The Effect of Oxygen on The Electrical Activation and Diffusion of Ion-Implanted Boron

1997 ◽  
Vol 469 ◽  
Author(s):  
K. Kyllesbech Larsen ◽  
P. A. Stoik ◽  
V. Privitera ◽  
J. G. M. van Berkum ◽  
W. B. de Boer ◽  
...  
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Secondary Ion Mass Spectrometry ◽  
Electrical Activation ◽  
Enhanced Diffusion ◽  
Boron Doped ◽  
Effect Of Oxygen ◽  
P Type ◽  
And Diffusion ◽  
Ion Implanted

ABSTRACTTransient enhanced diffusion (TED) and electrical activation (EA) of ion-implanted boron during rapid thermal annealing has been investigated using three types of boron doped p-type Si (100) substrates: (a) Cz 20 Ωcm, (b) 3 μm thick 20 Ωcm epitaxial Si layer (epi-layer) grown on a 20 Ωcm Cz substrate, and (c) 3 μm thick 20 Ωcm epi-layer grown on a 5 mΩcin Fz substrate. The level of oxygen is known to decrease from material type (a) to (c). The samples were implanted with 20 keV, 5×1013cm−2boron and subjected to rapid thermal annealing (RTA) at various temperatures and times. The EA and TED were studied using spreading resistance profiling (SRP) and secondary ion mass spectrometry (SIMS), respectively. Although the amount of TED is almost identical for the three substrates, the EA is found to be significantly higher in the epi-layers compared to Cz substrates. It is speculated that the trapping of vacancies by oxygen in the ion-damaged region leads to an increase in the interstitial supersaturation during annealing, which then results in enhanced boron clustering and reduced electrical activation in the peak of the implanted profile.

Ultra-Shallow Junctions by Ion Implantation and Rapid Thermal Annealing: Spike-Anneals, Ramp Rate Effects

1999 ◽  
Vol 568 ◽  
Author(s):  
Aditya Agarwal ◽  
Hans-J. Gossmann ◽  
Anthony T. Fiory
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Driving Forces ◽  
Recent Experimental Data ◽  
Enhanced Diffusion ◽  
Temperature Ramp ◽  
Rate Effects ◽  
Low Energies ◽  
Ultra Shallow Junctions ◽  
P Type

ABSTRACTOver the last couple of years rapid thermal annealing (RTA) equipment suppliers have been aggressively developing lamp-based furnaces capable of achieving ramp-up rates on the order of hundreds of degrees per second. One of the driving forces for adopting such a strategy was the experimental demonstration of 30nm p-type junctions by employing a ramp-up rate of ≈400°C/s. It was subsequently proposed that the ultra-fast temperature ramp-up was suppressing transient enhanced diffusion (TED) of boron which results from the interaction of the implantation damage with the dopant. The capability to achieve very high temperature ramp-rates was thus embraced as an essential requirement of the next generation of RTA equipment.In this paper, recent experimental data examining the effect of the ramp-up rate during spike-and soak-anneals on enhanced diffusion and shallow junction formation is reviewed. The advantage of increasing the ramp-up rate is found to be largest for the shallowest, 0.5-keV, B implants. At such ultra-low energies (ULE) the advantage arises from a reduction of the total thermal budget. Simulations reveal that a point of diminishing return is quickly reached when increasing the ramp-up rate since the ramp-down rate is in practice limited. At energies where TED dominates, a high ramp-up rate is only effective in minimizing diffusion if the implanted dose is sufficiently small so that the TED can be run out during the ramp-up portion of the anneal; for larger doses, a high ramp-up rate only serves to postpone the TED to the ramp-down duration of the anneal. However, even when TED is minimized at higher implant energies via high ramp-up rates, the advantage is unobservable due to the rather large as-implanted depth. It appears then that while spike anneals allow the activation of ULE-implanted dopants to be maximized while minimizing their diffusion the limitation imposed by the ramp-down rate compromises the advantage of very aggressive ramp-up rates.

scholarly journals Self- and Dopant Diffusion in Extrinsic Boron Doped Isotopically Controlled Silicon Multilayer Structures

2002 ◽  
Vol 719 ◽  
Author(s):  
Ian D. Sharp ◽  
Hartmut A. Bracht ◽  
Hughes H. Silvestri ◽  
Samuel P. Nicols ◽  
Jeffrey W. Beeman ◽  
...  
Keyword(s):  
Multilayer Structure ◽  
Secondary Ion Mass Spectrometry ◽  
Diffusion Processes ◽  
Quantitative Description ◽  
Multilayer Structures ◽  
Dopant Diffusion ◽  
Enhanced Diffusion ◽  
Self Diffusion ◽  
Boron Doped ◽  
P Type

AbstractIsotopically controlled silicon multilayer structures were used to measure the enhancement of self- and dopant diffusion in extrinsic boron doped silicon. 30Si was used as a tracer through a multilayer structure of alternating natural Si and enriched 28Si layers. Low energy, high resolution secondary ion mass spectrometry (SIMS) allowed for simultaneous measurement of self- and dopant diffusion profiles of samples annealed at temperatures between 850°C and 1100°C. A specially designed ion-implanted amorphous Si surface layer was used as a dopant source to suppress excess defects in the multilayer structure, thereby eliminating transient enhanced diffusion (TED) behavior. Self- and dopant diffusion coefficients, diffusion mechanisms, and native defect charge states were determined from computer-aided modeling, based on differential equations describing the diffusion processes. We present a quantitative description of B diffusion enhanced self-diffusion in silicon and conclude that the diffusion of both B and Si is mainly mediated by neutral and singly positively charged self-interstitials under p-type doping. No significant contribution of vacancies to either B or Si diffusion is observed.

Oxygen Gettering and Thermal Donor Formation at Post-Implantation Annealing of Hydrogen Implanted Czochralski Silicon

1997 ◽  
Vol 469 ◽  
Author(s):  
A. G. Ulyashin ◽  
Yu. A. Bumay ◽  
W. R. Fahrner ◽  
A. I. Ivanovo ◽  
R. Job ◽  
...  
Keyword(s):  
Secondary Ion Mass Spectrometry ◽  
Hydrogen Ions ◽  
Enhanced Diffusion ◽  
Thermal Donor ◽  
Float Zone ◽  
Donor Formation ◽  
Effect Of Oxygen ◽  
P Type ◽  
Secondary Ion ◽  
Post Implantation

ABSTRACTThe effect of oxygen gettering by buried defect layers at post-implantation annealing of hydrogen implanted Czochralski (Cz) grown silicon has been investigated. Hydrogen ions were implanted with an energy of 180 keV and doses of 2.7.1016cm−2 into p-type Cz and for comparison into p-type float zone (Fz) Si. The samples were annealed at temperatures between 400 °C and 1200 °C in a forming gas ambient and examined by secondary ion mass spectrometry (SIMS) in order to measure the hydrogen and oxygen concentration profiles. Spreading resistance probe (SRP) measurements were used to obtain depth resolved profiles of the resistivity. The observed changes of the resistivity after post-implantation annealing of hydrogen implanted Cz and Fz Si can be explained by hydrogen enhanced thermal donor formation processes (oxygen or hydrogen related) and charges at the SiOx precipitates. The effective oxygen gettering in hydrogen implanted Cz silicon is attributed to hydrogen enhanced diffusion of oxygen to buried defect layers.

The Ion Implanted Arsenic Tail in Silicon

1989 ◽  
Vol 147 ◽  
Author(s):  
S. E. Beck ◽  
R. J. Jaccodine ◽  
C. Clark
Keyword(s):  
Silicon Dioxide ◽  
Thermal Annealing ◽  
Anodic Oxidation ◽  
Rapid Thermal Annealing ◽  
Deep Level Transient Spectroscopy ◽  
Deep Level ◽  
Electrical Activation ◽  
Spreading Resistance ◽  
Transient Spectroscopy ◽  
And Diffusion

AbstractRapid thermal annealed tail regions of shallow junction arsenic implants into silicon have been investigated. Tail profiles have been roduced by an anodic oxidation and stripping technique after implantation to fluences of 1014 to 1016 cm−2 and by implanting through a layer of silicon dioxide. Electrical activation and diffusion have been achieved by rapid thermal annealing in the temperature range of 800 to 1100 °C. Electrically active defects remain after annealing. Spreading resistance and deep level transient spectroscopy results are presented. The diffusion of the arsenic tail is discussed and compared with currently accepted models.

Activation Mechanisms in Ion-Implanted GaAs

1988 ◽  
Vol 126 ◽  
Author(s):  
N. Morris ◽  
B. J. Sealy
Keyword(s):  
Electrical Properties ◽  
Electrical Activity ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Annealing Time ◽  
Electrical Activation ◽  
Annealing Stage ◽  
Activation Mechanisms ◽  
Ion Implanted

ABSTRACTRapid thermal annealing has been used to study the electrical activation mechanisms for magnesium and selenium implants in GaAs. By analysing the changes in electrical activity as a function of annealing time and temperature, a model has been developed which accurately predicts the electrical properties following the post-implant annealing stage. The model has been used to study the activation of other ions, particularly zinc, beryllium, tin and sulphur, the results of which will be compared with those of magnesium and selenium. The results suggest that the mechanism for electrical activation is dominated by the diffusion of gallium, arsenic or vacancies. The paper will present the model and discuss the activation mechanisms of the ions.

scholarly journals Transient Enhanced Diffusion and Gettering of Dopants in Ion Implanted Silicon

1984 ◽  
Vol 36 ◽  
Author(s):  
S. J. Pennycook ◽  
J. Narayan ◽  
R. J. Culbertson
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Solid Phase ◽  
Subsequent Annealing ◽  
Dislocation Loops ◽  
Enhanced Diffusion ◽  
Transient Enhanced Diffusion ◽  
Dopant Profile ◽  
Dopant Atoms ◽  
Ion Implanted

ABSTRACTWe have studied in detail the transient enhanced diffusion observed during furnace or rapid-thermal-annealing of ion-implanted Si. We show that the effect originates in the trapping of Si atoms by dopant atoms during implantation, which are retained during solid-phase-epitaxial (SPE) growth but released by subsequent annealing to cause a transient dopant precipitation or profile broadening. The interstitials condense to form a band of dislocation loops located at the peak of the dopant profile, which may be distinct from the band formed at the original amorphous/crystalline interface. The band can develop into a network and effectively getter the dopant. We discuss the conditions under which the various effects may or may not be observed, and discuss preliminary observations on As+ implanted Si.

Rapid Thermal Anneal and Furnace Anneal of Silicon and Beryimlum Implanted Gallium Arsenide

1985 ◽  
Vol 45 ◽  
Author(s):  
A.T. Yuen ◽  
S.I. Long ◽  
J.L. Merz
Keyword(s):  
Gallium Arsenide ◽  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Electrical Activation ◽  
Donor Concentration ◽  
Rapid Thermal Anneal ◽  
Furnace Annealing ◽  
Hall Measurements ◽  
P Type

ABSTRACTA comparison has been made between rapid thermal annealing (RTA) and furnace annealing (FA) of implanted GaAs. Hall measurements showed consistently higher electrical activation of n-type (Si-5E12 cm −2) implants with FA and higher electrical activation of p-type (Be-1E14 cm −2) implants with RTA. Photoluminescence (PL) revealed that for RTA temperatures above 950°C some of the Si was going onto As, acceptor sites, thus reducing the net donor concentration. PL for RTA below 950°C showed signs of incomplete recrystallization. By a technique of “dual implantation” of As and Si into GaAs we were able to force the Si onto Ga-sites resulting in a higher donor concentration after RTA.

Sign in / Sign up

Export Citation Format

Share Document