Structire, Properties, and Process Characteristics of Low-K Materials Prepared by PECVD

1999 ◽  
Vol 565 ◽  
Author(s):  
Y. Shimogaki ◽  
S. W. Lim ◽  
E. G. Loh ◽  
Y. Nakano ◽  
K. Tada ◽  
...  
Keyword(s):  
Growth Rate ◽  
Dielectric Constant ◽  
Gas Flow ◽  
Structural Changes ◽  
Silicon Oxide ◽  
Reactive Species ◽  
Low Dielectric Constant ◽  
Low Dielectric ◽  
Step Coverage ◽  
Low K

AbstractLow dielectric constant F-doped silicon oxide films (SiO:F) can be prepared by adding fluorine source, like as CF4 to the conventional PECVD processes. We could obtain SiO:F films with dielectric constant as low as 2.6 from the reaction mixture of SiH4/N2 O/CF4. The structural changes of the oxides were sensitively detected by Raman spectroscopy. The three-fold ring and network structure of the silicon oxides were selectively decreased by adding fluorine into the film. These structural changes contribute to the decrease ionic polarization of the film, but it was not the major factor for the low dielectric constant. The addition of fluorine was very effective to eliminate the Si-OH in the film and the disappearance of the Si-OH was the key factor to obtain low dielectric constant. A kinetic analysis of the process was also performed to investigate the reaction mechanism. We focused on the effect of gas flow rate, i.e. the residence time of the precursors in the reactor, on growth rate and step coverage of SiO:F films. It revealed that there exists two species to form SiO:F films. One is the reactive species which contributes to increase the growth rate and the other one is the less reactive species which contributes to have uniform step coverage. The same approach was made on the PECVD process to produce low-k C:F films from C2F4, and we found ionic species is the main precursor to form C:F films.

Effect of Fluorine Addition to Plasma-Enhanced Chemical Vapor Deposition Silicon Oxide Film

1996 ◽  
Vol 443 ◽  
Author(s):  
S. W. Lim ◽  
M. Miyata ◽  
T. Naito ◽  
Y. Shimogaki ◽  
Y. Nakano ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Silicon Oxide ◽  
Chemical Vapor ◽  
Dielectric Constants ◽  
Low Dielectric Constant ◽  
Polarization Component ◽  
Low Dielectric ◽  
Step Coverage

AbstractOne solution to reduce the time constant of ultra large scale integrated circuit (ULSI) is the use of a low dielectric constant intermetal film like fluorinated silicon oxide (SiOF). We could obtain SiOF films with low dielectric constant as low as 2.6 and good step coverage by adding CF4 to SiH4 and N2O in plasma-enhanced chemical vapor deposition (PECVD) process. To investigate the dielectric constants due to each polarization and the reason for the decrease in the dielectric constant, we used capacitance-voltage (C-V) and ellipsometry measurements, and Kramers-Kronig transformation. The decrease in dielectric constant could not be completely explained by the reduction in ionic and electronic polarization. We could detect silanol groups, Si-OH in the films and their decrease with increasing CF4 flow rate. It is suggested that the main polarization component to decrease dielectric constant is such as orientational polarization. The step coverage of film was improved by adding CF4. It is suggested that the reduction in the sticking probability of films forming species due to the change in surface state improved the step coverage.

Integration Issues for Low Dielectric Constant Materials in each Generation of ULSI'S

1999 ◽  
Vol 565 ◽  
Author(s):  
Hideki Gomi ◽  
Koji Kishimoto ◽  
Tatsuya Usami ◽  
Ken-ichi Koyanagi ◽  
Takashi Yokoyama ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Silicon Oxide ◽  
Process Integration ◽  
Low Dielectric Constant ◽  
Next Generation ◽  
Hydrogen Silsesquioxane ◽  
Low Dielectric ◽  
Low Dielectric Constant Materials ◽  
Fluorinated Silicon Oxide ◽  
Low K

AbstractThe technologies utilizing Fluorinated Silicon Oxide (FSG, k=3.6) and Hydrogen Silsesquioxane (HSQ, k=3.0) have been established for 0.25-μm and 0.18-μm generation ULSIs. However, low-k materials for the next generation ULSIs, which have a dielectric constant of less than 3.0, have not become mature yet. In this paper, we review process integration issues in applying FSG and HSQ, and describe integration results and device performance using Fluorinated Amorphous Carbon (a-C:F, k=2.5) as one of the promising low-k materials for the next generation ULSIs.

Properties of New Low Dielectric Constant Spin-on Silicon Oxide based Polymers

1997 ◽  
Vol 476 ◽  
Author(s):  
Nigel P. Hacker ◽  
Gary Davis ◽  
Lisa Figge ◽  
Todd Krajewski ◽  
Scott Lefferts ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Silicon Oxide ◽  
Polymeric Materials ◽  
Low Dielectric Constant ◽  
Low Dielectric ◽  
Chip Size ◽  
Low Dielectric Constant Materials ◽  
Low K

Low dielectric constant materials (k < 3.0) have the advantage that higher performance IC devices may be manufactured with minimal increases in chip size. The reduced capacitance given by these materials permits shrinking spacing between metal lines to below 0.25 μm and the ability to decrease the number of levels of metal in a device. The technologies being considered for low k applications are CVD or spin-on of inorganic or organic polymeric materials. Traditional spin-on silicates or siloxanes have been used as planarizing dielectrics during the last 15 years and usually have k > 3.0.

Integration Issues for Low Dielectric Constant Materials in each Generation of ULSI's

1999 ◽  
Vol 564 ◽  
Author(s):  
Hideki Gomi ◽  
Koji Kishimoto ◽  
Tatsuya Usami ◽  
Ken-ichi Koyanagi ◽  
Takashi Yokoyama ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Silicon Oxide ◽  
Process Integration ◽  
Low Dielectric Constant ◽  
Next Generation ◽  
Hydrogen Silsesquioxane ◽  
Low Dielectric ◽  
Low Dielectric Constant Materials ◽  
Fluorinated Silicon Oxide ◽  
Low K

AbstractThe technologies utilizing Fluorinated Silicon Oxide (FSG, k=3.6) and Hydrogen Silsesquioxane (HSQ, k=3.0) have been established for 0.25-µm and 0.1 8-µm generation ULSIs. However, low-k materials for the next generation ULSIs, which have a dielectric constant of less than 3.0, have not become mature yet. In this paper, we review process integration issues in applying FSG and HSQ, and describe integration results and device performance using Fluorinated Amorphous Carbon (a-C:F, k=2.5) as one of the promising low-k materials for the next generation ULSIs.

The characterization and preparation of porous low dielectric films using various cyclodextrins as template materials

2003 ◽  
Vol 766 ◽  
Author(s):  
Jin-Heong Yim ◽  
Jung-Bae Kim ◽  
Hyun-Dam Jeong ◽  
Yi-Yeoul Lyu ◽  
Sang Kook Mah ◽  
...  
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Dielectric Constant ◽  
Pore Structure ◽  
Pore Diameter ◽  
Dielectric Films ◽  
Low Dielectric Constant ◽  
Cyclodextrin Derivatives ◽  
Low Dielectric ◽  
Low K

AbstractPorous low dielectric films containing nano pores (∼20Å) with low dielectric constant (<2.2), have been prepared by using various kinds of cyclodextrin derivatives as porogenic materials. The pore structure such as pore size and interconnectivity can be controlled by changing functional groups of the cyclodextrin derivatives. We found that mechanical properties of porous low-k thin film prepared with mCSSQ (modified cyclic silsesquioxane) precursor and cyclodextrin derivatives were correlated with the pore interconnection length. The longer the interconnection length of nanopores in the thin film, the worse the mechanical properties of the thin film (such as hardness and modulus) even though the pore diameter of the films were microporous (∼2nm).

Deposition of Fluorinated Amorphous Carbon Thin Films with Low Dielectric Constant and Thermal Stability

2000 ◽  
Vol 612 ◽  
Author(s):  
Sang-Soo Han ◽  
Byeong-Soo Bae
Keyword(s):  
Thin Films ◽  
Thermal Stability ◽  
Dielectric Constant ◽  
Amorphous Carbon ◽  
Inductively Coupled Plasma ◽  
Gas Flow ◽  
Stable Condition ◽  
Flow Rate Ratio ◽  
Low Dielectric Constant ◽  
Low Dielectric

AbstractFluorinated amorphous carbon (a-C:F) thin films were deposited by inductively coupled plasma enhanced chemical vapor deposition (ICP-CVD) with increasing CF4:CH4 gas flow rate ratio, and then annealed with increasing annealing temperature (100, 200, 300, and 400.). We have found the reduction mechanism of the dielectric constant and the thermally stable condition for the a-C:F films. On the basis of the results, the optimal condition to satisfy both the low dielectric constant and the thermal stability is followed as; the a-C:F films have to have the compatible F content to make a compromise between the two properties; the C-Fx bonding configuration has to exist as a form of C-F2 & C-F3 instead of C-F; The films should be somewhat cross-linked structure.

Infrared spectroscopy study of low-dielectric-constant fluorine-incorporated and carbon-incorporated silicon oxide films

2001 ◽  
Vol 90 (7) ◽  
pp. 3367-3370 ◽  
Author(s):  
Yoon-Hae Kim ◽  
Moo Sung Hwang ◽  
Hyeong Joon Kim ◽  
Jin Yong Kim ◽  
Young Lee
Keyword(s):  
Dielectric Constant ◽  
Infrared Spectroscopy ◽  
Silicon Oxide ◽  
Oxide Films ◽  
Low Dielectric Constant ◽  
Spectroscopy Study ◽  
Low Dielectric

Robust spin-on-glass poly(methyl)silsesquioxane-based low-k materials derived from a cyclic siloxane precursor

RSC Advances ◽  
2015 ◽  
Vol 5 (82) ◽  
pp. 66511-66517 ◽  
Author(s):  
Albert S. Lee ◽  
Sung Yeoun Oh ◽  
Seung-Sock Choi ◽  
He Seung Lee ◽  
Seung Sang Hwang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Dielectric Constant ◽  
Low Dielectric Constant ◽  
Cyclic Siloxane ◽  
Low Dielectric ◽  
Methyl Silsesquioxane ◽  
Low K

Low dielectric constant poly(methyl)silsesquioxane spin-on-glass resins incorporating a cyclic precursor exhibited exceptional mechanical properties to withstand CMP processes.

Chemical-Mechanical Planarization of Low-k Polymers for Advanced IC Structures

2002 ◽  
Vol 124 (4) ◽  
pp. 362-366 ◽  
Author(s):  
Christopher L. Borst ◽  
Dipto G. Thakurta ◽  
William N. Gill ◽  
Ronald J. Gutmann
Keyword(s):  
Dielectric Constant ◽  
Surface Chemistry ◽  
Chemical Mechanical Planarization ◽  
Low Dielectric Constant ◽  
Chemical Company ◽  
Low Dielectric ◽  
Scale Models ◽  
Physically Based ◽  
Thickness Measurements ◽  
Low K

Successful integration of copper and low dielectric constant (low-k) materials is dependent on robust chemical-mechanical planarization (CMP) during damascene patterning. This process includes the direct removal of copper and interaction of the copper slurry with the underlying dielectric. Experiments were designed and performed to examine the CMP of two low-k polymers from Dow Chemical Company, bis-benzocyclobutene (BCB*, k=2.65) and “silicon-application low-k material” (SiLK* resin, k=2.65) with both acidic slurries suitable for copper damascene patterning and a KH phthalate-based model slurry developed for SiLK. Blanket polymer films were polished in order to determine the interactions that occur when copper and liner materials are removed by the damascene CMP process. Removal rates were obtained from material thickness measurements, post-CMP surface topography from AFM scans, and post-CMP surface chemistry from XPS measurements. Physically based wafer-scale models are presented which are compatible with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document