Dry Sliding Tribological Behavior of Columnar-Grained Fe2B Intermetallic Compound Under Different Loads

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Kemin Li ◽  
Zhifu Huang ◽  
Ting Min ◽  
Jiamei Liu ◽  
Lei Zhang ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Intermetallic Compound ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Laser Scanning ◽  
Tribological Behavior ◽  
Normal Load ◽  
Dry Sliding ◽  
Dynamic Friction Coefficient ◽  
Worn Surface

The dry sliding tribological behavior of a columnar-grained Fe2B intermetallic compound under different normal loads was evaluated by scanning electron microscopy (SEM), XPS, and 3D laser scanning microscope. The results indicated that under a load of 12 N, after a 35 min break-in period, the dynamic friction coefficient decreased from 0.78 to about 0.6 and this low value was maintained until the end of test. When the normal load increased from 4 N to 20 N, both the average friction coefficient and wear rate values initially decreased and then increased. The lowest values of the average friction coefficient and wear rate were obtained under a load of 12 N. As the load increased from 4 N to 12 N, a complete film formed on worn surface. Nevertheless, when the load increased to 16 N, severe self-induced vibration occurred and a corrugated ribbon appeared on the surface. Furthermore, severe damage on the worn surface was caused by cycling vibration under the 20 N load. Under 4 N and 12 N, the main wear mechanism was abrasive wear, while under a load of 20 N, fracture wear and abrasive wear were the mian wear mechanisms. The friction products were composed of B2O3, H3BO3, SiO2, and FexOy. More specifically, Fe2O3 was generated under 4 N load, Fe2O3 and Fe3O4 were produced under 12 N load, and the mixture of FeO, Fe2O3, and Fe3O4 appeared under 20 N load.

scholarly journals Modeling and Analysis for Wear Performance in Dry Sliding of Epoxy/Glass/PTW Composites Using Full Factorial Techniques

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
M. Sudheer ◽  
Ravikantha Prabhu ◽  
K. Raju ◽  
Thirumaleshwara Bhat
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Hybrid Composites ◽  
Normal Load ◽  
Glass Fibers ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Wear Performance ◽  
Full Factorial

The dry sliding friction and wear behavior of epoxy hybrid composites reinforced with glass fibers and a varying amount of potassium titanate whiskers (PTWs) fabricated by vacuum hand layup method were studied. The influence of normal load, sliding velocity, and whisker content on both friction coefficient and specific wear rate was investigated on a pin-on-disc machine. The tests were conducted at ambient conditions based on the 3 × 3 (3 factors at 3 levels) full factorial design. Analysis of variance (ANOVA) was performed to obtain the contribution of control parameters on friction coefficient and wear rate. The density and hardness of the composites were found to be enhanced with the PTW loading. The friction coefficient and wear resistance of the hybrid composites were found to be improved with the whisker content and were also greatly influenced by normal load and sliding velocity. A correlation between dry sliding wear behaviors of composites with wear parameters was obtained by multiple regressions. The worn out surface of selected samples was observed under scanning electron microscope (SEM) to identify wear mechanisms. This study revealed that the addition of the ceramic microfillers such as PTW improves the wear performance of the epoxy/glass polymer composites significantly.

High-Speed Dry Tribological Behaviors of CrNiMo Steel in Nitrogen and Oxygen Atmospheres

2011 ◽  
Vol 704-705 ◽  
pp. 877-885
Author(s):  
San Ming Du ◽  
Yong Zhen Zhang ◽  
Bao Shangguan
Keyword(s):  
Abrasive Wear ◽  
Tribological Properties ◽  
Wear Mechanism ◽  
Wear Mechanisms ◽  
High Speed ◽  
Normal Load ◽  
Dry Sliding ◽  
Tribological Behaviors ◽  
Electron Dispersion ◽  
Worn Surface

Abstract: In this article, the high-speed dry sliding tribological behaviors of CrNiMo steel against brass in nitrogen and oxygen atmospheres are investigated using a pin-on-disc tribometer. The worn surface is characterized by scanning electron microscopy and electron dispersion spectrums analysis. The wear mechanisms of CrNiMo steel are also analyzed. The results indicate that the tribological properties of CrNiMo steel are coincidental with the law of dry sliding of metal, where the friction coefficients decreases with an increase in sliding speed and with normal load. However, the atmosphere has obvious effects on the tribological properties of CrNiMo steel. In the sliding process, friction heat plays an important role on the tribological properties of materials in high-speed dry friction. The high-speed wear mechanism of CrNiMo steel varies at different atmospheres. In a nitrogen atmosphere, the wear mechanism of CrNiMo steel is mainly characterized by adhesion at a lower speed and load. When the speed and load are increased, melting trace is found in the worn surface accompanied by an abrasive wear. In an oxygen atmosphere, the mechanism is characterized by adhesion at a lower speed and load; with an increase in speed and load, it gradually transformed into oxidation wear and abrasive wear. The difference of the wear mechanisms in the different atmospheres and test parameters is primarily due to the transfer films formed on the contact surfaces of the sliding pairs. In our experimental conditions, the surface film is mainly the metal film in nitrogen, whereas, it is the oxide film in oxygen.

Wear Behavior of Polyester – Carbon Nanotubes Composites under Dry Sliding Ball-on-Flat Reciprocating Test

2015 ◽  
Vol 809-810 ◽  
pp. 1169-1174
Author(s):  
Adrian Cotet ◽  
Luminita Ciupagea ◽  
Dumitru Dima ◽  
Gabriel Andrei
Keyword(s):  
Carbon Nanotubes ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Behavior ◽  
Multiwall Carbon Nanotubes ◽  
Dry Sliding ◽  
Linear Wear ◽  
Linear Wear Rate ◽  
Multiwall Carbon

Friction coefficient and linear wear rate of polyester-carbon nanotubes composites were investigated through ball-on-flat reciprocating test, under dry sliding contact. Three types of nanoscopic fillers were used: multiwall carbon nanotubes (MWCNT), functionalized multiwall carbon nanotubes (MWCNT-COOH) and singlewall carbon nanotubes (SWCNT), with three values of weight content 0.1, 0.15 and 0.2 wt%. Comparative analysis was done for polyester and its composites tested over 14 m sliding distance, under three values of load, 30 N, 40 N and 50 N. Composites containing MWCNT underwent a decrease in friction coefficient and linear wear rate only in case of 50N loading. An improvement of wear behavior under 50N loading was obtained for the composite with 0.10 wt% functionalized carbon nanotubes. Generally, better values of wear rate at 50 N loading were recorded in case of composites with 0.15 wt% and 0.20 wt% MWCNT and SWCNT, respectively. Optical and electronic investigation of the worn surfaces revealed the occurrence of abrasive, adhesive and fatigue wear. Abrasive wear is due to the hard particles detached from the counterpart which produce scratches and furrows on sliding track. Adhesive wear results when soft particle of polymer are caught and blocked among the asperities of counterpart, and it develops over a local area, being influenced by temperature rise. Fatigue and abrasive wear are responsible for the formation of the 3rd body between contacting parts which affects the friction and wear behavior. Morphological analysis of worn surface showed the rise of transfer film that induces instability of wear parameters.

scholarly journals Tribological Behavior of Phenolic Resin-Based Friction Composites Filled with Graphite

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 742
Author(s):  
En Zhang ◽  
Fei Gao ◽  
Rong Fu ◽  
Yunzhuo Lu ◽  
Xiaoming Han ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Phenolic Resin ◽  
Adhesive Wear ◽  
Tribological Behavior ◽  
Dry Sliding ◽  
Transfer Layer ◽  
Fatigue Wear ◽  
The Stability ◽  
Peeling Off

In this paper, the influence of graphite (Gr) on the dry sliding tribological properties of phenolic resin (PF) composites was studied under different sliding speeds of 3.1–47.1 m/s. The wear mechanism was investigated by the observation of the morphology of the transfer layer during the dry sliding process. It was found that the addition of Gr could decrease the friction coefficient and wear rate effectively, and the friction coefficient and wear rate decreased with the increase of Gr content in the range of 10–30 vol.%. The dominant wear mechanisms of PF-based friction composites changed from adhesive wear to fatigue wear (in the form of peeling-off) in the high sliding speed condition after the addition of Gr. The addition of Gr effectively reduced the sensitivity of PF-based friction materials to sliding speeds, and thus enhanced the stability of the friction coefficient. When the content of Gr was above 20 vol.%, the stability of the friction coefficient was relatively steady.

Investigation of the Wear Behavior of High Strength and High Conductivity Cu-Cr-Zr Alloy under Dry Sliding

2015 ◽  
Vol 817 ◽  
pp. 661-666 ◽  
Author(s):  
Yuan Gao ◽  
Jin Chuan Jie ◽  
Peng Chao Zhang ◽  
Jian Zhang ◽  
Tong Min Wang ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Mass Loss ◽  
Wear Behavior ◽  
Normal Load ◽  
Specific Wear Rate ◽  
Dry Sliding Wear ◽  
Composition Analysis ◽  
Dry Sliding ◽  
Zr Alloy

The dry sliding wear behavior of Cu-Cr-Zr alloy prepared by electromagnetic horizontal continuous casting was investigated. The wear behavior of the studied alloy was discussed in terms of friction coefficient, mass loss/sliding, specific wear rate and wear mechanism. The results indicate that with the increasing normal load and sliding velocity, the friction coefficient of Cu-Cr-Zr alloy decreased monotonically, the mass loss/sliding and specific wear rate increased. By wear surface morphology and composition analysis, the wear mechanisms were discussed preliminary. Oxidation and abrasion mechanisms dominated at the lower sliding velocities and loads. Increasing loads and velocities led to a combination of oxidation and adhesion. Plastic deformation was dominant for the higher applied load and sliding velocities.

Tribological behaviors of the water-lubricated rubber bearings under different lubricated conditions

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Bin Xiao ◽  
Xiaolin Zheng ◽  
Yi Zhou ◽  
Dan Yao ◽  
Yang Wan
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Peer Review ◽  
Design Methodology ◽  
Tribological Behavior ◽  
Friction Test ◽  
Content Type ◽  
Rubber Bearing ◽  
Rubber Bearings ◽  
Worn Surface

Purpose This study aims to evaluate the tribological behavior of water-lubricated rubber bearings sliding against stainless steel under different lubricate conditions. Design/methodology/approach The water-lubricated rubber bearings under various normal loads and sliding speeds were carried out on the ring-block friction test, and the wear morphology is test conducted by using scanning electron microscope. Findings The results indicate that the surface of water-lubricated rubber bearings has a more alternative friction coefficient and wear rate under seawater than other lubricate conditions. The seawater not only acts as a lubricating medium but also brings microstructure while corroding the rubber interface, thereby further enhancing the lubricating effect and storing abrasive debris. Originality/value In this paper, tribological properties of the water-lubricated rubber bearing on ring-block friction test has been investigated. Water-lubricated rubber bearing was carried out on various lubricate conditions, and the friction coefficient, wear rate and worn surface were analyzed. Also, the effects of sliding speeds were investigated. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-06-2020-0204/

Research on Tribological Properties of Cast Iron at High-Speed Dry Sliding Condition

2014 ◽  
Vol 936 ◽  
pp. 2063-2067
Author(s):  
Chen Yue ◽  
Shang Guan Bao ◽  
Ying Yu Huang
Keyword(s):  
Cast Iron ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Tribological Properties ◽  
High Speed ◽  
Friction Material ◽  
Dry Sliding ◽  
Oxidative Wear ◽  
Wear Properties

The friction and wear properties of cast iron with different graphite morphologies and matrix microstructure were investigated at high speed dry sliding against GCr15 steel on the MMS-1G high-speed tribometer apparatus. The various wear micro-mechanisms and tribo-metallographic phases were studied by using scanning electron microscopy. The results show that as friction material, vermicular iron exhibits excellent comprehensive tribological properties. The friction coefficient of cast iron sliding against GCr15 decreases while the wear rate increases with the increase of sliding speed, friction coefficient and wear rate decline with the increase of pearlite content. Under the experimental condition, the main wear mechanisms of flake iron are abrasive wear, of vermicular iron are abrasive wear and oxidative wear and of nodular iron are oxidative wear, abrasive wear and fatigue spalling.

Tribological Properties of Ti3SnC2/Cu Composite

2014 ◽  
Vol 602-603 ◽  
pp. 519-522 ◽  
Author(s):  
Zai Ji Zhan ◽  
Dan Dan Zhang ◽  
Chang Hong Guo ◽  
Wei Chai
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Tribological Properties ◽  
Applied Load ◽  
Tribological Behavior ◽  
Oxidative Wear ◽  
The Matrix ◽  
Steel Balls

In this study, 5 wt. % Ti3SnC2/Cu composite was synthesized by hot pressed sintering, and its tribological properties against AISI52100 steel balls were investigated using a ball-on-disk wear tester. The effects of sliding speeds and applied loads on the tribological behavior of Ti3SnC2/Cu were studied. The results showed the wear rate of Ti3SnC2/Cu composite increased with the increase of applied load and decreased with increase of sliding speed. The main tribological mechanisms of Ti3SnC2/Cu were abrasive wear and slightly oxidative wear. The friction coefficient of Ti3SnC2/Cu composite was stable and much lower than that of Cu at the same conditions. The loads were effectively born by the Ti3SnC2particles and the wear resistance of the matrix was obviously improved.

scholarly journals High Temperature Dry Tribological Behavior of Nb-Microalloyed Bearing Steel 100Cr6

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5216 ◽  
Author(s):  
Yucheng Zhu ◽  
Jian Li ◽  
Chaolei Zhang ◽  
Wenjun Wang ◽  
Huan Wang
Keyword(s):  
High Temperature ◽  
Friction Coefficient ◽  
Abrasive Wear ◽  
Tribological Behavior ◽  
Steel Substrate ◽  
Wear Test ◽  
Bearing Steel ◽  
Wear Volume ◽  
Nb Content ◽  
Worn Surface

100Cr6 steel is one of the most widely used bearing steels and a representative of first-generation bearing steel. Many engineering applications require rolling bearings to run at a high temperature. Therefore, it is necessary to improve the high temperature properties of 100Cr6 steel. In this paper, the effect of Nb on high temperature dry tribological behavior, including worn surface and friction coefficient, was analyzed by a wear test when Nb content was 0.018% and 0.040%. The results show that the microstructure is refined gradually, the hardness is improved, and wear volume decreases by 31.8% at most with the increase of Nb content. At 50 °C, the friction coefficient of 100Cr6 steel can be reduced by adding a small amount of Nb, but this effect will be weakened if the content of Nb is too high. In addition, excess Nb increases the hard precipitation of NbC, which aggravates the abrasive wear and leads to the increase in the depth of the worn surface. At 125 °C, the effect of Nb on tribological properties is weaker. With the increase of temperature, the steel substrate softens, and the oxide particles increase, which aggravates the abrasive wear and oxidation wear and makes the wear volume increase significantly.

scholarly journals Experimental Study on the Transition between Static and Kinetic Frictions of Steel/Shale Pairs

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Qin Lian ◽  
Chunxu Yang ◽  
Jifei Cao
Keyword(s):  
Friction Coefficient ◽  
Normal Load ◽  
Critical Distance ◽  
Dynamic Friction ◽  
Stick Slip ◽  
Dynamic Friction Coefficient ◽  
The Coefficient Of Friction ◽  
The Difference ◽  
Stick Slip Motion ◽  
Insight Into

The transition between static and kinetic frictions of steel/shale pairs has been studied. It was found that the coefficient of friction decreased exponentially from static to dynamic friction coefficient with increasing sliding displacement. The difference between static and dynamic friction coefficients and the critical distance Dc under the dry friction condition is much larger than that under the lubricated condition. The transition from static to dynamic friction coefficient is greatly affected by the normal load, quiescent time, and sliding velocity, especially the lubricating condition. Maintaining continuous lubrication of the contact area by the lubricant is crucial to reduce or eliminate the stick-slip motion. The results provide an insight into the transition from static to dynamic friction of steel/shale pairs.

Sign in / Sign up

Export Citation Format

Share Document