Impact of Using Biodiesels of Different Origin and Additives on the Performance of a Stationary Diesel Engine

2000 ◽  
Vol 122 (4) ◽  
pp. 624-631 ◽  
Author(s):  
A. Serdari ◽  
K. Fragioudakis ◽  
S. Kalligeros ◽  
S. Stournas ◽  
E. Lois
Keyword(s):  
Diesel Engine ◽  
Fatty Acid Methyl Esters ◽  
Corn Oil ◽  
Methyl Esters ◽  
Raw Material ◽  
Biodiesel Production ◽  
Exhaust Emission ◽  
Fuel Blends ◽  
Different Types ◽  
Particulate Matter Emissions

With the exception of rape seed oil which is the principal raw material for biodiesel Fatty Acid Methyl Esters, (FAME) production, sunflower oil, corn oil, and olive oil, which are abundant in Southern Europe, along with some wastes, such as used frying oils, appear to be attractive candidates for biodiesel production. In this paper fuel consumption and exhaust emission measurements from a single cylinder, stationary diesel engine are described. The engine was fueled with fuel blends containing four different types of biodiesel, at proportions up to 100 percent; the further impact of the usage of two specific additives was also investigated. The four types of biodiesel appeared to have equal performance and irrespective of the raw material used for their production, their addition to the traditional diesel fuel improved the particulate matter emissions. The results improve further when specific additive combinations are used. [S0742-4795(00)00604-9]

Mango (Magnifera indica) seed oil grown in Dilla town as potential raw material for biodiesel production using NaOH- a homogeneous catalyst

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Diesel Engine ◽  
Physicochemical Properties ◽  
Seed Oil ◽  
Methyl Esters ◽  
Pollution Prevention ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Homogeneous Catalyst ◽  
Minimal Amount

Biodiesel produced by transesterification process from vegetable oils or animal fats is viewed as a promising renewable energy source. Now a day’s diminishing of petroleum reserves in the ground and increasing environmental pollution prevention and regulations have made searching for renewable oxygenated energy sources from biomasses. Biodiesel is non-toxic, renewable, biodegradable, environmentally benign, energy efficient and diesel substituent fuel used in diesel engine which contributes minimal amount of global warming gases such as CO, CO2, SO2, NOX, unburned hydrocarbons, and particulate matters. The chemical composition of the biodiesel was examined by help of GC-MS and five fatty acid methyl esters such as methyl palmitate, methyl stearate, methyl oleate, methyl linoleate and methyl linoleneate were identified. The variables that affect the amount of biodiesel such as methanol/oil molar ratio, mass weight of catalyst and temperature were studied. In addition to this the physicochemical properties of the biodiesel such as (density, kinematic viscosity, iodine value high heating value, flash point, acidic value, saponification value, carbon residue, peroxide value and ester content) were determined and its corresponding values were 87 Kg/m3, 5.63 Mm2/s, 39.56 g I/100g oil, 42.22 MJ/Kg, 132oC, 0.12 mgKOH/g, 209.72 mgKOH/g, 0.04%wt, 12.63 meq/kg, and 92.67 wt% respectively. The results of the present study showed that all physicochemical properties lie within the ASTM and EN biodiesel standards. Therefore, mango seed oil methyl ester could be used as an alternative to diesel engine.

scholarly journals RSM Based Optimization of Chemical and Enzymatic Transesterification of Palm Oil: Biodiesel Production and Assessment of Exhaust Emission Levels

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Muhammad Waseem Mumtaz ◽  
Hamid Mukhtar ◽  
Farooq Anwar ◽  
Nazamid Saari
Keyword(s):  
Palm Oil ◽  
Fatty Acid Methyl Esters ◽  
Methyl Esters ◽  
Biodiesel Production ◽  
Exhaust Emission ◽  
Biodiesel Blends ◽  
Enzymatic Transesterification ◽  
Novozyme 435 ◽  
Emission Behavior ◽  
Palm Oil Biodiesel

Current study presents RSM based optimized production of biodiesel from palm oil using chemical and enzymatic transesterification. The emission behavior of biodiesel and its blends, namely, POB-5, POB-20, POB-40, POB-50, POB-80, and POB-100 was examined using diesel engine (equipped with tube well). Optimized palm oil fatty acid methyl esters (POFAMEs) yields were depicted to be47.6±1.5, 92.7±2.5, and95.4±2.0% for chemical transesterification catalyzed by NaOH, KOH, and NaOCH3, respectively, whereas for enzymatic transesterification reactions catalyzed by NOVOZYME-435 and A. n. lipase optimized biodiesel yields were94.2±3.1and62.8±2.4%, respectively. Distinct decrease in particulate matter (PM) and carbon monoxide (CO) levels was experienced in exhaust emissions from engine operating on biodiesel blends POB-5, POB-20, POB-40, POB-50, POB-80, and POB-100 comparative to conventional petroleum diesel. Percentage change in CO and PM emissions for different biodiesel blends ranged from −2.1 to −68.7% and −6.2 to −58.4%, respectively, relative to conventional diesel, whereas an irregular trend was observed for NOx emissions. Only POB-5 and POB-20 showed notable reductions, whereas all other blends (POB-40 to POB-100) showed slight increase in NOx emission levels from 2.6 to 5.5% comparative to petroleum diesel.

scholarly journals RAPE SEED OIL TETRAHYDROFURFURYLESTERS

2015 ◽  
Vol 1 ◽  
pp. 46
Author(s):  
K. Malins ◽  
V. Kampars ◽  
R. Kampare ◽  
T. Rusakova
Keyword(s):  
Rapeseed Oil ◽  
Fossil Fuels ◽  
Raw Materials ◽  
Methyl Esters ◽  
Cetane Number ◽  
Food Prices ◽  
Raw Material ◽  
Biodiesel Production ◽  
Cold Filter Plugging Point ◽  
Mineral Oils

The transesterification of vegetable oil using various kinds of alcohols is a simple and efficient renewable fuel synthesis technique. Products obtained by modifying natural triglycerides in transesterification reaction substitute fossil fuels and mineral oils. Currently the most significant is the biodiesel, a mixture of fatty acid methyl esters, which is obtained in a reaction with methanol, which in turn is obtained from fossil raw materials. In biodiesel production it would be more appropriate to use alcohols which can be obtained from renewable local raw materials. Ethanol rouses interest as a possible reagent, however, its production locally is based on the use of grain and therefore competes with food production so it would implicitly cause increase in food prices. Another raw material option is alcohols that can be obtained from furfurole. Furfurole is obtained in dehydration process from pentose sugars which can be extracted from crop straw, husk and other residues of agricultural production. From furfurole the tetrahydrofurfuryl alcohol (THFA), a raw material for biodiesel, can be produced. By transesterifying rapeseed oil with THFA it would be possible to obtain completely renewable biodiesel with properties very close to diesel [2-4]. With the purpose of developing the synthesis of such fuel, in this work a three-stage synthesis of rapeseed oil tetrahydrofurfurylesters (ROTHFE) in sulphuric acid presence has been performed, achieving product with purity over 98%. The most important qualitative factors of ROTHFE have been determined - cold filter plugging point, cetane number, water content, Iodine value, phosphorus content, density, viscosity and oxidative stability.

scholarly journals Ethanol-Based Biodiesel from Waste Vegetable Oil

2007 ◽  
Vol 7 (1 & 2) ◽  
pp. 83
Author(s):  
Mary Grace M. Oliveros ◽  
Amiliza B. Baiting ◽  
Menchie G. Lumain ◽  
Maria Theresa I. Cabaraban
Keyword(s):  
Vegetable Oil ◽  
Fast Food ◽  
Fossil Fuels ◽  
Material Balance ◽  
Raw Material ◽  
Biodiesel Production ◽  
Exhaust Emission ◽  
Waste Vegetable Oil ◽  
Power Testing ◽  
Technological Analysis

Waste vegetable oil, mainly coming from frying residues, can be used as raw material to obtain a diesel fuel (biodiesel). Biodiesel, a nontoxic, biodegradable, diesel-like fuel, is an important energy alternative capable of decreasing environmental problems caused by the consumption of fossil fuels. The utilization of waste vegetable oils as raw material in biodiesel production was studied. Research was undertaken to establish the availability of used vegetable oil to supply a biodiesel process. It is intended that this work forms an academic study combined with an environmental and technological analysis of the merits of biodiesel as a sustainable fuel. Laboratory experimentation investigated the possibility of using waste vegetable oil from the local fast food chains, and potassium hydroxide as catalyst for the transesterification process. The cleaned waste vegetable oil undergoes transesterification for 4 hours, after which, the biodiesel is separated from the glycerin by gravity. Washing is necessary to remove residual catalyst or soap. Overall material balance for the process gives: 1 kg Waste Vegetable oil + 0.18 kg EtOH + 0.01 kg KOH → 0.74 kg Biodiesel + 0.44 kg Glycerin The biodiesel, in pure form (B100) and in 50% proportion (B50) with petroleum diesel, was run in an essentially unmodified Toyota 2C diesel engine. Smoke density (opacity) and CO exhaust emission both decreased with B50. However, Nox increased with B50. Fuel consumption during engine power testing is significantly greater using the biodiesel, but is also significantly reduced with B50.

scholarly journals Biodiesel production using co-solvents: a review

2020 ◽  
Vol 9 (1) ◽  
pp. e99911672
Author(s):  
George Simonelli ◽  
José Mario Ferreira Júnior ◽  
Carlos Augusto de Moraes Pires ◽  
Luiz Carlos Lobato dos Santos
Keyword(s):  
Potassium Hydroxide ◽  
Fatty Acid Methyl Esters ◽  
State Of The Art ◽  
Methyl Esters ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Review Of The Literature ◽  
Transfer Resistance ◽  
Acid Methyl ◽  
High Yields

Biodiesel is a renewable and biodegradable biofuel, generally produced by the fatty materials transesterification. Due to its importance in the diversification of the energy matrix of countries, various studies have been carried out to improve its production process. One of the technologies developed is the use of co-solvents in the process. The co-solvents decrease the mass transfer resistance between the oil and the alcohol during the chemical reaction. In this paper, a review of the literature on the biodiesel production using co-solvents was presented. The research gathered information about various studies that are relevant to the theme, aiming to show the state of the art, the substances most used as co-solvents, and the conditions of the process variables that result in high yields of fatty acid methyl esters (FAME). In the homogeneous basic catalysis of vegetable oils, potassium hydroxide is the most used catalyst. Its range of application normally varies from 0.5% to 1.8% in relation to the mass of oil. The reaction time may vary from 10 minutes to 2 hours, the temperature from 25 °C to 100 °C, the molar ratio (MR), from 3:1 to 12:1, and the amount of 30% (w/w) co-solvent, or in some cases up to 0.7:1 co-solvent to alcohol molar ratio.

scholarly journals Trends in Widely Used Catalysts for Fatty Acid Methyl Esters (FAME) Production: A Review

Catalysts ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1085
Author(s):  
Shafaq Nisar ◽  
Muhammad Asif Hanif ◽  
Umer Rashid ◽  
Asma Hanif ◽  
Muhammad Nadeem Akhtar ◽  
...  
Keyword(s):  
Fatty Acid ◽  
Large Scale ◽  
Heterogeneous Catalysts ◽  
Fatty Acid Methyl Esters ◽  
Low Cost ◽  
Methyl Esters ◽  
Acid Catalyst ◽  
Product Formation ◽  
Biodiesel Production ◽  
Acid Methyl

The effective transesterification process to produce fatty acid methyl esters (FAME) requires the use of low-cost, less corrosive, environmentally friendly and effective catalysts. Currently, worldwide biodiesel production revolves around the use of alkaline and acidic catalysts employed in heterogeneous and homogeneous phases. Homogeneous catalysts (soluble catalysts) for FAME production have been widespread for a while, but solid catalysts (heterogeneous catalysts) are a newer development for FAME production. The rate of reaction is much increased when homogeneous basic catalysts are used, but the main drawback is the cost of the process which arises due to the separation of catalysts from the reaction media after product formation. A promising field for catalytic biodiesel production is the use of heteropoly acids (HPAs) and polyoxometalate compounds. The flexibility of their structures and super acidic properties can be enhanced by incorporation of polyoxometalate anions into the complex proton acids. This pseudo liquid phase makes it possible for nearly all mobile protons to take part in the catalysis process. Carbonaceous materials which are obtained after sulfonation show promising catalytic activity towards the transesterification process. Another promising heterogeneous acid catalyst used for FAME production is vanadium phosphate. Furthermore, biocatalysts are receiving attention for large-scale FAME production in which lipase is the most common one used successfully This review critically describes the most important homogeneous and heterogeneous catalysts used in the current FAME production, with future directions for their use.

scholarly journals Biodiesel Production from Rubber Seed Oil by Transesterification Using a Co-solvent of Fatty Acid Methyl Esters

2018 ◽  
Vol 41 (5) ◽  
pp. 1013-1018 ◽  
Author(s):  
Hanh Ngoc Thi Le ◽  
Kiyoshi Imamura ◽  
Norie Watanabe ◽  
Masakazu Furuta ◽  
Norimichi Takenaka ◽  
...  
Keyword(s):  
Fatty Acid ◽  
Fatty Acid Methyl Esters ◽  
Seed Oil ◽  
Methyl Esters ◽  
Biodiesel Production ◽  
Rubber Seed Oil ◽  
Rubber Seed ◽  
Acid Methyl

scholarly journals Exhaust emission profiling of fatty acid methyl esters and NOx control studies using selective synthetic and natural additives

2018 ◽  
Vol 20 (3) ◽  
pp. 589-601 ◽  
Author(s):  
Saad Afzal ◽  
Muhammad Waseem Mumtaz ◽  
Umer Rashid ◽  
Muhammad Danish ◽  
Muhammad Asam Raza ◽  
...  
Keyword(s):  
Fatty Acid ◽  
Fatty Acid Methyl Esters ◽  
Methyl Esters ◽  
Exhaust Emission ◽  
Acid Methyl ◽  
Nox Control ◽  
Natural Additives

WASTE FRYING OIL TRANSESTERIFICATION TREATED BY STEAM DRAG METHOD

2018 ◽  
Vol 26 (26) ◽  
pp. 34-42
Author(s):  
Daniel Sena MARINS ◽  
Marcos Vinícius Oliveira CARDOSO ◽  
Mara Eliza SANTOS ◽  
Jeferson MASSINHAN
Keyword(s):  
Moisture Content ◽  
Conversion Rate ◽  
Large Scale ◽  
Methyl Esters ◽  
Frying Oil ◽  
Raw Material ◽  
Biodiesel Production ◽  
Scale Production ◽  
Residual Oil ◽  
Conversion Rates

Demand for diversified biodiesel feedstocks is high and increasing, but few are viable for large-scale production, and many of those selected compete with other sectors of the chemical industry. To improve energy and environmental sustainability, fatty acids from waste oils that are improperly disposed of and pollute the environment can be used for transesterification reactions. However, they need treatment to achieve high conversion rates. In this context, the aim of this work was to perform and analyze the treatment of residual frying oil with the evaporation and entrainment process, aiming at its use as raw material to obtain biodiesel (methyl esters) by a transesterification reaction. The physicochemical properties of the residual oil after treatment were characterized by moisture content, pH and the acidity, saponification, iodine, and peroxide index. The conversion rate of the residual oil to methyl esters was determined by 1H NMR analysis. After the treatment, the method of analysis of variance showed that the oil obtained a significant reduction of the saponification, iodine, peroxide and acidity indexes, being the acidity reduced from 9.36 to 7.85 mg KOH g-1. The moisture content of 0.733% and elevation of pH to 8.0. The conversion rate of fatty acid biodiesel of residual oil was 79.3 %, lower value of standards norms (ASTM, 2005; EN, 2008; ANP, 2014), showing that the assigned methodology for frying residual oil is inefficient in biodiesel production.

Sign in / Sign up

Export Citation Format

Share Document