Influence of Nucleate Boiling on the Design of Automotive Cooling Systems

2002 ◽  
Author(s):  
Steve Strepek ◽  
Richard H. S. Winterton ◽  
Marc Wiseman ◽  
Chris Nelson
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Hot Spots ◽  
Nucleate Boiling ◽  
Film Boiling ◽  
Cooling Systems ◽  
Higher Power ◽  
Correct Calculation ◽  
Cae Analysis ◽  
The Heat Transfer Coefficient

With higher power ratings in automotive cooling systems the correct calculation of the heat transfer coefficient when nucleate boiling is occurring has become important. In accounting for the enhanced cooling that nucleate boiling provides, analysts can achieve two goals: more accurate metal temperature prediction at local hot spots; and an assessment of the probability that catastrophic film boiling will occur. Two correlations examined: the classic Chen correlation and the more recent Liu and Winterton correlation. The method of extending the correlations to mixtures is explained. Predictions are presented for the 50:50 mixture of water and ethylene glycol, and compared with literature data. The method of incorporating these correlations into engine CAE analysis is explained and demonstrated. The paper also considers the effect of nucleate boiling on vapor production, leading to vapor blanketing and the critical heat flux. A method of estimating critical heat flux for the mixture is described.

scholarly journals ELETRIC FIELD ENHANCEMENT AND DETERIORATION OF BOILING HEAT TRANSFER AND CRITICAL HEAT FLUX IN DIELECTRIC FLUIDS

2001 ◽  
Vol 1 (1) ◽  
pp. 32
Author(s):  
P. M. Carrica ◽  
V. Masson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Electric Fields ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Film Boiling ◽  
Two Phase ◽  
Boiling Regime ◽  
Dielectric Fluids

We present the results of an experimental study of the effects of externally imposed electric fields on boiling heat transfer and critical heat flux (CHF) in dielectric fluids. The study comprises the analysis of geometries that, under the effects of electric fields, cause the bubbles either to be pushed toward the heater or away from it. A local phase detection probe was used to measure the void fraction and the interfacial impact rate near the heater. It was found that the critical heat flux can be either augmented or reduced with the application of an electric field, depending on the direction of . In addition, the heat transfer can be slightly enhanced or degraded depending on the heat flux. The study of the two-phase flow in nucleate boiling, only for the case of favorable dielectrophoretic forces, reveals that the application of an electric field reduces the bubble detection time and increases the detachment frequency. It also shows that the two-phase flow characteristics of the second film boiling regime resemble more a nucleate boiling regime than a film boiling regime.

scholarly journals ELETRIC FIELD ENHANCEMENT AND DETERIORATION OF BOILING HEAT TRANSFER AND CRITICAL HEAT FLUX IN DIELECTRIC FLUIDS

2002 ◽  
Vol 1 (1) ◽  
Author(s):  
P. M. Carrica ◽  
V. Masson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Electric Fields ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Film Boiling ◽  
Two Phase ◽  
Boiling Regime ◽  
Dielectric Fluids

We present the results of an experimental study of the effects of externally imposed electric fields on boiling heat transfer and critical heat flux (CHF) in dielectric fluids. The study comprises the analysis of geometries that, under the effects of electric fields, cause the bubbles either to be pushed toward the heater or away from it. A local phase detection probe was used to measure the void fraction and the interfacial impact rate near the heater. It was found that the critical heat flux can be either augmented or reduced with the application of an electric field, depending on the direction of . In addition, the heat transfer can be slightly enhanced or degraded depending on the heat flux. The study of the two-phase flow in nucleate boiling, only for the case of favorable dielectrophoretic forces, reveals that the application of an electric field reduces the bubble detection time and increases the detachment frequency. It also shows that the two-phase flow characteristics of the second film boiling regime resemble more a nucleate boiling regime than a film boiling regime.

Pool Boiling of FC-72 and HFE-7100

1999 ◽  
Vol 123 (2) ◽  
pp. 399-400 ◽  
Author(s):  
Z. W. Liu ◽  
W. W. Lin ◽  
D. J. Lee ◽  
X. F. Peng
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Atmospheric Pressure ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Film Boiling ◽  
Boiling Mode

This work reported the boiling characteristics of FC-72 and HFE-7100 at atmospheric pressure and at a liquid subcooling of 0–20 K. The FC-72 exhibits a more efficient nucleate boiling mode and a higher critical heat flux (CHF) than the HFE-7100. For film boiling mode, HFE-7100 becomes more efficient.

Boiling Heat Transfer and Critical Heat Flux Enhancement of Upward- and Downward-Facing Heater in Nanofluids

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Muhamad Zuhairi Sulaiman ◽  
Masahiro Takamura ◽  
Kazuki Nakahashi ◽  
Tomio Okawa
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Flux Enhancement ◽  
Optimum Configuration ◽  
Wall Superheat ◽  
Nucleate Boiling Heat Transfer

Boiling heat transfer (BHT) and critical heat flux (CHF) performance were experimentally studied for saturated pool boiling of water-based nanofluids. In present experimental works, copper heaters of 20 mm diameter with titanium-oxide (TiO2) nanocoated surface were produced in pool boiling of nanofluid. Experiments were performed in both upward and downward facing nanofluid coated heater surface. TiO2 nanoparticle was used with concentration ranging from 0.004 until 0.4 kg/m3 and boiling time of tb = 1, 3, 10, 20, 40, and 60 mins. Distilled water was used to observed BHT and CHF performance of different nanofluids boiling time and concentration configurations. Nucleate boiling heat transfer observed to deteriorate in upward facing heater, however; in contrast effect of enhancement for downward. Maximum enhancements of CHF for upward- and downward-facing heater are 2.1 and 1.9 times, respectively. Reduction of mean contact angle demonstrate enhancement on the critical heat flux for both upward-facing and downward-facing heater configuration. However, nucleate boiling heat transfer shows inconsistency in similar concentration with sequence of boiling time. For both downward- and upward-facing nanocoated heater's BHT and CHF, the optimum configuration denotes by C = 400 kg/m3 with tb = 1 min which shows the best increment of boiling curve trend with lowest wall superheat ΔT = 25 K and critical heat flux enhancement of 2.02 times.

Study on Subcooled-Forced Flow Boiling Heat Transfer and Critical Heat Flux of Solid-Water Two-Phase Mixture

1999 ◽  
Author(s):  
Yasuo Koizumi ◽  
Hiroyasu Ohtake ◽  
Manabu Mochizuki
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Liquid Layer ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Forced Flow ◽  
Superheated Liquid ◽  
Flow Boiling Heat Transfer

Abstract The effect of solid particle introduction on subcooled-forced flow boiling heat transfer and a critical heat flux was examined experimentally. In the experiment, glass beads of 0.6 mm diameter were mixed in subcooled water. Experiments were conducted in a range of the subcooling of 40 K, a velocity of 0.17–6.7 m/s, a volumetric particle ratio of 0–17%. When particles were introduced, the growth of a superheated liquid layer near a heat trasnsfer surface seemed to be suppressed and the onset of nucleate boiling was delayed. The particles promoted the condensation of bubbles on the heat transfer surface, which shifted the initiation of a net vapor generation to a high heat flux region. Boiling heat trasnfer was augmented by the particle introduction. The suppression of the growth of the superheated liquid layer and the promotion of bubble condensation and dissipation by the particles seemed to contribute that heat transfer augmentation. The wall superheat at the critical heat flux was elevated by the particle introduction and the critical heat flux itself was also enhanced. However, the degree of the critical heat flux improvement was not drastic.

Sign in / Sign up

Export Citation Format

Share Document