Mechanism of Wetting During Solder Joint Formation

2009 ◽  
pp. 20-20-9
Author(s):  
Howard H. Manko
Keyword(s):  
Solder Joint ◽  
Joint Formation

The Effects of Electromigration to the Solder Joint Formation: A Comparison Between 99.3Sn-0.7Cu and 96.5Sn-3.0Ag-0.5Cu Lead Free Solder

2012 ◽  
Vol 622-623 ◽  
pp. 195-199 ◽  
Author(s):  
M.A.A. Mohd Salleh ◽  
A.R. Nik Nurhidayatul Suhada ◽  
Flora Somidin ◽  
Rafezi Ahmad Khairel ◽  
C.S. Lee ◽  
...  
Keyword(s):  
Solder Joint ◽  
Room Temperature ◽  
Solder Joints ◽  
Research Work ◽  
Cathode Region ◽  
Lead Free ◽  
Lead Free Solder ◽  
Joint Formation ◽  
Current Stress ◽  
Free Solder

Electromigration effects on the solder joint formation of 99.3Sn-0.7Cu and 96.5Sn-3.0Ag-0.5Cu lead-free solder with Cu electroplated Ni layer wire were investigated. The electromigration effects on the solder joints were studied after current density stressing at 1 x 103 A/cm2 in room temperature for 0 h, 120 h, and 240 h. The research work found that intermetallic compound (IMC) formation on the joint is increases for both solders with longer period of current stress applied. Higher IMC thickness growth in 99.3Sn-0.7Cu solder joint compared to 99.3Sn-0.7Cu is detected and both anode regions of the solder joints show higher IMC thickness growth compared to cathode region. Experimental results show 99.3Sn-0.7Cu solder joint is more prone to failure under current stress compared to 96.5Sn-3.0Ag-0.5Cu solder joint with thicker IMC which translates to higher brittleness.

Automatic computer-aided system of simulating solder joint formation

1999 ◽  
Author(s):  
Xiujuan Zhao ◽  
Chunqing Wang ◽  
Guanqun Zheng ◽  
Gouzhong Wang ◽  
Shiqin Yang
Keyword(s):  
Solder Joint ◽  
Joint Formation ◽  
Automatic Computer ◽  
Computer Aided

Solder Joint Formation in Surface Mount Technology—Part II: Design

1990 ◽  
Vol 112 (3) ◽  
pp. 219-222 ◽  
Author(s):  
S. M. Heinrich ◽  
N. J. Nigro ◽  
A. F. Elkouh ◽  
P. S. Lee
Keyword(s):  
Surface Tension ◽  
Solder Joint ◽  
Solder Joints ◽  
Cross Sectional Area ◽  
Surface Mount Technology ◽  
Sectional Area ◽  
Cross Sectional ◽  
Joint Formation ◽  
Surface Mount ◽  
Surface Tension Model

In this paper dimensionless design curves relating fillet height and length to joint cross-sectional area are presented for surface-mount solder joints. Based on an analytical surface tension model, the advantage of these dimensionless curves is that they may be used for arbitrary values of solder density and surface tension. The range of applicability of previously developed approximate formulae for predicting joint dimensions is also investigated. A simple example problem is included to illustrate the use of both the design curves and the approximate formulae.

Solder Joint Formation Simulation and Component Tombstoning Prediction During Reflow

1998 ◽  
Vol 120 (2) ◽  
pp. 141-144 ◽  
Author(s):  
X. Wu ◽  
X. Dou ◽  
C.-P. Yeh ◽  
K. Waytt
Keyword(s):  
Solder Joint ◽  
Model Simulation ◽  
Software Tool ◽  
Solder Paste ◽  
Reflow Process ◽  
Surface Evolver ◽  
Joint Formation ◽  
Geometry Design ◽  
Reliability Performance ◽  
Public Domain Software

The failure of electrical devices associated with solder joints has become one of the most critical reliability issues for surface-mounted devices. Solder joint reliability performance has been found to be highly dependent on the solder joint configuration, which, in turn, is governed by bond pad size, alloy material, and leadframe structure, as well as solder reflow characteristics. To investigate tombstone effects causing solder joint failure during leadless component reflow process, this work has focused on (1) developing a numerical model for the simulations of the solder joint formation during the reflow process, and (2) determining possibility that a tombstone effect for the leadless component may occur by analyzing the force and torque in the problem. Using this methodology, the tombstone effect associated with different pad geometry configurations and solder paste amount has been analyzed through the application of the public domain software tool Surface Evolver. Simulations show that the tombstoning is very sensitive to pad/component geometry design, solder surface tension, solder paste volume, wetting area, and wetting angle. This model simulation can be used to determine optimal solder paste volume, pad geometry configurations, and solder material for avoiding tombstone effects.

Effect of Chip and Pad Geometry on Solder Joint Formation in SMT

1993 ◽  
Vol 115 (4) ◽  
pp. 433-439 ◽  
Author(s):  
S. M. Heinrich ◽  
P. E. Liedtke ◽  
N. J. Nigro ◽  
A. F. Elkouh ◽  
P. S. Lee
Keyword(s):  
Solder Joint ◽  
Printed Circuit Board ◽  
Integrated Approach ◽  
Contact Angles ◽  
Circuit Board ◽  
Zero Gravity ◽  
Cross Sectional ◽  
Board Density ◽  
Joint Formation ◽  
Maximum Utility

An analytical model of solder joint formation during a surface mount reflow process is developed for two-dimensional fillets whose flow may be restricted due to “finite” metallizations on a leadless component and the printed circuit board. Although these height and length constraints on the fillet geometry may result in obtuse contact angles, the solution is obtained in the form of an explicit integral, similar to that previously derived by the authors for the case of acute contact angles. This solution may also be recast into the form of elliptic integrals of the first and second kinds, thereby permitting one to evaluate the fillet geometry using mathematical tables or special function software, if desired, rather than resorting to a computer-based numerical quadrature. In addition an approximate zero-gravity solution is given by means of simple closed-form expressions relating the height, length, contact angles, and cross-sectional area of the fillet. Numerical results generated by implementing the “exact” integral solution for the joint profile are given in the form of dimensionless plots, relating fillet geometry to the solder properties (surface tension and density), amount of solder, chip height, and pad length. Also presented in dimensionless form are the approximate results from the zero-gravity model, which are independent of solder properties, yet are of sufficient accuracy for “small” joints. Because of their dimensionless nature, the results of the present paper may be of maximum utility to process engineers aiming to achieve desired joint geometries (e.g., to maximize fatigue life or to eliminate bridging problems), or to board designers responsible for selecting efficient footprint patterns to maximize board density. Models of solder joint formation, such as the one presented here, may be of most value when used in conjunction with stress analysis packages (e.g., finite element programs) and appropriate fatigue models. In this way an integrated approach to the design of solder joints and circuit boards may be taken, resulting in improved product reliability and performance.

Solder Joint Formation in Surface Mount Technology—Part I: Analysis

1990 ◽  
Vol 112 (3) ◽  
pp. 210-218 ◽  
Author(s):  
S. M. Heinrich ◽  
A. F. Elkouh ◽  
N. J. Nigro ◽  
Ping S. Lee
Keyword(s):  
Solder Joint ◽  
Laboratory Data ◽  
Integral Form ◽  
Contact Angles ◽  
Reflow Process ◽  
Cross Sectional ◽  
Joint Formation ◽  
Surface Mount ◽  
Theoretical Predictions ◽  
Joint Shape

An analytical model of solder joint formation during a surface mount reflow process is developed in the present paper, and the solution is obtained in an explicit integral form. For two limiting cases—infinitesimal and infinite solder areas—the solution is expressed in closed form. Numerical results illustrate the influence of the process parameters (surface tension, density, and cross-sectional area of the molten solder, and the contact angles between the solder andpretinning) on joint shape and overall fillet dimensions. Comparisons between theoretical predictions and laboratory data show excellent agreement.

Sign in / Sign up

Export Citation Format

Share Document