scholarly journals Enrichment of lithium from salt lake brine by forward osmosis

2018 ◽  
Vol 5 (10) ◽  
pp. 180965 ◽  
Author(s):  
Jinli Li ◽  
Min Wang ◽  
Youjing Zhao ◽  
Hongjun Yang ◽  
Yuan Zhong
Keyword(s):  
Salt Lake ◽  
Membrane Surface ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Quantitative Structure Activity Relationship ◽  
Contact Angles ◽  
Draw Solution ◽  
Concentrating Solutions ◽  
Relationship Of

Forward osmosis (FO) is a concentration process based on the natural phenomena of osmosis. It is considered a breakthrough technology that can be potentially used for concentrating solutions and suspensions. The diluted nature of brine restricts the treatment technologies that can be applied. Then, brine concentration by FO could represent a new emerging technology enabling the application of a wider range of treatment alternatives. The performance of concentrated brine depending upon FO membranes was studied at normal temperature and pressure in this research. Cellulose triacetates on radio-frequency-weldable non-woven support (CTA-NW) and a thin-film composite with embedded polyester screen support (TFC-ES) were compared; and their orientations were considered. The brine was from Chaerhan Salt Lake after extracting potassium as the feed solution, NaCl solution or MgCl 2 solution as the draw solution. The results indicated that CTA-NW exhibited better concentration performance than TFC-ES, while the water fluxes of the two membranes were exactly the opposite. In the case of CTA-NW in active layer facing feed solution orientation with MgCl 2 as the draw solution, the concentration factor of Li + was nearly 3.0. Quantitative structure–activity relationship of FO membranes and concentration characteristics was correlated, based on results of SEM, FTIR and contact angles studies. The concentration performance could be mainly attributed to the porosity and the thickness of FO membranes; while the water flux was dependent on the hydrophily of FO membrane surface.

scholarly journals Structural investigation and application of Tween 80-choline chloride self-assemblies as osmotic agent for water desalination

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yasamin Bide ◽  
Marzieh Arab Fashapoyeh ◽  
Soheila Shokrollahzadeh
Keyword(s):  
Nonionic Surfactant ◽  
Choline Chloride ◽  
Water Flux ◽  
Forward Osmosis ◽  
Tween 80 ◽  
Average Diameter ◽  
Feed Solution ◽  
Water Desalination ◽  
Draw Solution ◽  
Osmotic Agent

AbstractForward osmosis (FO) process has been extensively considered as a potential technology that could minimize the problems of traditional water desalination processes. Finding an appropriate osmotic agent is an important concern in the FO process. For the first time, a nonionic surfactant-based draw solution was introduced using self-assemblies of Tween 80 and choline chloride. The addition of choline chloride to Tween 80 led to micelles formation with an average diameter of 11.03 nm. The 1H NMR spectra exhibited that all groups of Tween 80 were interacted with choline chloride by hydrogen bond and Van der Waals’ force. The influence of adding choline chloride to Tween 80 and the micellization on its osmotic activity was investigated. Despite the less activity of single components, the average water flux of 14.29 L m‒2 h‒1 was obtained using 0.15 M of Tween 80-choline chloride self-assembly as draw solution in the FO process with DI water feed solution. Moreover, various concentrations of NaCl aqueous solutions were examined as feed solution. This report proposed a possible preparation of nonionic surfactant-based draw solutions using choline chloride additive with enhanced osmotic activities that can establish an innovative field of study in water desalination by the FO process.

scholarly journals Effect of biosurfactant as a novel draw solution on photocatalytic treatment and desalination of produced water by different forward osmosis membranes

2019 ◽  
Vol 20 (1) ◽  
pp. 240-250 ◽  
Author(s):  
Maryam Taghizadeh ◽  
Daryoush Yousefi Kebria ◽  
Farhad Qaderi
Keyword(s):  
Produced Water ◽  
Membrane Surface ◽  
Water Flux ◽  
Forward Osmosis ◽  
Cellulose Triacetate ◽  
Salt Flux ◽  
Draw Solution ◽  
Benzene Toluene ◽  
Reverse Salt Flux ◽  
Contact Angle Analysis

Abstract Water stress and environmental concerns have driven research into the treatment of produced water. In this study, a combination of forward osmosis and photocatalyst system was used for simultaneous salt removal and treatment of produced water. Furthermore, biosurfactant as a novel draw solution and the three types of forward osmosis membranes (cellulose triacetate with and without titanium dioxide (TiO2) and graphene oxide (GO) nanoparticles) were investigated. The morphology and distribution of the TiO2 and TiO2/GO on the membrane surface were assessed by various analyses including field emission scanning electron microscopy, energy dispersive X-ray and contact angle analysis. The results demonstrated that the reverse salt flux was only 0.2 g/m2 h. Moreover, benzene, toluene, ethylbenzene, and xylene (BTEX) removal efficiency in the cellulose triacetate with TiO2 and TiO2/GO membrane under UVC radiation was 62% and 78%, respectively, while the data obtained in visible light reached 80%. The use of TiO2 and TiO2/GO membranes significantly improved the permeability, water flux, photocatalytic degradation of pollutants and desalination of produced water.

scholarly journals Performance of layer-by-layer (LbL) polyelectrolyte forward osmosis membrane for humic acid removal and reverse solute diffusion

2017 ◽  
Vol 19 ◽  
pp. 75 ◽  
Author(s):  
Suriani Husaini ◽  
Mazrul Nizam Abu Seman
Keyword(s):  
Humic Acid ◽  
Chemical Engineering ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Solute Diffusion ◽  
Membrane Properties ◽  
Layer By Layer ◽  
Engineering Research ◽  
Draw Solution

<p>Recent study claimed that forward osmosis (FO) process could handle the fouling problem due it driven force based on natural osmotic pressure. However, researchers observed that FO membrane had problem with reverse solute diffusion (RSD) of draw solution. Therefore, FO membrane properties must be improved either physically or chemically in order to overcome this problem. Among all, surface modification approach has been acknowledged as a best technique to alter the membrane properties without significantly change the bulk membrane properties. In this study, polyelectrolyte FO membrane has been produced through Layer by Layer (LbL) deposition method by using Poly (diallyl-dimethylammoniumchloride), PDADMAC and Poly (sodium 4-styrene-sulfonate), PSS as an active monomers. Humic acid (HA) as part of Natural Organic Matter constituents was used as the feed solution and NaCl as a draw solution. The chemical structure and morphology of the FO membrane were characterized by FTIR and FESEM, respectively. From this study, the highest water flux and humic acid rejection were achieved at 2.5M of draw solution with value of 2.56 L/m<sup>²</sup>.h and 99%, respectively. In general, the water flux increases as the concentration of draw solutions were increased. However, it was observed that reverse salt diffusion (RSD) become worse at higher concentration of draw solution.</p><p>Chemical Engineering Research Bulletin 19(2017) 75-79</p>

scholarly journals Polymer Having Dicationic Structure in Dumbbell Shape for Forward Osmosis Process

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 571 ◽  
Author(s):  
Taehyung Kim ◽  
Changha Ju ◽  
Chanhyuk Park ◽  
Hyo Kang
Keyword(s):  
Aqueous Solutions ◽  
Pure Water ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Solution Temperature ◽  
Solute Flux ◽  
Responsive Polymers ◽  
Draw Solution ◽  
Efficient Recovery

The thermal-responsive polymers, poly(alkane-1,#-diylbis(tri-n-butylphosphonium) 4-vinylbenzenesulfonate) (PSSBP#, # = 8, 6, and 4), where # is the number of carbon atoms in the central bridge structure of the dicationic phosphonium moiety, were synthesized to examine their potential application as draw solutes in forward osmosis (FO). The polymers exhibited low critical solution temperature (LCST) characteristics in aqueous solutions, which is essential for recovering a draw solute from pure water. The LCSTs of the 20 wt% aqueous solutions of PSSBP8, PSSBP6, and PSSBP4 were confirmed to be approximately 30, 38, and 26 °C, respectively, which is advantageous in terms of energy requirements for the recovering draw solute. When the concentration of the PSSBP4 draw solution was 20 wt%, water flux and reverse solute flux were approximately 1.61 LMH and 0.91 gMH, respectively, in the active layer facing the draw solution (AL-DS) system when the feed solution was distilled water. The PSSBP# thermal-responsive draw solute has considerable potential for use as a next-generation draw solute because of its excellent osmotic performance and efficient recovery. Therefore, this study provides inspiration for novel ideas regarding structural transformations of polymers and their applicability as draw solutes.

scholarly journals Investigating the performance of hydroponic nutrient solutions as potential draw solutions for fertilizer drawn forward osmosis

2021 ◽  
Author(s):  
Mohamed Bassiouny ◽  
Peter Nasr ◽  
Hani Sewilam
Keyword(s):  
High Performance ◽  
Low Cost ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Solute Flux ◽  
Water Recovery ◽  
Salt Rejection ◽  
Draw Solution ◽  
Nutrient Solutions

Abstract This research project aims at investigating the performance of hydroponic nutrient solutions as draw solutions for desalination using the fertilizer drawn forward osmosis (FDFO) process. Six different lettuce and leafy greens hydroponic nutrient stock solutions were prepared according to the literature and used in this study and tested on a bench-scale forward osmosis unit as draw solutions for the process. The feed solution for the process was De-Ionized water mixed with NaCl in different concentrations, to represent different salinities of brackish groundwater. The draw efficiency of each solution was measured based on water flux, specific reverse solute flux, water recovery, and salt rejection. It was concluded that of the six tested nutrient solutions, the “Resh Florida, California” solution is the recommended solution to be used as draw solution for fertilizer drawn forward osmosis, due to its high performance in terms of water recovery (15.75%), flux (11 l/m2/h), salt rejection (92%) and SRSF (highest recorded SRSF for a specific ion (SO4 2−) was 7.3 g/l), as well as its low cost, relative to the other highly performing draw solution “Chekli” ($1.07/l vs. $3.73/l).

scholarly journals Forward Osmosis: Temperature Effects By Using Pome as Feed Solution

2015 ◽  
Vol 15 (1) ◽  
pp. 31 ◽  
Author(s):  
Hanizah Arifin ◽  
Thomas S.Y. Choong ◽  
Chan Kam Rong ◽  
Fakhru'l Al-Razi Ahmadun ◽  
Luqman Chuah Abdullah
Keyword(s):  
Water Flux ◽  
Forward Osmosis ◽  
Cross Flow ◽  
Feed Solution ◽  
Water Fluxes ◽  
Energy Applications ◽  
Draw Solution ◽  
Influence Of Temperature On ◽  
Cross Flow Velocity ◽  
Higher Temperature

Forward osmosis (FO) has recently been considered as one of the promising technologies for low energy applications. Factors that influence FO performance are draw solution, types of membrane, membrane orientation, cross flow velocity, module configuration and temperature effect. In this study, the influence of temperature on the performance of FO process has been studied in terms of water flux by using raw POME as feed solution. A higher temperature creates a higher water fluxes at various draw solution concentrations. Percentages of water flux increments for raw POME are between 7% to 9% from 25ºC to 35ºC and 32% to 75% from 25ºC to 45ºC.

A novel positively charged membrane based on polyamide thin-film composite made by cross-linking for nanofiltration

2015 ◽  
Vol 73 (4) ◽  
pp. 776-789 ◽  
Author(s):  
Ahmad Akbari ◽  
Zahra Fakharshakeri ◽  
Sayed Majid Mojallali Rostami
Keyword(s):  
Interfacial Polymerization ◽  
Membrane Surface ◽  
Water Flux ◽  
Feed Solution ◽  
Contact Angles ◽  
Cross Linking ◽  
Cross Sectional ◽  
Charged Membrane ◽  
Trimesoyl Chloride ◽  
Positively Charged

In this paper, a novel positively charged membrane was prepared through interfacial polymerization technique between polyethyleneimine in aqueous phase and trimesoyl chloride in organic phase. Next, cross-linking of polyamide (PA) layer using ρ-xylylene dichloride (XDC) and glutaraldehyde (GA) was studied. The influences of cross-linking concentrations on the separation and permeation performance of membrane were also investigated. Membranes were characterized in terms of their chemical structure, the cross-sectional and surface morphologies, contact angles, molecular weight cut-off (MWCO) and effect of pH feed solution. The salt rejection sequence of CaCl2 &gt;NaCl &gt; Na2SO4 showed a positive charge at the membrane surface after cross-linking reaction. The MWCO of primary PA membrane decreased from 1,135 to 775 and 885 Da for XDC and GA, respectively. XDC membrane shows highest CaCl2 divalent cationic rejection (95.5%) and lowest water flux (21.1 L/m2.h). This study illustrates a promising method for fabrication of positively charged membrane in cation separation.

scholarly journals Evaluation of polyvinylpyrrolidone as draw solute for desalination forward osmosis systems

2021 ◽  
Author(s):  
Quang Trung Nguyen ◽  
Minh Tao Hoang ◽  
Tuan Hung Trinh ◽  
Ngoc Tung Nguyen ◽  
Truong Giang Le
Keyword(s):  
Molecular Weight ◽  
Water Flux ◽  
Forward Osmosis ◽  
Feed Solution ◽  
Raw Material ◽  
Solute Flux ◽  
Initial Concentration ◽  
Draw Solution ◽  
Material Cost ◽  
Solution Parameters

Abstract In this study, polyvinylpyrrolidone (PVP) was evaluated as a potential draw solute for desalination forward osmosis (FO) systems. The effect of various draw solute and draw solution parameters on the efficiency of FO operation was investigated, including PVP molecular weight, PVP concentration in solution, and the salinity of feed solution. Experiment results showed that at draw solution initial concentration of 200 g/L and feed solution initial salinity up to 15 g/L, the PVP-based draw solution can offer water flux up to 14.23 LMH in FO mode with raw material cost only at 0.61 USD/m3. PVP K17 was proven to be an effective draw solute for FO systems, providing good water flux and low reverse draw solute flux; while also being relatively non-toxic, non-corrosive, cheap and widely available compared to other types of novel draw solutes.

scholarly journals Novel draw solutes of iron complexes easier recovery in forward osmosis process

2017 ◽  
Vol 8 (2) ◽  
pp. 244-250 ◽  
Author(s):  
Nguyen Quang Trung ◽  
Le Van Nhan ◽  
Pham Thi Phuong Thao ◽  
Le Truong Giang
Keyword(s):  
Fresh Water ◽  
Salt Water ◽  
Water Flux ◽  
Forward Osmosis ◽  
Iron Complexes ◽  
Feed Solution ◽  
High Water ◽  
Ammonium Bicarbonate ◽  
Draw Solution ◽  
Ammonium Iron

Abstract Forward osmotic (FO) membrane is a new process for producing fresh water from salt water. The study of draw solute is essential in the development and application of FO technology; draw solution should be good at drawing water and easy at recovery. In this paper, three complex draw solutes such as ammonium iron (II) sulfate, ammonium iron (III) sulfate and ammonium iron (III) citrate with different concentrations were studied. The physical properties such as pH, conductivity and total dissolved solids (TDS) have simultaneously been investigated. The pH of most ammonium complexes was decreased whereas TDS increased with increasing of draw solution concentrations. We found that high water flux of these iron complexes was reported in the range of 8.88–11.24 LMH which was higher than the ammonium bicarbonate draw solution. In addition, more than 90% iron complexes draw solutions were recovered by NF-90 membrane, which plays an important role in the FO process to produce fresh water. This study provides direct evidence for the ability of permeate water from feed solution to draw solution, which shows the potential applications of iron complexes in FO process to produce fresh water from sea-, brackish or river water.

scholarly journals ZnO Microfiltration Membranes for Desalination by a Vacuum Flow-Through Evaporation Method

Membranes ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 156 ◽  
Author(s):  
Shailesh Dangwal ◽  
Ruochen Liu ◽  
Lyndon D. Bastatas ◽  
Elena Echeverria ◽  
Chengqian Huang ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Membrane Surface ◽  
Water Flux ◽  
Atomic Layer ◽  
Rejection Rate ◽  
Contact Angles ◽  
Transfer Resistance ◽  
Membrane Pore ◽  
Evaporation Method ◽  
Flow Through

ZnO was deposited on macroporous α-alumina membranes via atomic layer deposition (ALD) to improve water flux by increasing their hydrophilicity and reducing mass transfer resistance through membrane pore channels. The deposition of ZnO was systemically performed for 4–128 cycles of ALD at 170 °C. Analysis of membrane surface by contact angles (CA) measurements revealed that the hydrophilicity of the ZnO ALD membrane was enhanced with increasing the number of ALD cycles. It was observed that a vacuum-assisted ‘flow-through’ evaporation method had significantly higher efficacy in comparison to conventional desalination methods. By using the vacuum-assisted ‘flow-through’ technique, the water flux of the ZnO ALD membrane (~170 L m−2 h−1) was obtained, which is higher than uncoated pristine membranes (92 L m−2 h−1). It was also found that ZnO ALD membranes substantially improved water flux while keeping excellent salt rejection rate (>99.9%). Ultrasonic membrane cleaning had considerable effect on reducing the membrane fouling.

Sign in / Sign up

Export Citation Format

Share Document