

The down-flow hanging sponge (DHS) reactor was used for continuous As removal treatment of As-contaminated water. The treatment scheme was: (1) As(III) in contaminated water is oxidized by arsenite-oxidizing bacteria fixed in the sponges in the reactor; (2) Fe(II) naturally existing in the water is oxidized by dissolved oxygen; (3) Fe(III) is precipitated as iron hydroxide and As(V) is co-precipitated with the iron hydroxide; and finally (4) the co-precipitates are fixed in the sponges. This system could remove As from As-contaminated water on a small scale and at low cost. The results showed that, after using the DHS reactor, As and Fe concentrations in the treated water were lower than water quality standards for drinking water when Fe(II) concentration in the influent was lower than 10 mg/L and the Fe/As ratio was higher than 6.67–8.42, with dependence on the Fe concentration. Additionally, even if Fe concentration is higher than 10 mg/L, the treatment system is still applicable if the pH of the influent is higher than 7 or the retention time is longer than 2 h.


Water ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2520
Author(s):  
Jasmina Nikić ◽  
Aleksandra Tubić ◽  
Malcolm Watson ◽  
Snežana Maletić ◽  
Marko Šolić ◽  
...  

Magnetite nanoparticles were synthesized by a simple and ecofriendly method using onion peel (MNp-OP) and corn silk extract (MNp-CS), in order to develop new low-cost adsorbents for arsenic removal from groundwater. As a point of comparison, magnetite nanoparticles were also synthesized with a conventional chemical process (MNp-CO). The antioxidant potential of onion peel and corn silk extracts was determined using ferric reducing antioxidant power (FRAP) and free radical (DPPH) scavenging assays, including the total phenolics, flavonoids and tannins contents. The synthesized magnetite nanoparticles were characterised using different techniques (Scanning electron microscope/Energy dispersive spectroscopy (SEM/EDS), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR) and Brunauer-Emmett-Teller (BET) surface area analyzer). The adsorption capacity of MNp-OP and MNp-CS and the arsenic removal mechanism of these novel adsorbents was investigated through kinetic and equilibrium experiments and their corresponding mathematical models. Characterisation of MNp-OP and MNp-CS shows high BET specific surface areas of 243 m2/g and 261 m2/g, respectively. XRD and FTIR analysis confirmed the formation and presence of magnetite nanoparticles. The arsenic adsorption mechanism on MNp-OP, MNp-CS and MNp-CO involves chemisorption, intraparticle and external diffusion. Maximal adsorption capacities of MNp-OP, MNp-CS and MNp-CO were 1.86, 2.79, and 1.30 mg/g respectively. The green synthesis applied using onion peel and corn silk extracts was cost effective and environmentally friendly, and results in adsorbents with a high capacity for arsenic and magnetic properties, making them a very promising alternative approach in the treatment of arsenic contaminated groundwater.


2008 ◽  
Vol 58 (10) ◽  
pp. 2009-2015 ◽  
Author(s):  
U. Rott ◽  
H. Kauffmann

Arsenic in groundwater is a huge problem in numerous regions of the world. Many people are exposed to high arsenic concentrations and consequently risk getting ill or even die as a result of arsenic poisoning. There are several efficient technologies for the removal of arsenic but often these methods have disadvantages, e.g. high costs for installation and/or operation, the need for chemicals or the production of arsenic contaminated filter sludge. These disadvantages can make the application difficult, especially in poor regions. Under suitable ancillary conditions the subterranean (in-situ) treatment, which is often used for iron and manganese removal from groundwater, can also be applied for the removal of arsenic and can be a cost-effective treatment technology. A field trial was carried out with a low-cost in-situ treatment plant in West Bengal/India which is described in this paper, in order to investigate whether this treatment technology is also applicable under the boundary conditions there. As for the in-situ treatment technology besides oxygen no additives are required and no arsenic contaminated filter sludge is produced this technology could be a suitable method for arsenic removal especially in poor regions.


2006 ◽  
Vol 41 (2) ◽  
pp. 171-184 ◽  
Author(s):  
Paul Westerhoff ◽  
Michelle De Haan ◽  
Alan Martindale ◽  
Mohammad Badruzzaman

Abstract More stringent arsenic regulations are requiring water utilities of all sizes to install treatment systems on wells which historically only had chlorination. A case study is presented for evaluating arsenic adsorption media at a well site in Mesa, Arizona, but the approach and methodological conclusions are transferable to any arsenic treatment system. The goal of this project is to develop a comprehensive, cost-effective and rapid approach for selecting arsenic adsorptive media. Batch laboratory tests, labscale continuous flow column tests and pilot-scale tests were conducted to evaluate removal efficiency, robustness, operational benefits and cost effectiveness of eight different commercially available adsorbents. Batch tests conducted at multiple pH levels provided limited benefit when compared against continuous flow rapid small-scale column tests (RSSCTs) to evaluate arsenic removal capability by different media. Breakthrough curves of arsenic, vanadium, silica and other trace metals corresponded well between lab-scale RSSCT and field-based pilot scale, suggesting that RSSCTs offer a timesaving approach for adsorptive media selection. Leaching tests on spent media verified that media could be safely disposed and high-resolution microscopic analysis indicated that calcium and silica accumulate on media surfaces and affect the longevity of arsenic removal systems.


2013 ◽  
Vol 14 (1) ◽  
pp. 119-126 ◽  
Author(s):  
S. C. Borges Freitas ◽  
D. van Halem ◽  
M. M. Rahman ◽  
J. Q. J. C. Verberk ◽  
A. B. M. Badruzzaman ◽  
...  

Hand-pump subsurface arsenic removal (SAR) has been investigated in rural Bangladesh with different groundwater conditions and intermittent operation modes. Multiple injection-abstraction cycles were performed after injection of 1 m3 of aerated water. From these experiments it can be concluded that hand-pump SAR, in the traditional injection-abstraction design, does not provide drinking water below the WHO arsenic guideline of 10 μg/L. Results show that arsenic removal was not enhanced by: (i) injection of O2-rich water, (ii) higher Fe:As ratios in the groundwater, or by (iii) multiple injection-abstraction cycles, i.e. at location 1, the breakthrough occurred at abstraction-injection ratios of Va/Vi = 2, for cycle 23. It is proposed that dissolved organic carbon (DOC), bicarbonate and phosphate have a significant effect on the arsenic adsorption process. However, iron removal was very efficient and abstraction-injection ratios increased within successive cycles, with Va/Vi > 8 for cycle 23. Furthermore, intermittent operation reduced arsenic concentrations after stop and restart, suggesting insufficient contact time between soluble arsenic and oxidized iron surfaces around the tube well.


Author(s):  
Xudong Tang ◽  
Chanwoo Park

Two-phase thermal management technologies are promising cooling solutions for the high performance electronics in the next generation military and commercial vehicles. However, vibrations (∼ 10Grms in commercial automobile engines and transmissions) and shocks (30G to 1,200G in military combat vehicles, caused by gun firing, ballistic launch and abrupt maneuvering) present a severe challenge to any capillary-driven (i.e., passive) two-phase devices. A low-cost, vibration/shock-tolerant Capillary Two-Phase Loop (CTPL) technology was developed as a cooling alternative for the future military vehicles. Unlike the traditional two-phase cooling loops such as Loop Heat Pipes (LHP) and Capillary Pumped Loops (CPL), the CTPL offers the following advantages: (1) lower manufacturing cost by sintering the evaporator wick in-situ; (2) improved tolerance to vibrations and shocks due to the improved mechanical strengths of the in-situ sintered wick; (3) improved heat flux performance because of the non-inverted meniscus wick. Small-scale proof-to-concept CTPL prototypes were successfully tested up to 120W of heat input and under multiple, consecutive shocks of up to 6.6G.


2013 ◽  
Vol 13 (2) ◽  
pp. 319-327
Author(s):  
M. Velasco-Perez ◽  
K. M. Hiscock

This paper addresses the development of low-cost adsorbents for removal of arsenic from water in support of mitigation programmes in low and middle income countries. Activated carbon (AC) is a well established water treatment technology, but has high cost and low selectivity in respect of arsenic. AC made from agricultural by-products is a low-cost alternative to coal-based AC. In this study, the preparation parameters of sugar-cane activated carbon (SCAC) were optimised for arsenic(V) and arsenic(III) adsorption. The effect of preparation parameters on arsenic removal was investigated with a 23 factorial experiment. SCAC was characterised by the pH of zero charge, surface area, pore width distribution, particle size distribution and imaging under scanning electron microscopy. Activation temperature (AT) has a profound effect on arsenic adsorption; arsenic(V) adsorption increased from 2.8% at an AT of 873 K to 87.6% at an AT of 1,173 K. The percentage of arsenic removal from water has a strong positive correlation with surface area, and a strong negative correlation with micropore/pore volume ratio and the percentage in volume of particles with a size of 60–2,000 μm. In conclusion, this research shows that low-cost AC can be manufactured for removal of target pollutants, such as arsenic, from water.


Author(s):  
Jian-Shing Luo ◽  
Hsiu Ting Lee

Abstract Several methods are used to invert samples 180 deg in a dual beam focused ion beam (FIB) system for backside milling by a specific in-situ lift out system or stages. However, most of those methods occupied too much time on FIB systems or requires a specific in-situ lift out system. This paper provides a novel transmission electron microscopy (TEM) sample preparation method to eliminate the curtain effect completely by a combination of backside milling and sample dicing with low cost and less FIB time. The procedures of the TEM pre-thinned sample preparation method using a combination of sample dicing and backside milling are described step by step. From the analysis results, the method has applied successfully to eliminate the curtain effect of dual beam FIB TEM samples for both random and site specific addresses.


2019 ◽  
Vol 70 (7) ◽  
pp. 2330-2334
Author(s):  
Mihaela Ciopec ◽  
Adina Negrea ◽  
Narcis Duteanu ◽  
Corneliu Mircea Davidescu ◽  
Iosif Hulka ◽  
...  

Arsenic content in groundwater�s present a wide range of concentration, ranging from hundreds of micrograms to thousands of micrograms of arsenic per litter, while the maximum permitted arsenic concentration established by World Health Organization (WHO) is 10 mg L-1. According to the WHO all people, regardless of their stage of development and their social economic condition, have the right to have access to adequate drinking water. The most efficient and economic technique used for arsenic removal is represented by adsorption. In order to make this remediation technique more affordable and environmentally friendly is important to new materials with advance adsorbent properties. Novelty of present paper is represented by the usage of a new adsorbent material obtained by physical - chemical modification of Amberlite XAD polymers using crown ethers followed by iron doping, due to well-known affinity of arsenic for iron ions. Present paper aims to test the obtained modified Amberlite polymer for arsenic removal from real groundwater by using adsorption in a fixed bed column, establishing in this way a mechanism for the adsorption process. During experimental work was studied the influence of competing ions from real water into the arsenic adsorption process.


2019 ◽  
Author(s):  
Nikki Theofanopoulou ◽  
Katherine Isbister ◽  
Julian Edbrooke-Childs ◽  
Petr Slovák

BACKGROUND A common challenge within psychiatry and prevention science more broadly is the lack of effective, engaging, and scale-able mechanisms to deliver psycho-social interventions for children, especially beyond in-person therapeutic or school-based contexts. Although digital technology has the potential to address these issues, existing research on technology-enabled interventions for families remains limited. OBJECTIVE The aim of this pilot study was to examine the feasibility of in-situ deployments of a low-cost, bespoke prototype, which has been designed to support children’s in-the-moment emotion regulation efforts. This prototype instantiates a novel intervention model that aims to address the existing limitations by delivering the intervention through an interactive object (a ‘smart toy’) sent home with the child, without any prior training necessary for either the child or their carer. This pilot study examined (i) engagement and acceptability of the device in the homes during 1 week deployments; and (ii) qualitative indicators of emotion regulation effects, as reported by parents and children. METHODS In this qualitative study, ten families (altogether 11 children aged 6-10 years) were recruited from three under-privileged communities in the UK. The RA visited participants in their homes to give children the ‘smart toy’ and conduct a semi-structured interview with at least one parent from each family. Children were given the prototype, a discovery book, and a simple digital camera to keep at home for 7-8 days, after which we interviewed each child and their parent about their experience. Thematic analysis guided the identification and organisation of common themes and patterns across the dataset. In addition, the prototypes automatically logged every interaction with the toy throughout the week-long deployments. RESULTS Across all 10 families, parents and children reported that the ‘smart toy’ was incorporated into children’s emotion regulation practices and engaged with naturally in moments children wanted to relax or calm down. Data suggests that children interacted with the toy throughout the duration of the deployment, found the experience enjoyable, and all requested to keep the toy longer. Child emotional connection to the toy—caring for its ‘well-being’—appears to have driven this strong engagement. Parents reported satisfaction with and acceptability of the toy. CONCLUSIONS This is the first known study investigation of the use of object-enabled intervention delivery to support emotion regulation in-situ. The strong engagement and qualitative indications of effects are promising – children were able to use the prototype without any training and incorporated it into their emotion regulation practices during daily challenges. Future work is needed to extend this indicative data with efficacy studies examining the psychological efficacy of the proposed intervention. More broadly, our findings suggest the potential of a technology-enabled shift in how prevention interventions are designed and delivered: empowering children and parents through ‘child-led, situated interventions’, where participants learn through actionable support directly within family life, as opposed to didactic in-person workshops and a subsequent skills application.


Sign in / Sign up

Export Citation Format

Share Document