Stablen-channel metal-semiconductor field effect transistors on ZnO films deposited using a filtered cathodic vacuum arc

2012 ◽  
Vol 101 (24) ◽  
pp. 243508 ◽  
Author(s):  
S. Elzwawi ◽  
H-S. Kim ◽  
M. Lynam ◽  
E. L. H. Mayes ◽  
D. G. McCulloch ◽  
...  
2003 ◽  
Vol 763 ◽  
Author(s):  
H. W. Lee ◽  
Y. G. Wang ◽  
S. P. Lau ◽  
B. K. Tay

AbstractA detailed study of zinc oxide (ZnO) films prepared by filtered cathodic vacuum arc (FCVA) technique was carried out. To deposit the films, a pure zinc target was used and O2 was fed into the chamber. The electrical properties of both undoped and Al-doped ZnO films were studied. For preparing the Al-doped films, a Zn-Al alloy target with 5 wt % Al was used. The resistivity, Hall mobility and carrier concentration of the samples were measured. The lowest resistivity that can be achieved with undoped ZnO films was 3.4×10-3 Ωcm, and that for Al-doped films was 8×10-4 Ωcm. The carrier concentration was found to increase with Al doping.


Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3423 ◽  
Author(s):  
Junhee Cho ◽  
Seongkwon Hwang ◽  
Doo-Hyun Ko ◽  
Seungjun Chung

Solution-based metal oxide semiconductors (MOSs) have emerged, with their potential for low-cost and low-temperature processability preserving their intrinsic properties of high optical transparency and high carrier mobility. In particular, MOS field-effect transistors (FETs) using the spray pyrolysis technique have drawn huge attention with the electrical performances compatible with those of vacuum-based FETs. However, further intensive investigations are still desirable, associated with the processing optimization and operational instabilities when compared to other methodologies for depositing thin-film semiconductors. Here, we demonstrate high-performing transparent ZnO FETs using the spray pyrolysis technique, exhibiting a field-effect mobility of ~14.7 cm2 V−1 s−1, an on/off ratio of ~109, and an SS of ~0.49 V/decade. We examine the optical and electrical characteristics of the prepared ZnO films formed by spray pyrolysis via various analysis techniques. The influence of spray process conditions was also studied for realizing high quality ZnO films. Furthermore, we measure and analyze time dependence of the threshold voltage (Vth) shifts and their recovery behaviors under prolonged positive and negative gate bias, which were expected to be attributed to defect creation and charge trapping at or near the interface between channel and insulator, respectively.


2019 ◽  
Vol 13 (3) ◽  
pp. 143-149
Author(s):  
Tun Seng Herng ◽  
Shu Ping Lau ◽  
Siu Fung Yu

2003 ◽  
Vol 94 (3) ◽  
pp. 1597-1604 ◽  
Author(s):  
Y. G. Wang ◽  
S. P. Lau ◽  
H. W. Lee ◽  
S. F. Yu ◽  
B. K. Tay ◽  
...  

2021 ◽  
Vol 2 (2) ◽  
pp. 60-71
Author(s):  
John Barron ◽  
Alec Pickett ◽  
James Glaser ◽  
Suchismita Guha

The use of high κ dielectrics lowers the operating voltage in organic field-effect transistors (FETs). Polymer ferroelectrics open the path not just for high κ values but allow processing of the dielectric films via electrical poling. Poled ferroelectric dielectrics in p-type organic FETs was seen to improve carrier mobility and reduce leakage current when compared to unpoled devices using the same dielectric. For n-type FETs, solution-processed ZnO films provide a viable low-cost option. UV–ozone-treated ZnO films was seen to improve the FET performance due to the filling of oxygen vacancies. P-type FETs were fabricated using the ferroelectric polymer poly(vinylidene fluoride-trifluoroethylene) (PVDF-TrFE) as the dielectric along with a donor–acceptor polymer based on diketopyrrolopyrrole (DPP-DTT) as the semiconductor layer. The DPP-DTT FETs yield carrier mobilities upwards of 0.4 cm2/Vs and high on/off ratios when the PVDF-TrFE layer is electrically poled. For n-type FETs, UV–ozone-treated sol–gel ZnO films on SiO2 yield carrier mobilities of 10−2 cm2/Vs. DPP-DTT-based p- and ZnO-based n-type FETs were used in a complementary voltage inverter circuit, showing promising characteristic gain. A basic inverter model was used to simulate the inverter characteristics, using parameters from the individual FET characteristics.


2013 ◽  
Vol 5 (14) ◽  
pp. 6687-6693 ◽  
Author(s):  
Jingjing Chang ◽  
Zhenhua Lin ◽  
Chunxiang Zhu ◽  
Chunyan Chi ◽  
Jie Zhang ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document