Structure-Property Correlation in Low K Dielectric Materials

1999 ◽  
Vol 565 ◽  
Author(s):  
Michael Morgen ◽  
Jie-Hua Zhao ◽  
Michael Hay ◽  
Taiheui Cho ◽  
Paul S. Ho
Keyword(s):  
Dielectric Constant ◽  
Mechanical Stability ◽  
Process Integration ◽  
Dielectric Materials ◽  
Thermomechanical Properties ◽  
Low Dielectric Constant ◽  
Structure Property ◽  
Material Development ◽  
Low Dielectric ◽  
Low K

AbstractIn recent years there have been widespread efforts to identify low dielectric constant materials that can satisfy a number of diverse performance requirements necessary for successful integration into IC devices. This has led to extensive efforts to develop low k materials and the associated process integration. A particularly difficult challenge for material development has been to find the combination of low dielectric constant and good thermal and mechanical stability. In this paper recent characterization results for low k materials performed at the University of Texas will be reviewed, with an emphasis on the relationship of chemical structure to the aforementioned key material properties. For example, measurements showing the effect of film porosity on dielectric constant and thermal and mechanical properties is presented. This data, as well as that for other material types, demonstrates the tradeoffs between dielectric constant and thermomechanical properties that are often made during the course of material development.

Low Dielectric Constant Materials for IC Intermetal Dielectric Applications: A Status Report on the Leading Candidates

1996 ◽  
Vol 443 ◽  
Author(s):  
Neil H. Hendricks
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Process Integration ◽  
Electrical Performance ◽  
Low Dielectric Constant ◽  
Status Report ◽  
Structure Property ◽  
Chemical Structures ◽  
Low Dielectric ◽  
Low Dielectric Constant Materials

AbstractFor over two years, intensive efforts at SEMATECH and elsewhere have focused on identifying low dielectric constant (low ε) materials which possess all of the required properties and processing characteristics needed for integration into standard IC fabrication lines. To date, no material candidate has been shown to satisfy this impressive list of requirements. For some candidates, drawbacks related to material properties such as poor thermal stability or electrical performance have been identified; in other cases, problems in process integration, for example difficulties in patterning have stalled progress.In this paper, most of the current leading candidates for the low ε IC IMC application are identified and discussed. An attempt is made to correlate structure/property relationships in these materials with their relative attributes and deficiencies as they relate to the IMD application. Key differences in chemistry and property/processing characteristics are contrasted for low c silicon-oxygen polymers and for purely organic polymers. Novel dielectrics such as porous organic and inorganic thin films are also discussed in terms of their properties and associated process integration challenges. Since the needs for global planarization and low c IMD are occurring within roughly the same generation of minimum feature size (˜ 0.25 μm), the chemical mechanical polishing (CMP) of low dielectric constant thin films and/or of SiO2 layers deposited above them is briefly discussed. Both subtractive metalization and damascene processes are included, and the required low dielectric constant film properties and processing characteristics are contrasted for each process. Finally, the author's views on future trends in low dielectric constant materials development are presented, with an emphasis on identifying the types of chemical structures which may prove viable for this most demanding of all polymer film applications.

Novel Materials as Interlayer Low-K Dielectrics for CMOS Interconnect Applications

2011 ◽  
Vol 110-116 ◽  
pp. 5380-5383
Author(s):  
Tejas R. Naik ◽  
Veena R. Naik ◽  
Nisha P. Sarwade
Keyword(s):  
Dielectric Constant ◽  
Integrated Circuits ◽  
Dielectric Materials ◽  
Low Dielectric Constant ◽  
Interlayer Dielectric ◽  
Novel Materials ◽  
Low Dielectric ◽  
Processing Properties ◽  
New Generation ◽  
Low K

Scaling down the integrated circuits has resulted in the arousal of number of problems like interaction between interconnect, crosstalk, time delay etc. These problems can be overcome by new designs and by use of corresponding novel materials, which may be a solution to these problems. In the present paper we try to put forward very recent development in the use of novel materials as interlayer dielectrics (ILDs) having low dielectric constant (k) for CMOS interconnects. The materials presented here are porous and hybrid organo-inorganic new generation interlayer dielectric materials possessing low dielectric constant and better processing properties.

Integration Issues for Low Dielectric Constant Materials in each Generation of ULSI'S

1999 ◽  
Vol 565 ◽  
Author(s):  
Hideki Gomi ◽  
Koji Kishimoto ◽  
Tatsuya Usami ◽  
Ken-ichi Koyanagi ◽  
Takashi Yokoyama ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Silicon Oxide ◽  
Process Integration ◽  
Low Dielectric Constant ◽  
Next Generation ◽  
Hydrogen Silsesquioxane ◽  
Low Dielectric ◽  
Low Dielectric Constant Materials ◽  
Fluorinated Silicon Oxide ◽  
Low K

AbstractThe technologies utilizing Fluorinated Silicon Oxide (FSG, k=3.6) and Hydrogen Silsesquioxane (HSQ, k=3.0) have been established for 0.25-μm and 0.18-μm generation ULSIs. However, low-k materials for the next generation ULSIs, which have a dielectric constant of less than 3.0, have not become mature yet. In this paper, we review process integration issues in applying FSG and HSQ, and describe integration results and device performance using Fluorinated Amorphous Carbon (a-C:F, k=2.5) as one of the promising low-k materials for the next generation ULSIs.

Integration Issues for Low Dielectric Constant Materials in each Generation of ULSI's

1999 ◽  
Vol 564 ◽  
Author(s):  
Hideki Gomi ◽  
Koji Kishimoto ◽  
Tatsuya Usami ◽  
Ken-ichi Koyanagi ◽  
Takashi Yokoyama ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Silicon Oxide ◽  
Process Integration ◽  
Low Dielectric Constant ◽  
Next Generation ◽  
Hydrogen Silsesquioxane ◽  
Low Dielectric ◽  
Low Dielectric Constant Materials ◽  
Fluorinated Silicon Oxide ◽  
Low K

AbstractThe technologies utilizing Fluorinated Silicon Oxide (FSG, k=3.6) and Hydrogen Silsesquioxane (HSQ, k=3.0) have been established for 0.25-µm and 0.1 8-µm generation ULSIs. However, low-k materials for the next generation ULSIs, which have a dielectric constant of less than 3.0, have not become mature yet. In this paper, we review process integration issues in applying FSG and HSQ, and describe integration results and device performance using Fluorinated Amorphous Carbon (a-C:F, k=2.5) as one of the promising low-k materials for the next generation ULSIs.

Structire, Properties, and Process Characteristics of Low-K Materials Prepared by PECVD

1999 ◽  
Vol 565 ◽  
Author(s):  
Y. Shimogaki ◽  
S. W. Lim ◽  
E. G. Loh ◽  
Y. Nakano ◽  
K. Tada ◽  
...  
Keyword(s):  
Growth Rate ◽  
Dielectric Constant ◽  
Gas Flow ◽  
Structural Changes ◽  
Silicon Oxide ◽  
Reactive Species ◽  
Low Dielectric Constant ◽  
Low Dielectric ◽  
Step Coverage ◽  
Low K

AbstractLow dielectric constant F-doped silicon oxide films (SiO:F) can be prepared by adding fluorine source, like as CF4 to the conventional PECVD processes. We could obtain SiO:F films with dielectric constant as low as 2.6 from the reaction mixture of SiH4/N2 O/CF4. The structural changes of the oxides were sensitively detected by Raman spectroscopy. The three-fold ring and network structure of the silicon oxides were selectively decreased by adding fluorine into the film. These structural changes contribute to the decrease ionic polarization of the film, but it was not the major factor for the low dielectric constant. The addition of fluorine was very effective to eliminate the Si-OH in the film and the disappearance of the Si-OH was the key factor to obtain low dielectric constant. A kinetic analysis of the process was also performed to investigate the reaction mechanism. We focused on the effect of gas flow rate, i.e. the residence time of the precursors in the reactor, on growth rate and step coverage of SiO:F films. It revealed that there exists two species to form SiO:F films. One is the reactive species which contributes to increase the growth rate and the other one is the less reactive species which contributes to have uniform step coverage. The same approach was made on the PECVD process to produce low-k C:F films from C2F4, and we found ionic species is the main precursor to form C:F films.

The characterization and preparation of porous low dielectric films using various cyclodextrins as template materials

2003 ◽  
Vol 766 ◽  
Author(s):  
Jin-Heong Yim ◽  
Jung-Bae Kim ◽  
Hyun-Dam Jeong ◽  
Yi-Yeoul Lyu ◽  
Sang Kook Mah ◽  
...  
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Dielectric Constant ◽  
Pore Structure ◽  
Pore Diameter ◽  
Dielectric Films ◽  
Low Dielectric Constant ◽  
Cyclodextrin Derivatives ◽  
Low Dielectric ◽  
Low K

AbstractPorous low dielectric films containing nano pores (∼20Å) with low dielectric constant (<2.2), have been prepared by using various kinds of cyclodextrin derivatives as porogenic materials. The pore structure such as pore size and interconnectivity can be controlled by changing functional groups of the cyclodextrin derivatives. We found that mechanical properties of porous low-k thin film prepared with mCSSQ (modified cyclic silsesquioxane) precursor and cyclodextrin derivatives were correlated with the pore interconnection length. The longer the interconnection length of nanopores in the thin film, the worse the mechanical properties of the thin film (such as hardness and modulus) even though the pore diameter of the films were microporous (∼2nm).

Intrinsic low dielectric behaviour of a highly thermally stable Sr-based metal–organic framework for interlayer dielectric materials

2014 ◽  
Vol 2 (19) ◽  
pp. 3762-3768 ◽  
Author(s):  
Muhammad Usman ◽  
Cheng-Hua Lee ◽  
Dung-Shing Hung ◽  
Shang-Fan Lee ◽  
Chih-Chieh Wang ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Metal Organic Framework ◽  
Dielectric Materials ◽  
Low Dielectric Constant ◽  
Water Molecules ◽  
Compound A ◽  
Interlayer Dielectric ◽  
Low Dielectric ◽  
Metal Organic ◽  
Organic Framework

A Sr-based metal–organic framework exhibits an intrinsic low dielectric constant after removing the water molecules. A low dielectric constant and high thermal stability make this compound a candidate for use as a low-k material.

Robust spin-on-glass poly(methyl)silsesquioxane-based low-k materials derived from a cyclic siloxane precursor

RSC Advances ◽  
2015 ◽  
Vol 5 (82) ◽  
pp. 66511-66517 ◽  
Author(s):  
Albert S. Lee ◽  
Sung Yeoun Oh ◽  
Seung-Sock Choi ◽  
He Seung Lee ◽  
Seung Sang Hwang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Dielectric Constant ◽  
Low Dielectric Constant ◽  
Cyclic Siloxane ◽  
Low Dielectric ◽  
Methyl Silsesquioxane ◽  
Low K

Low dielectric constant poly(methyl)silsesquioxane spin-on-glass resins incorporating a cyclic precursor exhibited exceptional mechanical properties to withstand CMP processes.

Siloxane Polymers as Low Dielectric Materials for Microelectronics

1995 ◽  
Vol 390 ◽  
Author(s):  
C. P. Wong
Keyword(s):  
Dielectric Constant ◽  
Three Dimensional ◽  
Signal Propagation ◽  
Dielectric Materials ◽  
Propagation Delay ◽  
Dimensional Structure ◽  
Low Dielectric Constant ◽  
Interlayer Dielectric ◽  
Low Dielectric ◽  
High Dielectric

ABSTRACTA modem VLSI device is a complicated three-dimensional structure that consists of multilayer metallization conductor lines which are separated with interlayer-dielectrics as insulation. This VLSI technology drives the IC device into sub-micron feature size that operates at ultra-fast speed (in excess of > 100 MHz). Passivation and interlayer dielectric materials are critical to the device performance due to the conductor signal propagation delay of the high dielectric constant of the material. Low dielectric constant materials are the preferred choice of materials for this reasons. These materials, such as Teflon® and siloxanes (silicones), are desirable because of their low dielectric constant (∈1) = 2.0, 2.7, respectively. This paper describes the use of a low dielectric constant siloxane polymer (silicone) as IC devices passivation layer material, its chemistry, material processes and reliability testing.

Chemical-Mechanical Planarization of Low-k Polymers for Advanced IC Structures

2002 ◽  
Vol 124 (4) ◽  
pp. 362-366 ◽  
Author(s):  
Christopher L. Borst ◽  
Dipto G. Thakurta ◽  
William N. Gill ◽  
Ronald J. Gutmann
Keyword(s):  
Dielectric Constant ◽  
Surface Chemistry ◽  
Chemical Mechanical Planarization ◽  
Low Dielectric Constant ◽  
Chemical Company ◽  
Low Dielectric ◽  
Scale Models ◽  
Physically Based ◽  
Thickness Measurements ◽  
Low K

Successful integration of copper and low dielectric constant (low-k) materials is dependent on robust chemical-mechanical planarization (CMP) during damascene patterning. This process includes the direct removal of copper and interaction of the copper slurry with the underlying dielectric. Experiments were designed and performed to examine the CMP of two low-k polymers from Dow Chemical Company, bis-benzocyclobutene (BCB*, k=2.65) and “silicon-application low-k material” (SiLK* resin, k=2.65) with both acidic slurries suitable for copper damascene patterning and a KH phthalate-based model slurry developed for SiLK. Blanket polymer films were polished in order to determine the interactions that occur when copper and liner materials are removed by the damascene CMP process. Removal rates were obtained from material thickness measurements, post-CMP surface topography from AFM scans, and post-CMP surface chemistry from XPS measurements. Physically based wafer-scale models are presented which are compatible with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document