Effects of residual stresses on the bending stiffness of shafts strengthened by enveloping de-formation

The aim was to study the effects of technological residual stresses on the bending stiffness of cylindrical parts of shafts and axes. Experiments were conducted for elongated cylindrical specimens made of steel grade 35 with a diameter of 30 mm using boring and turning methods. Specimens were annealed in a protective medium to remove initial residual stresses. Experiments were carried out using an Amsler laboratory hydraulic testing machine and VK8 grade hard-alloy matrices. The experiments showed that, for an extremely low degree of relative crimping of 0.1 to 0.5%, the size of the layer with tangential residual compression stresses gradually decreases. The stiffness of such cylindrical workpieces remains almost unchanged. An increase in relative crimping (from 0.5 to 1.2%) leads to a decrease in resi dual compression stresses on the part surface. The layer thickness with tangential residual compression stresses starts to increase. This leads to a decreased residual buckling and an increased bending stiffness. It was found that the degree of relative crimping has no effect on the variation of distribution depth of axial residual stresses. Optimal distribution of tangential residual compression stresses can be reached by increasing their depth. A linear relationship was found for relative crimping of 0.1 to 1.0%. The highest bending resistance was recorded for specimens strengthened by residual crimping of about 1.0%. By processing workpieces using enveloping deformation with crimping of 0.1% and loading them with a transverse force of 0.6 kN, bending distortion can be decreased and the strength of parts can be increased by 5 times. It was found that the bending stiffness of cylindrical shafts is greatly affected by residual compression stresses. The bedding depth of residual stresses has various effects on the stiffness of cylindrical parts. Thus, correct use of strengthening enveloping deformation can form a high-quality surface layer on parts with the pre-defined distribution of residual stresses.

Shot peening increases resistance to cyclic fatigue fracture of endodontic files

The objective of this study was to assess the resistance to fatigue fracture of conventional nickel–titanium files after undergoing shot peening. Forty NITIFLEX endodontic files, number 30, were divided into two groups; one was submitted to shot peening treatment and the other was not. All instruments were tested for fatigue fracture in simulated canals with a TRI-AUTO ZX endodontic motor. One file of each group was subjected to a residual stress analysis by XRD. Finally, the fractured surface was observed and elemental analysis performed by means of SEM and EDX. Roughness analysis was made by focal variation microscope. The shot peening group showed greater resistance to fatigue fracture; there was no difference in the length of the fractured fragments. XRD results showed the presence of residual compression stresses in the file submitted to shot peening, a decrease in the interplanar spacing, and an increase in the full-width-at-half-maximum and the microstrains. SEM and EDX showed a ductile fracture with zones of fatigue and an equiatomic ratio between the nickel and titanium. Surface roughness increased after the file was subjected to the shot peening procedure. In conclusion, shot peening increases the resistance to fatigue fracture due to the presence of residual compression stresses in files manufactured from a conventional nickel–titanium alloy.

Residual compression property and response of honeycomb sandwich structures subjected to single and repeated quasi-static indentation

This paper investigated the response and residual compression properties of honeycomb sandwich structures subjected to single quasi-static indentation (QSI) and repeated QSI (RQSI). The damage depth after repeated low-velocity impact (LVI) was considered as the governing parameter during the QSI experiments. Three-dimensional digital image correlation method was applied to determine deformation of the front panels after LVI and QSI to describe damage to honeycomb structures. For specimens with the same depth, it is found that the residual strength of QSI was less than that of LVI and close to that of RQSI. Results indicated that it is more reasonable to describe the damage by volume than by depth.

Persisting Complaints after Carpal Tunnel Release: Nerve Compression by the Palmaris Profundus Muscle

We present the case of a 66-year-old man who had persisting complaints after initial classical open carpal tunnel release. During revision a reversed palmaris profundus muscle was identified as being the cause of residual compression of the median nerve. Neurolysis with release of the palmaris profundus muscle was performed without resection of this anatomical variant and resulted in full resolution of the complaints.