Dynamic test compression using statistical coding

2002 ◽  
Author(s):  
H. Ichihara ◽  
A. Ogawa ◽  
T. Inoue ◽  
A. Tamura
Keyword(s):  
Dynamic Test ◽  
Test Compression ◽  
Statistical Coding

Techniques for Determining the Parameters of a Two-Dimensional Tire Model for the Study of Ride Comfort

1997 ◽  
Vol 25 (3) ◽  
pp. 187-213 ◽  
Author(s):  
F. Mancosu ◽  
G. Matrascia ◽  
F. Cheli
Keyword(s):  
Physical Properties ◽  
Ride Comfort ◽  
Dynamic Test ◽  
Longitudinal Direction ◽  
Tire Model ◽  
Rigid Ring ◽  
Ring Model ◽  
Mass Moment ◽  
A New Technique ◽  
And Performance

Abstract A rigid ring model of the tire for the study of in-plane dynamics and a new technique for determining the parameters of the model are presented in this paper. This model can be used for studying the comfort of vehicles, problems of driving, and braking problems in the longitudinal direction. Comparison with finite element models shows that the rigid ring model of the tire is capable of describing the in-plane eigenmode shapes in the frequency range of 0–130 Hz. The well-known “brush model,” integrated into the tire model, is introduced to take into account the slide phenomena in the contact patch. The parameters of the model can be correlated with the physical properties of the tire so that designers can take advantage of such a correlation in the development of new tires in terms of time, cost, and performance. The technique used to determine the parameters of the model for some automobile tires include the direct measurements of some physical properties (mass, moment of inertia, stiffness) and a method of identification applied on the results from a dynamic test. The model is able to predict experimental data in terms of natural frequencies and relative dampings. Results from the application of this technique on two tires are reported.

Enabling Electro-Optical Failure Analysis within Extreme Compression Test Architecture

2016 ◽  
Author(s):  
Rudolf Schlangen ◽  
Jon Colburn ◽  
Joe Sarmiento ◽  
Bala Tarun Nelapatla ◽  
Puneet Gupta
Keyword(s):  
Failure Analysis ◽  
Compression Test ◽  
Test Pattern ◽  
Pattern Generation ◽  
Output Data ◽  
Test Compression ◽  
Test Loop ◽  
On Chip ◽  
Test Architecture

Abstract Driven by the need for higher test-compression, increasingly many chip-makers are adopting new DFT architectures such as “Extreme-Compression” (XTR, supported by Synopsys) with on-chip pattern generation and MISR based compression of chain output data. This paper discusses test-loop requirements in general and gives Advantest 93k specific guidelines on test-pattern release and ATE setup necessary to enable the most established EFA techniques such as LVP and SDL (aka DLS, LADA) within the XTR test architecture.

Load Testing to Collapse Limit State of Barr Creek Bridge

2000 ◽  
Vol 1696 (1) ◽  
pp. 92-102 ◽  
Author(s):  
Nicholas Haritos ◽  
Anil Hira ◽  
Priyan Mendis ◽  
Rob Heywood ◽  
Armando Giufre
Keyword(s):  
Finite Element ◽  
Failure Modes ◽  
Flexural Rigidity ◽  
Load Capacity ◽  
Limit State ◽  
Dynamic Test ◽  
Service Condition ◽  
Flat Slab ◽  
Testing Program ◽  
Static Testing

VicRoads, the road authority for the state of Victoria, Australia, has been undertaking extensive research into the load capacity and performance of cast-in-place reinforced concrete flat slab bridges. One of the key objectives of this research is the development of analytical tools that can be used to better determine the performance of these bridges under loadings to the elastic limit and subsequently to failure. The 59-year-old Barr Creek Bridge, a flat slab bridge of four short continuous spans over column piers, was made available to VicRoads in aid of this research. The static testing program executed on this bridge was therefore aimed at providing a comprehensive set of measurements of its response to serviceability level loadings and beyond. This test program was preceded by the performance of a dynamic test (a simplified experimental modal analysis using vehicular excitation) to establish basic structural properties of the bridge (effective flexural rigidity, EI) and the influence of the abutment supports from identification of its dynamic modal characteristics. The dynamic test results enabled a reliably tuned finite element model of the bridge in its in-service condition to be produced for use in conjunction with the static testing program. The results of the static testing program compared well with finite element modeling predictions in both the elastic range (serviceability loadings) and the nonlinear range (load levels taken to incipient collapse). Observed collapse failure modes and corresponding collapse load levels were also found to be predicted well using yield line theory.

scholarly journals The Performance of CR180IF and DP600 Laser Welded Steel Sheets under Different Strain Rates

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1553
Author(s):  
Mária Mihaliková ◽  
Kristína Zgodavová ◽  
Peter Bober ◽  
Anna Špegárová
Keyword(s):  
Sheet Steel ◽  
Testing Machine ◽  
Dynamic Test ◽  
Tensile Tests ◽  
Joint Surface ◽  
Strain Rates ◽  
Interstitial Free ◽  
Welded Steel ◽  
Steel Sheets ◽  
Static Tensile

The presented research background is a car body manufacturer’s request to test the car body’s components welded from dissimilar steel sheets. In view of the vehicle crew’s protection, it is necessary to study the static and dynamic behavior of welded steels. Therefore, the influence of laser welding on the mechanical and dynamical properties, microstructure, microhardness, and welded joint surface roughness of interstitial free CR180IF and dual-phase DP600 steels were investigated. Static tensile tests were carried out by using testing machine Zwick 1387, and dynamic test used rotary hammer machine RSO. Sheet steel was tested at different strain rates ranging from 10−3 to 103 s−1. The laser welds’ microstructure and microhardness were evaluated in the base metal, heat-affected zone, and fusion zone. The comprehensive analysis also included chemical analysis, fracture surface analysis, and roughness measurement. The research results showed that the strain rate had an influence on the mechanical properties of base materials and welded joints. The dynamic loading increases the yield stress more than the ultimate tensile strength for the monitored steels, while the most significant increase was recorded for the welded material.

Sign in / Sign up

Export Citation Format

Share Document