Surface roughness contribution to the adhesion force distribution of salmeterol xinafoate on lactose carriers by atomic force microscopy

2005 ◽  
Vol 94 (7) ◽  
pp. 1500-1511 ◽  
Author(s):  
Nazrul Islam ◽  
Peter Stewart ◽  
Ian Larson ◽  
Patrick Hartley
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Adhesion Force ◽  
Force Distribution ◽  
Force Microscopy ◽  
Salmeterol Xinafoate ◽  
Atomic Force

scholarly journals Adhesion force mapping on wood by atomic force microscopy: influence of surface roughness and tip geometry

2016 ◽  
Vol 3 (10) ◽  
pp. 160248 ◽  
Author(s):  
X. Jin ◽  
B. Kasal
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Wood Surface ◽  
Adhesion Force ◽  
Data Interpretation ◽  
Natural Fibre ◽  
Force Distribution ◽  
Adhesion Forces ◽  
Force Microscopy ◽  
Atomic Force

This study attempts to address the interpretation of atomic force microscopy (AFM) adhesion force measurements conducted on the heterogeneous rough surface of wood and natural fibre materials. The influences of wood surface roughness, tip geometry and wear on the adhesion force distribution are examined by cyclic measurements conducted on wood surface under dry inert conditions. It was found that both the variation of tip and surface roughness of wood can widen the distribution of adhesion forces, which are essential for data interpretation. When a common Si AFM tip with nanometre size is used, the influence of tip wear can be significant. Therefore, control experiments should take the sequence of measurements into consideration, e.g. repeated experiments with used tip. In comparison, colloidal tips provide highly reproducible results. Similar average values but different distributions are shown for the adhesion measured on two major components of wood surface (cell wall and lumen). Evidence supports the hypothesis that the difference of the adhesion force distribution on these two locations was mainly induced by their surface roughness.

Brittle Behaviour in Aspirin Crystals: Evidence of Spalling Fracture

2020 ◽  
Author(s):  
Benjamin P. A. Gabriele ◽  
Craig J. Williams ◽  
Douglas Stauffer ◽  
Brian Derby ◽  
Aurora J. Cruz-Cabeza
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Single Crystals ◽  
Spalling Fracture ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Imaging

<div> <div> <div> <p>Single crystals of aspirin form I were cleaved and indented on their dominant face. Upon inspection, it was possible to observe strongly anisotropic shallow lateral cracks due to the extreme low surface roughness after cleavage. Atomic Force Microscopy (AFM) imaging showed spalling fractures nucleating from the indent corners, forming terraces with a height of one or two interplanar spacings d100. The formation of such spalling fractures in aspirin was rationalised using basic calculations of attachment energies, showing how (100) layers are poorly bonded when compared to their relatively higher intralayer bonding. An attempt at explaining the preferential propagation of these fractures along the [010] direction is discussed. </p> </div> </div> </div>

Brittle Behaviour in Aspirin Crystals: Evidence of Spalling Fracture

2020 ◽  
Author(s):  
Benjamin P. A. Gabriele ◽  
Craig J. Williams ◽  
Douglas Stauffer ◽  
Brian Derby ◽  
Aurora J. Cruz-Cabeza
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Single Crystals ◽  
Spalling Fracture ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Imaging

<div> <div> <div> <p>Single crystals of aspirin form I were cleaved and indented on their dominant face. Upon inspection, it was possible to observe strongly anisotropic shallow lateral cracks due to the extreme low surface roughness after cleavage. Atomic Force Microscopy (AFM) imaging showed spalling fractures nucleating from the indent corners, forming terraces with a height of one or two interplanar spacings d100. The formation of such spalling fractures in aspirin was rationalised using basic calculations of attachment energies, showing how (100) layers are poorly bonded when compared to their relatively higher intralayer bonding. An attempt at explaining the preferential propagation of these fractures along the [010] direction is discussed. </p> </div> </div> </div>

scholarly journals Assessing the Functional Properties of TiZr Nanotubular Structures for Biomedical Applications, through Nano-Scratch Tests and Adhesion Force Maps

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 900
Author(s):  
Maria Vardaki ◽  
Aida Pantazi ◽  
Ioana Demetrescu ◽  
Marius Enachescu
Keyword(s):  
Surface Roughness ◽  
Functional Properties ◽  
Bacterial Adhesion ◽  
Biomedical Applications ◽  
Adhesion Force ◽  
Roughness Parameters ◽  
Force Microscopy ◽  
Atomic Force ◽  
The Mean ◽  
Scratch Tests

In this work we present the results of a functional properties assessment via Atomic Force Microscopy (AFM)-based surface morphology, surface roughness, nano-scratch tests and adhesion force maps of TiZr-based nanotubular structures. The nanostructures have been electrochemically prepared in a glycerin + 15 vol.% H2O + 0.2 M NH4F electrolyte. The AFM topography images confirmed the successful preparation of the nanotubular coatings. The Root Mean Square (RMS) and average (Ra) roughness parameters increased after anodizing, while the mean adhesion force value decreased. The prepared nanocoatings exhibited a smaller mean scratch hardness value compared to the un-coated TiZr. However, the mean hardness (H) values of the coatings highlight their potential in having reliable mechanical resistances, which along with the significant increase of the surface roughness parameters, which could help in improving the osseointegration, and also with the important decrease of the mean adhesion force, which could lead to a reduction in bacterial adhesion, are providing the nanostructures with a great potential to be used as a better alternative for Ti implants in dentistry.

scholarly journals Atomic force microscopy comparative analysis of the surface roughness of two posterior chamber phakic intraocular lens models: ICL versus IPCL

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Juan Gros-Otero ◽  
Samira Ketabi ◽  
Rafael Cañones-Zafra ◽  
Montserrat Garcia-Gonzalez ◽  
Cesar Villa-Collar ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Intraocular Lenses ◽  
Posterior Chamber ◽  
Anterior Surface ◽  
Contact Mode ◽  
Force Microscopy ◽  
Atomic Force ◽  
Phakic Intraocular Lenses ◽  
Roughness Measurements

Abstract Background To compare the anterior surface roughness of two commercially available posterior chamber phakic intraocular lenses (IOLs) using atomic force microscopy (AFM). Methods Four phakic IOLs were used for this prospective, experimental study: two Visian ICL EVO+ V5 lenses and two iPCL 2.0 lenses. All of them were brand new, were not previously implanted in humans, were monofocal and had a dioptric power of − 12 diopters (D). The anterior surface roughness was assessed using a JPK NanoWizard II® atomic force microscope in contact mode immersed in liquid. Olympus OMCL-RC800PSA commercial silicon nitride cantilever tips were used. Anterior surface roughness measurements were made in 7 areas of 10 × 10 μm at 512 × 512 point resolution. The roughness was measured using the root-mean-square (RMS) value within the given regions. Results The mean of all anterior surface roughness measurements was 6.09 ± 1.33 nm (nm) in the Visian ICL EVO+ V5 and 3.49 ± 0.41 nm in the iPCL 2.0 (p = 0.001). Conclusion In the current study, we found a statistically significant smoother anterior surface in the iPCL 2.0 phakic intraocular lenses compared with the VISIAN ICL EVO+ V5 lenses when studied with atomic force microscopy.

Copper Diffusion Into Aluminum-Silicon Metallizations by Accelerated Thermal and Electrical Stressing

1996 ◽  
Vol 428 ◽  
Author(s):  
G. O. Ramseyer ◽  
L. H. Walsh ◽  
J. V. Beasock ◽  
H. F. Helbig ◽  
R. C. Lacoe ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Atomic Force Microscopy ◽  
Electron Spectroscopy ◽  
Auger Electron ◽  
Depth Profiling ◽  
Copper Diffusion ◽  
Force Microscopy ◽  
Atomic Force ◽  
Line Widths ◽  
Electromigration Lifetime

AbstractPatterned 930 nm Al(1%-Si) interconnects over 147 nm of Cu were electromigration lifetime tested at 1.0–1.5 × 105 A/cm2 at 250 °C. The morphology of the surfaces of the electromigrated stripes with different line widths and times to failure were characterized by atomic force microscopy, and changes in surface roughness were compared. The diffusion of copper into the electromigrated aluminum stripes was determined by depth profiling using Auger electron spectroscopy. In particular, areas where hillocks formed were examined and compared to areas of median roughness.

Characterization of English ivy (Hedera helix) adhesion force and imaging using atomic force microscopy

2010 ◽  
Vol 13 (3) ◽  
pp. 1029-1037 ◽  
Author(s):  
Lijin Xia ◽  
Scott C. Lenaghan ◽  
Mingjun Zhang ◽  
Yu Wu ◽  
Xiaopeng Zhao ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Adhesion Force ◽  
Hedera Helix ◽  
Force Microscopy ◽  
Atomic Force ◽  
English Ivy
Sign in / Sign up

Export Citation Format

Share Document