Preliminary Feasibility Study of Groundwater Source Geothermal Heat Pumps in Mason County and the American Bottoms Area, Illinois

2014 ◽  
Author(s):  
Xinli Lu ◽  
David R. Larson ◽  
Thomas R. Holm
Keyword(s):  
Ground Surface ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Weather Data ◽  
Single Family ◽  
Geothermal Heat ◽  
Geothermal Heating ◽  
Heating And Cooling ◽  
Groundwater Source ◽  
Mason County

Groundwater source heat pumps exploit the difference between the ground surface temperature and the nearly constant temperature of shallow groundwater. This project characterizes two areas for geothermal heating and cooling potential, Mason County in central Illinois and the American Bottoms area in southwestern Illinois. Both areas are underlain by thick sand and gravel aquifers and groundwater is readily available. Weather data, including monthly high and low temperatures and heating and cooling degree days, were compiled for both study areas. The heating and cooling requirements for a single-family house were estimated using two independent models that use weather data as input. The groundwater flow rates needed to meet these heating and cooling requirements were calculated using typical heat pump coefficient of performance values. The groundwater in both study areas has fairly high hardness and iron concentrations and is close to saturation with calcium and iron carbonates. Using the groundwater for cooling may induce the deposition of scale containing one or both of these minerals.

Modeling and Design of Building-Integrated Thermoelectrics

2011 ◽  
Author(s):  
Leon M. Headings ◽  
Gregory N. Washington
Keyword(s):  
Thermal Response ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Conventional Heating ◽  
Net Energy ◽  
Arbitrary Boundary ◽  
Heating And Cooling ◽  
Temperature Oscillations ◽  
Wall Structures ◽  
And Control

The goal of this research is to develop a framework for replacing conventional heating and cooling systems with distributed, continuously and electrically controlled, building-integrated thermoelectric (BITE) heat pumps. The coefficient of performance of thermoelectric heat pumps increases as the temperature difference across them decreases and as the amplitude of temperature oscillations decreases. As a result, this research examines how thermal insulation and mass elements can be integrated with thermoelectrics as part of active multi-layer structures in order to minimize net energy consumption. In order to develop BITE systems, an explicit finite volume model was developed to model the dynamic thermal response of active multi-layer wall structures subjected to arbitrary boundary conditions (interior and exterior temperatures and interior heat loads) and control algorithms. Using this numerical model, the effects of wall construction on net system performance were examined. These simulation results provide direction for the ongoing development of BITE systems.

scholarly journals Heat pump systems: A mini review

2021 ◽  
Vol 4 (2) ◽  
pp. 73-81
Author(s):  
Mohammad Omar Temori ◽  
František Vranay
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Cost Savings ◽  
Electrical Energy ◽  
Primary Energy ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Heating And Cooling ◽  
Ground Source ◽  
Reduce Electricity Consumption

In this work, a mini review of heat pumps is presented. The work is intended to introduce a technology that can be used to income energy from the natural environment and thus reduce electricity consumption for heating and cooling. A heat pump is a mechanical device that transfers heat from one environmental compartment to another, typically against a temperature gradient (i.e. from cool to hot). In order to do this, an energy input is required: this may be mechanical, electrical or thermal energy. In most modern heat pumps, electrical energy powers a compressor, which drives a compression - expansion cycle of refrigerant fluid between two heat exchanges: a cold evaporator and a warm condenser. The efficiency or coefficient of performance (COP), of a heat pump is defined as the thermal output divided by the primary energy (electricity) input. The COP decreases as the temperature difference between the cool heat source and the warm heat sink increases. An efficient ground source heat pump (GSHP) may achieve a COP of around 4. Heat pumps are ideal for exploiting low-temperature environmental heat sources: the air, surface waters or the ground. They can deliver significant environmental (CO2) and cost savings.

scholarly journals Geothermal air conditioning: typical applications using deep-warm and shallow-cool reservoirs for cooling in Perth, Western Australia

2014 ◽  
Vol 5 ◽  
pp. A10
Author(s):  
Peter B. Whittaker ◽  
Xiaolin Wang ◽  
Klaus Regenauer-Lieb ◽  
David Blair ◽  
Hui Tong Chua
Keyword(s):  
Western Australia ◽  
Alternative Energy ◽  
Cooling Water ◽  
Geothermal Gradient ◽  
Heat Pumps ◽  
The Other ◽  
Plate Boundaries ◽  
Climate Control ◽  
Geothermal Heat ◽  
Heating And Cooling

Geothermal heat is a sustainable form of alternative energy, commonly associated with the production of electricity along tectonic plate boundaries and in volcanically active zones. Outside of these special regions however it is rare to find a geothermal gradient high enough to achieve pay back on projects for generating electricity. On the other hand regions containing sedimentary aquifers are far more common and these aquifers frequently have a sufficiently high temperature gradient to make direct use of the thermal energy attractive. Meanwhile highly permeable aquifers occurring at shallow depths are possible sources for cooling water or can be both heat sources and sinks when used in combination with heat pumps. We provide a case study for the use of thermally driven absorption chillers on the University of Western Australia campus in Perth and discuss two ongoing projects: one for the heating and cooling of the offices of the Australian Resources Research Council using a reversible heat pump and the other the climate control of the planned Australian International Gravitational Observatory.

scholarly journals Energy analysis, numerical simulations and intervention proposals for a NZEB industrial building: the “Loccioni Leaf Lab” case study

2021 ◽  
Vol 238 ◽  
pp. 06004
Author(s):  
Ettore Stamponi ◽  
Nicola Lattanzi ◽  
Francesco Giorgini ◽  
Fabio Serpilli ◽  
Sergio Montelpare ◽  
...  
Keyword(s):  
Smart Grid ◽  
High Performance ◽  
Energy Performance ◽  
Heat Pumps ◽  
Weather Data ◽  
Industrial Building ◽  
Dynamic Simulations ◽  
Heating And Cooling ◽  
Energy Consumptions

The object of this paper is the “Loccioni Leaf Lab”, an industrial nZEB connected to a thermal and electric smart grid. Having nZEB buildings connected to a smart grid offers the possibility of maximizing the benefits that can be obtained by optimal regulation of the grid itself, providing excellent economic and energy results. The case study, which hosts offices and workers operating on test benches, features high performance envelope, solar photovoltaic systems, groundwater heat pumps and a hightechnology control and monitoring system. In order to analyse HVAC-related energy consumptions, the building was modelled using DesignBuilder and EnergyPlus software. The annual dynamic simulations for the assessment of building thermal-energy performance were carried out using available monitored weather data (2019). The model was validated according to ASHRAE guidelines, comparing the outputs of the software with data collected and stored by Company internal database. In the validation process, mean indoor air temperatures of several zones and heating and cooling energy consumptions were considered as key outputs. The validated model has then been used to suggest optimization strategies and to analyse the results obtained with proposed interventions in terms of energy saving.

scholarly journals Optimised Heat Pump Management for Increasing Photovoltaic Penetration into the Electricity Grid

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1571
Author(s):  
Cristian Sánchez ◽  
Lionel Bloch ◽  
Jordan Holweger ◽  
Christophe Ballif ◽  
Nicolas Wyrsch
Keyword(s):  
Heat Pump ◽  
Renewable Energy Sources ◽  
Pump Energy ◽  
Thermal Storage ◽  
Heat Pumps ◽  
Photovoltaic System ◽  
Coefficient Of Performance ◽  
Single Family ◽  
Electricity Grid ◽  
Nonlinear Optimisation

Advanced control of heat pumps with thermal storage and photovoltaics has recently been promoted as a promising solution to help decarbonise the residential sector. Heat pumps and thermal storage offer a valuable flexibilisation mean to integrate stochastic renewable energy sources into the electricity grid. Heat pump energy conversion is nonlinear, leading to a challenging nonlinear optimisation problem. However, issues like global optimum uncertainty and the time-consuming methods of current nonlinear programming solvers draw researchers to linearise heat pump models that are then implemented in faster and globally convergent linear programming solvers. Nevertheless, these linearisations generate some inaccuracies, especially in the calculation of the heat pump’s coefficient of performance ( C O P ). In order to solve all of these issues, this paper presents a heuristic control algorithm (HCA) to provide a fast, accurate and near-optimal solution to the original nonlinear optimisation problem for a single-family house with a photovoltaic system, using real consumption data from a typical Swiss house. Results highlight that the HCA solves this optimisation problem up to 1000 times faster, yielding an operation that is up to 49% cheaper and self-consumption rates that are 5% greater than other nonlinear solvers. Comparing the performance of the HCA and the linear solver intlinprog, it is shown that the HCA provides more accurate heat pump control with an increase of up to 9% in system Operating Expense OPEX and a decrease of 8% in self-consumption values.

Dynamic Simulation of Organic Rankine Cycle-Assisted Ground-Source Heat Pump Based Micro-Cogeneration System in Cold Climates: A Case Study in Canada

2021 ◽  
Author(s):  
Wahiba Yaïci ◽  
Evgueniy Entchev ◽  
Michela Longo
Keyword(s):  
Storage Temperature ◽  
Organic Rankine Cycle ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Net Energy ◽  
Combined System ◽  
Ground Source Heat Pumps ◽  
Heating And Cooling ◽  
Ground Source ◽  
Cogeneration System

Abstract As the energy needed for heating and cooling involves a substantial amount (> 80%) of residential energy utilisation in Canada, there is a demand for ultra-efficient energy systems for heating, cooling, and power generation. Two efficient systems to assist these systems are ground-source heat pumps (GSHPs) and organic Rankine cycles (ORCs). Of particular interest, this paper presents the integration of these two systems in a parallel configuration. A transient simulation model developed in TRNSYS program has been utilised to simulate the thermal performance of the combined ORC-GSHP based microco/trigeneration system. This later supplies heating and cooling to the residential load during the heating mode as required, with the capability to switch to a charging mode, where the ORC unit is directly coupled to the ground heat exchanger (GHE), which operates as a thermal energy storage and provides energy to the GSHP. The feasibility of this combined system configuration as well as its comparison with a conventional GSHP system are investigated for use in residential application in Ottawa, Canada temperature conditions. Results disclosed that the proposed micro-cogeneration system had the operating hours and performance of the GSHP improved by the addition of the ORC unit, resulting in about 11.8% reduction in hours in the colder city of Ottawa. The COP (coefficient of performance) of the GSHP system sustained a much higher value overall due to the addition of the ORC system to maintain the GHE storage temperature. In terms of net energy reduction between the conventional GSHP system and the ORC-assisted one, results revealed that Ottawa had energy usage reduction of 82.0%, demonstrating that the addition of an ORC to provide heating and recharge the GHE of a GSHP system has many advantages that could be accomplished by the end-user.

scholarly journals Modeling of an Air Conditioning System with Geothermal Heat Pump for a Residential Building

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Silvia Cocchi ◽  
Sonia Castellucci ◽  
Andrea Tucci
Keyword(s):  
Heat Pump ◽  
Air Conditioning ◽  
Residential Building ◽  
Heat Pumps ◽  
Geothermal Heat ◽  
Air Conditioning System ◽  
Heating And Cooling ◽  
Ground Source ◽  
Geothermal Heat Pump ◽  
Geothermal Plant

The need to address climate change caused by greenhouse gas emissions attaches great importance to research aimed at using renewable energy. Geothermal energy is an interesting alternative concerning the production of energy for air conditioning of buildings (heating and cooling), through the use of geothermal heat pumps. In this work a model has been developed in order to simulate an air conditioning system with geothermal heat pump. A ground source heat pump (GSHP) uses the shallow ground as a source of heat, thus taking advantage of its seasonally moderate temperatures. GSHP must be coupled with geothermal exchangers. The model leads to design optimization of geothermal heat exchangers and to verify the operation of the geothermal plant.

scholarly journals Practical study on heat pump enhancement by the solar energy

2021 ◽  
Vol 288 ◽  
pp. 01069
Author(s):  
Omar Abdulhadi Mustafa Almohammed ◽  
Farida Mizkhatovna Philippova ◽  
Fouad Ibrahim Alhajj Hassan ◽  
Nail Farilovich Timerbaev ◽  
Anatoliy Anatolyevich Fomin
Keyword(s):  
Heat Exchanger ◽  
Solar Energy ◽  
Heat Pump ◽  
Technical College ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Laboratory Model ◽  
Additional Heat ◽  
Heating And Cooling ◽  
Positive Effect

The heat pumps system is one of the most remarkable system that is widely used around the world, their capacity is different according to necessity. The energy consumption in those systems will limit their effectiveness. This study will try to prove the positive reactance of the new changes (the additional heat exchanger) on the heat pump work, where the power consumption will reduce about (13-17%). The study includes the experimental results of the laboratory model, which has been manufactured in the laboratories of the technical college of Mosul/Northern technical university-Iraq. The model consists of the heat pump that was improved by using the additional heat exchanger, its duty is to heat the refrigerant before entering the compressor, by using solar energy. The results of this work prove the positive effect of the additional heat exchanger, on the coefficient of performance of the heat pump, in both modes of heating and cooling. The conclusions are useful to the industries that deal with heat pumps.

Development of design guidelines for thermo-active foundations

2017 ◽  
Vol 27 (6) ◽  
pp. 805-817 ◽  
Author(s):  
Byung C. Kwag ◽  
Moncef Krarti
Keyword(s):  
Heat Pump ◽  
Heat Pumps ◽  
Design Guidelines ◽  
Conventional Heating ◽  
Ground Source Heat Pump ◽  
External Energy ◽  
Geothermal Heat ◽  
Ground Source Heat Pumps ◽  
Heating And Cooling ◽  
Ground Source

Ground medium can be utilized as a direct energy source to heat and cool buildings. In particular, ground source heat pump systems take advantage of the year-round mild deep earth temperature without a significant reliance on any external energy sources. However, the high installation cost of ground source heat pumps associated with high drilling cost of vertical boreholes often make these systems less cost-effective compared to conventional heating and cooling systems. Thermo-active foundations can be a viable solution to reduce ground source heat pump high installation costs by embedding heat exchangers within building foundation structures. Compared to ground source heat pumps, only limited analyses and research studies have been reported for thermo-active foundations especially for the US climates. In particular, no specific design guidelines have been reported for thermo-active foundations especially for US climates. In this paper, a simplified design approach was developed and applied for specifying geothermal heat pump size and heat exchanger loop length to meet all or part of building heat and cooling thermal loads. The developed guidelines would thus provide a proper design guide for installation of thermo-active foundations for heating and cooling of both US residential and commercial buildings.

Sign in / Sign up

Export Citation Format

Share Document