Thermal Modeling of Extreme Heat Flux Microchannel Coolers for GaN-on-SiC Semiconductor Devices

2016 ◽  
Vol 138 (1) ◽  
Author(s):  
Hyoungsoon Lee ◽  
Damena D. Agonafer ◽  
Yoonjin Won ◽  
Farzad Houshmand ◽  
Catherine Gorle ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Working Fluid ◽  
Extensive Literature ◽  
High Electron ◽  
Flow Conditions ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Power Densities

Gallium nitride (GaN) high-electron-mobility transistors (HEMTs) dissipate high power densities which generate hotspots and cause thermomechanical problems. Here, we propose and simulate GaN-based HEMT technologies that can remove power densities exceeding 30 kW/cm2 at relatively low mass flow rate and pressure drop. Thermal performance of the microcooler module is investigated by modeling both single- and two-phase flow conditions. A reduced-order modeling approach, based on an extensive literature review, is used to predict the appropriate range of heat transfer coefficients associated with the flow regimes for the flow conditions. Finite element simulations are performed to investigate the temperature distribution from GaN to parallel microchannels of the microcooler. Single- and two-phase conjugate computational fluid dynamics (CFD) simulations provide a lower bound of the total flow resistance in the microcooler as well as overall thermal resistance from GaN HEMT to working fluid. A parametric study is performed to optimize the thermal performance of the microcooler. The modeling results provide detailed flow conditions for the microcooler in order to investigate the required range of heat transfer coefficients for removal of heat fluxes up to 30 kW/cm2 and a junction temperature maintained below 250 °C. The detailed modeling results include local temperature and velocity fields in the microcooler module, which can help in identifying the approximate locations of the maximum velocity and recirculation regions that are susceptible to dryout conditions.

scholarly journals EFFECT OF OIL ON HEAT TRANSFER OF MIXED REFRIGERANT BOILING IN EVAPORATOR TUBES IN REFRIGERATION MACNINES

2019 ◽  
pp. 88-93
Author(s):  
Alexey Vasilievich Ezhov ◽  
Sergey Sergeevich Ivanov ◽  
Aleksandr Bukin ◽  
Vladimir Grigorievich Bukin
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Flow Boiling ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Pipe Length ◽  
Heat Transfer Coefficients

The paper presents the results of an experimental study of the effect of oil on the heat transfer rate at boiling of mixed refrigerant R406A. Since the air conditioning system is not a pure refrigerant, but a mixture of oil with a concentration of up to 8%, such an amount of oil affects both hydrodynamics and heat exchange in the evaporators. The experimental work covers the entire range of regime parameters typical for these systems. There is shown the process of changing oil concentration in the pipe, as the working fluid boils, proving that most of the oil pipe does not impair the heat exchange in the course of two-phase flow boiling. Different modes of refrigerant R406A boiling dynamics have been defined, and each mode is given a quantitative assessment in terms of the effects of the oil and explaining of this effect on the fluid flow and heat transfer based on visual observations and the experiment results. The main factor of the effect is the freon-oil foam, which increases the proportion of the wetted surface in the wave and stratified modes and the heat transfer rate to 30%. A comparison of the heat transfer coefficients both in the cross section and along the pipe length has been performed, showing that the maximum change in heat transfer occurs in the upper part of the surface due to developing a dry wall on it and wetting it with freon-oil foam. A comparison of the heat transfer rate of pure refrigerant R406A has been done; the presence of oil in it shows that the effect of oil is complex and ambiguous. Calculation and criterion dependences for calculation of heat transfer coefficients in different modes have been proposed.

scholarly journals A Novel Generator Design Utilised for Conventional Ejector Refrigeration Systems

Energies ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7705
Author(s):  
Anas F. A. Elbarghthi ◽  
Mohammad Yousef Hdaib ◽  
Václav Dvořák
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Working Fluid ◽  
Convection Coefficient ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Cold Fluid ◽  
Cold Stream

Ejector refrigeration systems are rapidly evolving and are poised to become one of the most preferred cooling systems in the near future. CO2 transcritical refrigeration systems have inherently high working pressures and discharge temperatures, providing a large volumetric heating capacity. In the current research, the heat ejected from the CO2 gas cooler was proposed as a driving heating source for the compression ejector system, representing the energy supply for the generator in a combined cycle. The local design approach was investigated for the combined plate-type heat exchanger (PHE) via Matlab code integrated with the NIST real gas database. HFO refrigerants (1234ze(E) and 1234yf) were selected to serve as the cold fluid on the generator flowing through three different phases: subcooled liquid, a two-phase mixture, and superheated vapour. The study examines the following: the effectiveness, the heat transfer coefficients, and the pressure drop of the PHE working fluids under variable hot stream pressures, cold stream flow fluxes, and superheated temperatures. The integration revealed that the cold fluid mixture phase dominates the heat transfer coefficients and the pressure drop of the heat exchanger. By increasing the hot stream inlet pressure from 9 MPa to 12 MPa, the cold stream two-phase convection coefficient can be enhanced by 50% and 200% for R1234yf and R1234ze(E), respectively. Conversely, the cold stream two-phase convection coefficient dropped by 17% and 37% for R1234yf and R1234ze(E), respectively. The overall result supports utilising the ejected heat from the CO2 transcritical system, especially at high CO2 inlet pressures and low cold channel flow fluxes. Moreover, R1234ze(E) could be a more suitable working fluid because it possesses a lower pressure drop and bond number.

Parametric Dependence of Annular Flow Heat Transfer in Microgaps

2010 ◽  
Author(s):  
Emil Rahim ◽  
Avram Bar-Cohen
Keyword(s):  
Heat Transfer ◽  
Annular Flow ◽  
Forced Flow ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Channel Diameter ◽  
Parametric Dependence ◽  
Heat Transfer Coefficients ◽  
High Heat Transfer

Forced flow of refrigerants and dielectric liquids, undergoing phase change in a heated microgap channel between chips or in parallel microchannels in a compact cooler, is a promising candidate for the thermal management of advanced semiconductor devices. It has been found that Annular flow is the dominant flow regime in such miniature channels and that relatively high heat transfer coefficients are encountered in the moderate-to-high quality sections of such channels. Following a discussion of flow regimes and thermal characteristics of miniature channels, attention turns to exploring the parametric dependence of annular flow thermal transport in microgaps including the effects of channel diameter, mass flux, and working fluid on the two-phase heat transfer coefficients.

Forced-Convection Heat Transfer for Single and Two-Phase Helical Flow in a Solar Receiver

1986 ◽  
Vol 108 (1) ◽  
pp. 76-83 ◽  
Author(s):  
F. N. Vafaie ◽  
J. R. Dunn
Keyword(s):  
Heat Transfer ◽  
Convection Heat Transfer ◽  
Flow Conditions ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Water Steam ◽  
Heat Transfer Coefficients ◽  
Phase Water ◽  
Solar Receiver

The heat transfer characteristics of a single-tube, helically coiled receiver for a concentrating solar collector are presented. Heat transfer coefficients were measured for single and two-phase water-steam flow in a helical coil subjected to radiant heating for a range of flow conditions and radiant flux levels. Results are presented for both the local and average heat transfer coefficients in several flow regimes.

Choosing Working Fluid for Two-Phase Thermosyphon Systems for Cooling of Electronics

2003 ◽  
Vol 125 (2) ◽  
pp. 276-281 ◽  
Author(s):  
Bjo¨rn Palm ◽  
Rahmatollah Khodabandeh
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Air Cooling ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
And Performance ◽  
Cooling Of Electronics

The heat fluxes from electronic components are steadily increasing and have now, in some applications, reached levels where air-cooling is no longer sufficient. One alternative solution, which has received much attention during the last decade, is to use heat pipes or thermosyphons for transferring or spreading the dissipated heat. In this paper two-phase thermosyphon loops are discussed. Especially, the choice of fluid and its influence on the design and performance is treated. The discussion is supported by results from simulations concerning heat transfer and pressure drop. In general it is found that high-pressure fluids will give better performance and more compact designs as high-pressure results in higher boiling heat transfer coefficients and smaller necessary tube diameter.

Heat Transfer in Rotating Serpentine Coolant Passage With Ribbed Walls at Low Mach Numbers

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
Shang-Feng Yang ◽  
Je-Chin Han ◽  
Salam Azad ◽  
Ching-Pang Lee
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Low Mach Number ◽  
Heat Transfer Coefficients ◽  
Rotation Numbers ◽  
Wide Range ◽  
Mach Numbers

This paper experimentally investigates the effect of rotation on heat transfer in typical turbine blade serpentine coolant passage with ribbed walls at low Mach numbers. To achieve the low Mach number (around 0.01) condition, pressurized Freon R-134a vapor is utilized as the working fluid. The flow in the first passage is radial outward, after the 180 deg tip turn the flow is radial inward to the second passage, and after the 180 deg hub turn the flow is radial outward to the third passage. The effects of rotation on the heat transfer coefficients were investigated at rotation numbers up to 0.6 and Reynolds numbers from 30,000 to 70,000. Heat transfer coefficients were measured using the thermocouples-copper-plate-heater regional average method. Heat transfer results are obtained over a wide range of Reynolds numbers and rotation numbers. An increase in heat transfer rates due to rotation is observed in radially outward passes; a reduction in heat transfer rate is observed in the radially inward pass. Regional heat transfer coefficients are correlated with Reynolds numbers for nonrotation and with rotation numbers for rotating condition, respectively. The results can be useful for understanding real rotor blade coolant passage heat transfer under low Mach number, medium–high Reynolds number, and high rotation number conditions.

scholarly journals Heat Transfer Measurements for Rotating Turbine Discs

1989 ◽  
Author(s):  
G. Qureshi ◽  
M. H. Nguyen ◽  
N. R. Saad ◽  
R. N. Tadros
Keyword(s):  
Heat Transfer ◽  
Coolant Flow ◽  
Flow Conditions ◽  
Transfer Coefficients ◽  
Rotating Disc ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Rotating Discs ◽  
Turbine Disc ◽  
State Technique

To optimise the turbine disc weight and coolant flow requirements, the aspect of improving thermal analysis was investigated. As a consequence, an experimental investigation was undertaken to measure the rates of convective heat transfer. The constant temperature steady state technique was used to determine the local and average heat transfer coefficients on the sides of rotating discs. The effects of coolant flow rates, CW (3000 ≤ CW ≤ 18600) with two types of cavity in-flow conditions and of the rotational speeds, Reθ (from 4×105 to 1.86×106) on the disc heat transfer were studied and correlations developed. For a rotating disc in confined cavities with superimposed coolant flows, Nusselt numbers were found to be higher than those for the free rotating disc without confinement.

Forced Convective Boiling of Refrigerant HCFC123 in a Mini-Tube

2010 ◽  
Author(s):  
Koichi Araga ◽  
Keisuke Okamoto ◽  
Keiji Murata
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Mass Flux ◽  
Pool Boiling ◽  
Constant Heat Flux ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Convective Boiling ◽  
Frictional Pressure Drop ◽  
Heat Transfer Coefficients

This paper presents an experimental investigation of the forced convective boiling of refrigerant HCFC123 in a mini-tube. The inner diameters of the test tubes, D, were 0.51 mm and 0.30 mm. First, two-phase frictional pressure drops were measured under adiabatic conditions and compared with the correlations for conventional tubes. The frictional pressure drop data were lower than the correlation for conventional tubes. However, the data were qualitatively in accord with those for conventional tubes and were correlated in the form φL2−1/Xtt. Next, heat transfer coefficients were measured under the conditions of constant heat flux and compared with those for conventional tubes and for pool boiling. The heat transfer characteristics for mini-tubes were different from those for conventional tubes and quite complicated. The heat transfer coefficients for D = 0.51 mm increased with heat flux but were almost independent of mass flux. Although the heat transfer coefficients were higher than those for a conventional tube with D = 10.3 mm and for pool boiling in the low quality region, they decreased gradually with increasing quality. The heat transfer coefficients for D = 0.30 mm were higher than those for D = 0.51 mm and were almost independent of both mass flux and heat flux.

Sign in / Sign up

Export Citation Format

Share Document