Analysis of semitransparent layered materials by modulated photothermal radiometry: application to the bonding and thickness control of enamel coatings

1986 ◽  
Vol 64 (9) ◽  
pp. 1297-1302 ◽  
Author(s):  
Michel Egee ◽  
Robert Dartois ◽  
Jean Marx ◽  
Christian Bissieux
Keyword(s):  
Theoretical Model ◽  
Thermal Resistance ◽  
Coating Thickness ◽  
Thermophysical Properties ◽  
Layered Materials ◽  
Photothermal Radiometry ◽  
Experimental Results ◽  
Adhesion Properties ◽  
Thickness Control

To use modulated photothermal radiometry to control the thermophysical properties of enamel coatings, we first analytically resolve a theoretical model with two finite semitransparent layers and thermal-resistance interface; then we experimentally study several samples with various adhesion properties. The comparison of the experimental results with the calculations allows one, under the present conditions, to point out the possibilities and limits of the method, mainly for the control of coating thickness and delaminations.

Photothermal Radiometry of Thermal Spray Coatings: Thermophysical Properties and Disbonding Effects Characterization

2000 ◽  
Author(s):  
A. Mandelis ◽  
J.A. Garcia ◽  
B. Farahbarhsh
Keyword(s):  
Thermophysical Properties ◽  
Photothermal Radiometry ◽  
Experimental Results ◽  
In Situ Monitoring ◽  
Spray Coatings ◽  
Interfacial Defects ◽  
Steel Substrates ◽  
Sprayed Coatings ◽  
Thermal Sprayed Coatings

Abstract Laser infrared photothermal radiometry (PTR) can be used to determine the thermophysical properties (thermal diffusivity and conductivity) and interfacial defects (i.e. disbonding) of various thermal sprayed coatings on carbon steel substrates. PTR experimental results are compared with a one-dimensional photothermal model that can take into account roughness affects and interfacial defects by considering a roughness equivalent-layer and an equivalent-thermal resistance, respectively. The foregoing thermophysical parameters of the thermal sprayed coatings are obtained when a multi-parameter optimization algorithm is used to fit the PTR experimental results. The potential of the PTR technique for in-situ monitoring of the coating process and the characterization of the thermal sprayed coatings will be discussed in this paper.

Actuation and dynamic mechanical characteristics of a core free flat dielectric electro-active polymer soft actuator

2020 ◽  
Vol 14 (4) ◽  
pp. 7396-7404
Author(s):  
Abdul Malek Abdul Wahab ◽  
Emiliano Rustighi ◽  
Zainudin A.
Keyword(s):  
Theoretical Model ◽  
Resonance Frequency ◽  
Dynamic Testing ◽  
Experimental Results ◽  
Percentage Error ◽  
Initial Tension ◽  
Average Percentage ◽  
Soft Actuator ◽  
Average Percentage Error ◽  
Mechanical Dynamics

Various complex shapes of dielectric electro-active polymer (DEAP) actuator have been promoted for several types of applications. In this study, the actuation and mechanical dynamics characteristics of a new core free flat DEAP soft actuator were investigated. This actuator was developed by Danfoss PolyPower. DC voltage of up to 2000 V was supplied for identifying the actuation characteristics of the actuator and compare with the existing formula. The operational frequency of the actuator was determined by dynamic testing. Then, the soft actuator has been modelled as a uniform bar rigidly fixed at one end and attached to mass at another end. Results from the theoretical model were compared with the experimental results. It was found that the deformation of the current actuator was quadratic proportional to the voltage supplied. It was found that experimental results and theory were not in good agreement for low and high voltage with average percentage error are 104% and 20.7%, respectively. The resonance frequency of the actuator was near 14 Hz. Mass of load added, inhomogeneity and initial tension significantly affected the resonance frequency of the soft actuator. The experimental results were consistent with the theoretical model at zero load. However, due to inhomogeneity, the frequency response function’s plot underlines a poor prediction where the theoretical calculation was far from experimental results as values of load increasing with the average percentage error 15.7%. Hence, it shows the proposed analytical procedure not suitable to provide accurate natural frequency for the DEAP soft actuator.

Experimental Study on the Specific Heat Capacity Measurement of Water-Based Al2O3-Cu Hybrid Nanofluid by using Differential Thermal Analysis Method

2019 ◽  
Vol 15 ◽  
Author(s):  
Andaç Batur Çolak ◽  
Oğuzhan Yıldız ◽  
Mustafa Bayrak ◽  
Ali Celen ◽  
Ahmet Selim Dalkılıç ◽  
...  
Keyword(s):  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Thermophysical Properties ◽  
Volume Concentration ◽  
Pure Water ◽  
Heat Capacity Measurement ◽  
Experimental Results ◽  
Hybrid Nanofluid ◽  
Capacity Measurement

Background: Researchers working in the field of nanofluid have done many studies on the thermophysical properties of nanofluids. Among these studies, the number of studies on specific heat are rather limited. In the study of the heat transfer performance of nanofluids, it is necessary to increase the number of specific heat studies, whose subject is one of the important thermophysical properties. Objective: The authors aimed to measure the specific heat values of Al2O3/water, Cu/water nanofluids and Al2O3-Cu/water hybrid nanofluids using the DTA method, and compare the results with those frequently used in the literature. In addition, this study focuses on the effect of temperature and volume concentration on specific heat. Method: The two-step method was used in the preparation of nanofluids. The pure water selected as the base fluid was mixed with the Al2O3 and Cu nanoparticles and Arabic Gum as the surfactant, firstly mixed in the magnetic stirrer for half an hour. It was then homogenized for 6 hours in the ultrasonic homogenizer. Results: After the experiments, the specific heat of nanofluids and hybrid nanofluid were compared and the temperature and volume concentration of specific heat were investigated. Then, the experimental results obtained for all three fluids were compared with the two frequently used correlations in the literature. Conclusion: Specific heat capacity increased with increasing temperature, and decreased with increasing volume concentration for three tested nanofluids. Cu/water has the lowest specific heat capacity among all tested fluids. Experimental specific heat capacity measurement results are compared by using the models developed by Pak and Cho and Xuan and Roetzel. According to experimental results, these correlations can predict experimental results within the range of ±1%.

scholarly journals Early-Age Tensile Bond Characteristics of Epoxy Coatings for Underwater Applications

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 757 ◽  
Author(s):  
Kim ◽  
Hong ◽  
Han ◽  
Kim
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Epoxy Resin ◽  
Coating Thickness ◽  
Experimental Results ◽  
Early Age ◽  
Curing Time ◽  
Bond Performance ◽  
Coating Type ◽  
Bond Characteristics

In this study, coating equipment for the effective underwater repair of submerged structures was developed. The tensile bond characteristics of selected epoxy resin coatings were investigated by coating the surface of a specimen using each of the four types of equipment. Using the experimental results, the tensile bond strength and the coating thickness were analyzed according to the type of equipment, coating, and curing time. The results show that the type of coating equipment used had the greatest effect on the measured bond strength and coating thickness of the selected coatings. However, the effect of coating type and curing time on the bond strength and the thickness was observed to be insignificant. Compared with the developed equipment, the surface treatment of the coating was observed to be more effective when using the pre-existing equipment, and thus the bond performance of the coating was improved compared to using the pre-existing equipment. Based on the experimental results, improvements and needs involving the equipment for further research were discussed.

Preparation and Properties of the Polystyrene/Alumina Nanocomposites

2012 ◽  
Vol 557-559 ◽  
pp. 519-522
Author(s):  
Xu Man Wang ◽  
Cai Ning Zhang
Keyword(s):  
Molecular Weight ◽  
Thermal Resistance ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
In Situ Polymerization ◽  
Average Molecular Weight ◽  
Experimental Results ◽  
Solvent Resistance ◽  
Silane Coupling

Silane coupling agent KH-570 was applied to modify the surface capability of the alumina (Al2O3). The modified Al2O3were dispersed in styrene. The in-situ polymerization was used to prepare the polystyrene/alumina (PS/Al2O3) composites, in which azodiisobutyronitrile (AIBN) was used as initiator. FTIR, DSC and TG were applied to characterize the prepared composites. The solvent resistance, thermal resistance of the composites and the average molecular weight of PS in PS/Al2O3nanocomposites were studied. The experimental results demonstrated that the solvent resistance of PS/Al2O3nanocomposites was improved by the adding of Al2O3nanoparticles. The thermal resistance of the composites increased with the increasing of the Al2O3content. Meanwhile, the molecular weight of PS in the composites increased with the increasing of the Al2O3content.

Research on the thickness control method of workbench oil film based on theoretical model

2018 ◽  
Author(s):  
Tang Pei ◽  
Lin Lin ◽  
Ge Liu ◽  
Liping Yu ◽  
Zhen Xu ◽  
...  
Keyword(s):  
Theoretical Model ◽  
Control Method ◽  
Thickness Control ◽  
Oil Film

scholarly journals Investigation of thermal conductivity of single-wall carbon nanotubes

2011 ◽  
Vol 15 (2) ◽  
pp. 565-570 ◽  
Author(s):  
Mahmoud Jafari ◽  
Majid Vaezzadeh ◽  
Momhamad Mansouri ◽  
Abazar Hajnorouzi
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Theoretical Model ◽  
Potential Energy ◽  
Experimental Results ◽  
Single Wall Carbon Nanotubes ◽  
Lattice Vibrations ◽  
Single Wall Carbon ◽  
Thermal Potential ◽  
Conductivity Behavior

In this paper, the thermal conductivity of Single-wall carbon nanotubes (SWCNTs) is determined by lattice vibrations (phonons) and free elections. The thermal conductivity of SWCNTs is modeled up to 8-300 K and the observed deviations in K-T figures of SWCNTs are explained in terms of phonon vibrations models. An suitable theoretical model is shown for thermal conductivity behavior with respect to temperature and is generalized for experimental results. This model enables us to calculate thermal conductivity SWNTs and Thermal Potential Energy (TPE).

Theoretical Model for Interfacial Nonlinear Bond Softening Behavior between Embedded Steel and HSHPC

2007 ◽  
Vol 348-349 ◽  
pp. 845-848
Author(s):  
Shan Suo Zheng ◽  
Lei Li ◽  
Guo Zhuan Deng ◽  
Shun Li Che ◽  
Wei Zhao
Keyword(s):  
Theoretical Model ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Nonlinear Process ◽  
Experimental Results ◽  
Interfacial Bond ◽  
Bond Slip ◽  
Softening Behavior ◽  
Bond Softening

The latest experimental study on steel reinforced high strength and high performance concrete (SRHSHPC) specimens shows that there exists interfacial bond softening phenomenon between embedded steel and high strength and high performance concrete (HSHPC), and it makes the shear transfer capacity between shaped steel and HSHPC be progressively reduced. To predict failure load in design, a theoretical model for interfacial bond softening behavior is required. As interfacial bond softening behavior is a nonlinear process involving material properties, it can be analyzed once the relation of interfacial bond stress (τ ) and slippage ( s ) is known. In this paper, the mechanism of interfacial bond-slip is studied, thus a simplified τ − s relation including ascending and descending parts is proposed and employed to analyze the interfacial nonlinear bond-slip process. Based on the interfacial equilibrium between steel and HSHPC as well as the τ − s relation, the basic governing equations in both softened region and elastic region are established and solved for steel strain or stress. At last, the application of the model is verified through comparison with experimental results. The calculating results of the model are found to be in good agreement with experimental results, showing that the model can describe the bond-slip process in real material systems.

Sign in / Sign up

Export Citation Format

Share Document