POST-NUCLEATE BOILING AND CRITICAL HEAT FLUX FROM HORIZONTAL HEATED SURFACES

1978 ◽  
Author(s):  
P. K. Mohan Rao ◽  
D. G. Andrews
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Nucleate Boiling

Boiling Heat Transfer and Critical Heat Flux Enhancement of Upward- and Downward-Facing Heater in Nanofluids

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Muhamad Zuhairi Sulaiman ◽  
Masahiro Takamura ◽  
Kazuki Nakahashi ◽  
Tomio Okawa
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Flux Enhancement ◽  
Optimum Configuration ◽  
Wall Superheat ◽  
Nucleate Boiling Heat Transfer

Boiling heat transfer (BHT) and critical heat flux (CHF) performance were experimentally studied for saturated pool boiling of water-based nanofluids. In present experimental works, copper heaters of 20 mm diameter with titanium-oxide (TiO2) nanocoated surface were produced in pool boiling of nanofluid. Experiments were performed in both upward and downward facing nanofluid coated heater surface. TiO2 nanoparticle was used with concentration ranging from 0.004 until 0.4 kg/m3 and boiling time of tb = 1, 3, 10, 20, 40, and 60 mins. Distilled water was used to observed BHT and CHF performance of different nanofluids boiling time and concentration configurations. Nucleate boiling heat transfer observed to deteriorate in upward facing heater, however; in contrast effect of enhancement for downward. Maximum enhancements of CHF for upward- and downward-facing heater are 2.1 and 1.9 times, respectively. Reduction of mean contact angle demonstrate enhancement on the critical heat flux for both upward-facing and downward-facing heater configuration. However, nucleate boiling heat transfer shows inconsistency in similar concentration with sequence of boiling time. For both downward- and upward-facing nanocoated heater's BHT and CHF, the optimum configuration denotes by C = 400 kg/m3 with tb = 1 min which shows the best increment of boiling curve trend with lowest wall superheat ΔT = 25 K and critical heat flux enhancement of 2.02 times.

Study on Subcooled-Forced Flow Boiling Heat Transfer and Critical Heat Flux of Solid-Water Two-Phase Mixture

1999 ◽  
Author(s):  
Yasuo Koizumi ◽  
Hiroyasu Ohtake ◽  
Manabu Mochizuki
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Liquid Layer ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Forced Flow ◽  
Superheated Liquid ◽  
Flow Boiling Heat Transfer

Abstract The effect of solid particle introduction on subcooled-forced flow boiling heat transfer and a critical heat flux was examined experimentally. In the experiment, glass beads of 0.6 mm diameter were mixed in subcooled water. Experiments were conducted in a range of the subcooling of 40 K, a velocity of 0.17–6.7 m/s, a volumetric particle ratio of 0–17%. When particles were introduced, the growth of a superheated liquid layer near a heat trasnsfer surface seemed to be suppressed and the onset of nucleate boiling was delayed. The particles promoted the condensation of bubbles on the heat transfer surface, which shifted the initiation of a net vapor generation to a high heat flux region. Boiling heat trasnfer was augmented by the particle introduction. The suppression of the growth of the superheated liquid layer and the promotion of bubble condensation and dissipation by the particles seemed to contribute that heat transfer augmentation. The wall superheat at the critical heat flux was elevated by the particle introduction and the critical heat flux itself was also enhanced. However, the degree of the critical heat flux improvement was not drastic.

scholarly journals Determination of Pool Boiling Critical Heat Flux Enhancement in Nanofluids

2007 ◽  
Author(s):  
Bao H. Truong
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Porous Coating ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Sem Images ◽  
Heat Transfer Coefficients ◽  
Nucleate Boiling Heat Transfer

Nanofluids are engineered colloids composed of nano-size particles dispersed in common fluids such as water or refrigerants. Using an electrically controlled wire heater, pool boiling Critical Heat Flux (CHF) of Alumina and Silica water-based nanofluids of concentration less than or equal to 0.1 percent by volume were measured. Silica nanofluids showed a CHF enhancement up to 68% and there seems to be a monotonic relationship between the nanoparticle concentration and the magnitude of enhancement. Alumina nanofluids had a CHF enhancement up to 56% but the peak occurred at the intermediate concentration. The boiling curves in nanofluid were found to shift to the left of that of water and correspond to higher nucleate boiling heat transfer coefficients in the two-phase flow regime. Scanning Electron Microscopy (SEM) images show a porous coating layer of nanoparticles on wires subjected to nanofluid CHF tests. These coating layers change the morphology of the heater’s surface, and are responsible for the CHF enhancement. The thickness of the coating was estimated using SEM and was found ranging from 3.0 to 6.0 micrometers for Alumina, and 3.0 to 15.0 micrometers for Silica.

Two-Phase Pipe Quenching Correlations for Liquid Nitrogen and Liquid Hydrogen

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
S. R. Darr ◽  
J. W. Hartwig ◽  
J. Dong ◽  
H. Wang ◽  
A. K. Majumdar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Liquid Nitrogen ◽  
Critical Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Liquid Hydrogen ◽  
Two Phase ◽  
Cryogenic Flow ◽  
Two Phase Heat Transfer

Recently, two-phase cryogenic flow boiling data in liquid nitrogen (LN2) and liquid hydrogen (LH2) were compared to the most popular two-phase correlations, as well as correlations used in two of the most widely used commercially available thermal/fluid design codes in Hartwig et al. (2016, “Assessment of Existing Two Phase Heat Transfer Coefficient and Critical Heat Flux on Cryogenic Flow Boiling Quenching Experiments,” Int. J. Heat Mass Transfer, 93, pp. 441–463). Results uncovered that the correlations performed poorly, with predictions significantly higher than the data. Disparity is primarily due to the fact that most two-phase correlations are based on room temperature fluids, and for the heating configuration, not the quenching configuration. The penalty for such poor predictive tools is higher margin, safety factor, and cost. Before control algorithms for cryogenic transfer systems can be implemented, it is first required to develop a set of low-error, fundamental two-phase heat transfer correlations that match available cryogenic data. This paper presents the background for developing a new set of quenching/chilldown correlations for cryogenic pipe flow on thin, shorter lines, including the results of an exhaustive literature review of 61 sources. New correlations are presented which are based on the consolidated database of 79,915 quenching points for a 1.27 cm diameter line, covering a wide range of inlet subcooling, mass flux, pressure, equilibrium quality, flow direction, and even gravity level. Functional forms are presented for LN2 and LH2 chilldown correlations, including film, transition, and nucleate boiling, critical heat flux, and the Leidenfrost point.

Critical Heat Flux and Onset of Nucleate Boiling Tests in a Finned Rod Bundle

2004 ◽  
Vol 148 (3) ◽  
pp. 287-293
Author(s):  
Hee Taek Chae ◽  
Jong Hark Park ◽  
Heonil Kim ◽  
Soon Heung Chang
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Nucleate Boiling ◽  
Rod Bundle

On the Mechanism of Pool Boiling Critical Heat Flux Enhancement in Nanofluids

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
Hyungdae Kim ◽  
Ho Seon Ahn ◽  
Moo Hwan Kim
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Heated Surface ◽  
Pure Water ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Titania Nanoparticles ◽  
Nanoparticle Layer ◽  
Wall Superheat ◽  
Dry Spot

The pool boiling characteristics of water-based nanofluids with alumina and titania nanoparticles of 0.01 vol % were investigated on a thermally heated disk heater at saturated temperature and atmospheric pressure. The results confirmed the findings of previous studies that nanofluids can significantly enhance the critical heat flux (CHF), resulting in a large increase in the wall superheat. It was found that some nanoparticles deposit on the heater surface during nucleate boiling, and the surface modification due to the deposition results in the same magnitude of CHF enhancement in pure water as for nanofluids. Subsequent to the boiling experiments, the interfacial properties of the heater surfaces were examined using dynamic wetting of an evaporating water droplet. As the surface temperature increased, the evaporating meniscus on the clean surface suddenly receded toward the liquid due to the evaporation recoil force on the liquid-vapor interface, but the nanoparticle-fouled surface exhibited stable wetting of the liquid meniscus even at a remarkably higher wall superheat. The heat flux gain attainable due to the improved wetting of the evaporating meniscus on the fouled surface showed good agreement with the CHF enhancement during nanofluid boiling. It is supposed that the nanoparticle layer increases the stability of the evaporating microlayer underneath a bubble growing on a heated surface and thus the irreversible growth of a hot/dry spot is inhibited even at a high wall superheat, resulting in the CHF enhancement observed when boiling nanofluids.

Study on DNB-Type Critical Heat Flux With Chopper-Cosine Axial Heat Flux Distributions

2014 ◽  
Author(s):  
Dawei Zhao ◽  
Wanyu Xiong ◽  
Wenxing Liu ◽  
Jianjun Xu
Keyword(s):  
Heat Flux ◽  
Critical Heat Flux ◽  
Present Model ◽  
Reactor Design ◽  
Nucleate Boiling ◽  
Uniform Heat Flux ◽  
Good Prediction ◽  
Uniform Heating ◽  
Comparison Results ◽  
Axial Heat

Departure from nucleate boiling (DNB) type critical heat flux (CHF) is one of most important thermal criteria for nuclear reactor design. Concerning on the typical chopper-cosine heat flux profile at reactor core, it is of great significance to predict the CHF under non-uniform heating conditions for reactor design and the performance promotion of reactor system. Some correction factors are proposed for the prediction of CHF with non-uniform axial power shapes. In this study, a mechanistic DNB-type CHF model has been developed on the basis of liquid sublayer dryout mechanism. The non-uniform axial heat flux is taken into account of upstream memory effect on boiling crisis in this model. The predictions of present model and Tong’s non-uniform heat flux shape factor method are compared with the experimental results in the vertical tube with chopper-cosine axial heat flux distributions. The comparison results show the present model has fairly good prediction capability for DNB-type CHF under non-uniform heating condition.

Sign in / Sign up

Export Citation Format

Share Document