Improvement of Pitting-Corrosion Resistance of Ultrafine-Grained 7475 Al Alloy by Aging

The effect of aging on the resistance to pitting corrosion of ultrafine-grained 7475 aluminium (Al) alloy processed by hydrostatic extrusion (HE) is studied. Differences in the microstructure were investigated using secondary electron (SEM) and transmission electron microscopy (TEM). Corrosion tests were performed in 0.1 M NaCl, and characterization of corroded surface was performed. The results of this work show that the pitting susceptibility of ultra-fine grained 7475Al is related to the distribution of MgZn2 precipitates. After HE, the formation of An ultrafine-grained microstructure at the grain boundaries of ultrafine grains is observed, while subsequent aging results in the formation of MgZn2 precipitates in the grain interior. Grain refinement increases susceptibility to localized attack, while the subsequent aging improves the overall corrosion resistance and limits the propagation of corrosion attack.

Creep Resistance of S304H Austenitic Steel Processed by High-Pressure Sliding

Sheets of coarse-grained S304H austenitic steel were processed by high-pressure sliding (HPS) at room temperature and a ultrafine-grained microstructure with a mean grain size of about 0.14 µm was prepared. The microstructure changes and creep behavior of coarse-grained and HPS-processed steel were investigated at 500–700 °C under the application of different loads. It was found that the processing of S304H steel led to a significant improvement in creep strength at 500 °C. However, a further increase in creep temperature to 600 °C and 700 °C led to the deterioration of creep behavior of HPS-processed steel. The microstructure results suggest that the creep behavior of HPS-processed steel is associated with the thermal stability of the SPD-processed microstructure. The recrystallization, grain growth, the coarsening of precipitates led to a reduction in creep strength of the HPS-processed state. It was also observed that in the HPS-processed microstructure the fast formation of σ-phase occurs. The σ-phase was already formed during slight grain coarsening at 600 °C and its formation was enhanced after recrystallization at 700 °C.

Ultrafine Cemented Carbides with Cobalt and Iron Binders Prepared via Reactive In Situ Sintering

Reactive sintering of cemented carbides involves mechanical and thermal activation of precursor elemental powders, followed by in-situ synthesis of tungsten carbide. This approach promotes formation of ultrafine microstructure favored in many cemented carbide applications. Our study focuses on the effect of mechanical activation (high-energy milling) on the properties of powder and following thermal activation (sintering) on the microstructure characteristics and phase composition. Reactive sintering proved effective – an ultrafine grained microstructure of cemented carbides with Co and Fe binders was achieved. Formation of tungsten carbide grains was complete at low temperature during reactive spark plasma sintering, resulting in textured microstructure with anisotropic grain formation and growth.

Effect of Chemical Composition on Grain Refinement of AlxCoCrFeNi High Entropy Alloys with NiAl Grain Boundary Precipitates

In AlxCoCrFeNi high entropy alloys (x = 0.3–0.5), the NiAl phase with the B2 structure is precipitated rapidly along the fcc grain boundaries. During recrystallization after conventional cold rolling, the NiAl precipitates effectively suppress the grain growth, which results in the ultrafine-grained microstructure. It should be noted that no severe plastic deformation is necessary to obtain the microstructure. The volume fraction of the NiAl precipitates increases with increasing x. As a result, the average grain size of the fcc matrix (dm) after the recrystallization decreases with increasing x, and therefore, a minimum dm of 0.5 μm can be obtained at x = 0.5. The grain refinement by the NiAl precipitates is consistent with the Zener-Smith model. At x = 0.5, the alloy with dm = 0.5 μm exhibits a yield stress of 1163 MPa and an elongation of 24% at room temperature.

Effect of the uncertainty of multi-cut contour method and friction coefficient on residual stresses of constrained groove pressing process

Constrained groove pressing (CGP) process is a severe plastic deformation (SPD) method that can create ultrafine-grained microstructure in the sheet metals. In this study, residual stresses of the CGP process and the effect of the friction coefficient on the residual stresses were investigated. The residual stresses were measured in two directions using a multi-cut contour method and a mathematical-finite element model was developed to estimate the uncertainty of results of the multi-cut contour method. In order to study the effect of the friction coefficient on the residual stresses, a 3D finite element model was employed and the results of it were validated with the experimental results of the CGP process. According to the results, residual stresses in the first pass of CGP are compressive on the surface and gradually change to tension at the center of the thickness. Investigation of the effect of the first cut on the residual stresses and uncertainty of the second cutting plane showed that the effect of the first cut is only confined to regions near the intersection of the two cuts. Distancing from the intersection of two cuts causes the effect of the first cut to be ineffective on the second cut. Also, evaluation of the effect of friction coefficient on the residual stress illustrated that friction has a direct relationship with the residual stresses.

Microstructural Changes with Annealing of a Nanostructured Al Alloy Severely Plastic Deformed by Four-Layer Stack Accumulative Roll-Bonding Process

Microstructural changes with annealing of a nanostructured complex aluminum alloy fabricated by 3 cycles of four-layer stack ARB process using different Al alloys were investigated in detail. The four-layer stack ARB process using AA1050, AA5052 and AA6061 alloy sheets was performed up to 3 cycles without a lubricant at room temperature. The sample fabricated by the ARB is a multi-layer aluminum alloy sheet in which the AA1050, AA5052 and AA6061 aluminum alloys are alternately stacked to each other. The layer thickness of each alloy became thinner and elongated to the rolling direction with the number of ARB cycles. The grain size decreased with increasing of the number of ARB cycles, and became about 160 nm in thickness after 3 cycles. The complex Al alloy still showed ultrafine grained microstructure to annealing temperature of 300 °C, but it had a heterogeneous structure containing both the ultrafine grains and the coarse grains due to an occurrence of discontinuous recrystallization after 350 °C.

Microstructural and Textural Evolutions of OFHC Cu during the CECC Process and Annealing Treatment

The bulk Cu billets with ultrafine-grained microstructure were successfully processed from full-annealed coarse grained oxygen-free high conductivity (OFHC) Cu by the cyclic extrusion and closed compression (CECC), subsequently annealed at different temperatures. The evolution of the microstructure and mechanical properties was systematically studied. The results show that the effective strain per CECC process is ε=2.77, with further annealing treatment, a high-efficiency grain refinement is realized. After two cycles of CECC process and annealing at 350 °C for 1 h, the grain size refined to ～3 μm, the tensile strength increased to 280 MPa with a high ductility of 54%. Furthermore, a homogeneous structure and mechanical properties in the bulk copper billets for post-forging could be obtained.