Tribochemical Interactions between Carbon Nanotubes and ZDDP Antiwear Additive during Tribofilm Formation on Uncoated and DLC-Coated Steel

The data from the authors’ earlier investigations show that molecules of zinc dithiophosphate (ZDDP) added to a lubricant can absorb energy emitted by a solid surface, which is where triboreactions occur. If the lubricant contains structures able to conduct energy, the ZDDP reactions can occur even at a relatively large distance from the solid surface, which should increase the effectiveness of ZDDP as an antiwear additive. The purpose of this paper was to verify the thesis that the tribocatalytic effect depends on the ability of the solid surface to emit electrons/energy and the ability of ordered molecular structures, such as carbon nanotubes (CNTs), to conduct energy and, most likely, to enhance the energy transfer. The tribological tests were performed using a TRB3 tribotester for 100Cr6 steel balls and uncoated or a-C:H coated HS6-5-2C steel discs. Polyalphaolefin 8 (PAO8) and PAO8 mixed with ZDDP and CNTs were used as lubricants. The results of the tribological tests suggested that: (a) the effect of the interactions between ZDDP and CNTs was clearly visible; (b) the structure and properties of the solid surface layer had a significant influence on the antiwear action of the ZDDP additive.

Mechanical Properties of ZDTP Tribofilms Measured by Nanoindentation: Strain Rate and Temperature Effects

This study aims to contribute to better understand the antiwear action of zinc dialkyldithiophosphate (ZDTP) additives used in car engine lubrication. The antiwear action of ZDTP is associated to the formation of a protective tribofilm onto the rubbing surface. On a mechanical point of view, the efficiency of ZDTP tribofilms results from equilibrium between film formation and wear rates, associated with appropriate rheological properties. In this work, the mechanical properties of a ZDTP tribofilm have been measured by nanoindentation in different test conditions in order to investigate the effect of temperature and strain rate. A Nanoindenter XP® entirely set into a climatic chamber was used to perform the nanoindentation tests. For all tests, an increase of the elastic modulus was observed from a threshold contact pressure value. This effect is similar to the anvil effect observed on polymers: in confined geometry, the elastic modulus increases versus hydrostatic pressure. For the tribofilm, in the studied range, this effect is enhanced at high temperature and low strain rate. Furthermore, when the temperature increases, a change in the rheological behavior of the tribofilm is observed. Up to about 50°C, the tribofilm exhibits viscoplastic behavior — the hardness increases versus strain rate — and above 50°C, the hardness decreases versus strain rate (“shear thinning-like” behavior).

Antiwear and Extreme-Pressure Action of Copper(II) Complex With Alkyl Phosphonic Acid Mono Alkyl Ester

The copper(II) complex with alkylphosphonic acid monoalkyl ester (CuAMP) was synthesized, and its structure shown to be laminar on the basis of fast atom bombardment mass spectroscopy (FABMS). The extreme-pressure, antiwear and antiseizure performance of CuAMP was assessed using a four-ball machine. The results showed that CuAMP exhibits better extreme-pressure and antiwear properties than tricresyl phosphate. Based on the results of surface analysis, the antiwear action mechanism of CuAMP is discussed.

Graphite-like lubrication of mesothelium by oligolamellar pleural surfactant

Six studies have been completed to reevaluate pleural surfactant as a possible boundary lubricant in mesothelial sliding. It is capable of remarkable antiwear action, giving a mean scar diameter on a standard “four-ball test” comparable to the best commercially available lubricants and reducing friction to values anticipated from lamellated solid lubricants such as graphite. Pleural surfaces displayed appreciable hydrophobicity, which was almost eliminated by rinsing with a lipid solvent from which phospholipid was recovered and quantified. These quantities indicated that equivalent of 7.3 adsorbed monolayers of surface-active phospholipid, which was in general agreement with the number of layers of a graphite-like surface coating visualized by electron microscopy by use of a novel fixation procedure that avoids conventional aldehydes known to destroy hydrophobic surfaces. Graphite-like (dry) lubrication by adsorbed surface-active phospholipid is discussed as an excellent lubrication system available wherever the distribution of fluid allows the pleura to make contact.