Infrared-spectroscopic, dynamic near-field microscopy of living cells and nanoparticles in water

Infrared fingerprint spectra can reveal the chemical nature of materials down to 20-nm detail, far below the diffraction limit, when probed by scattering-type scanning near-field optical microscopy (s-SNOM). But this was impossible with living cells or aqueous processes as in corrosion, due to water-related absorption and tip contamination. Here, we demonstrate infrared s-SNOM of water-suspended objects by probing them through a 10-nm thick SiN membrane. This separator stretches freely over up to 250 µm, providing an upper, stable surface to the scanning tip, while its lower surface is in contact with the liquid and localises adhering objects. We present its proof-of-principle applicability in biology by observing simply drop-casted, living E. coli in nutrient medium, as well as living A549 cancer cells, as they divide, move and develop rich sub-cellular morphology and adhesion patterns, at 150 nm resolution. Their infrared spectra reveal the local abundances of water, proteins, and lipids within a depth of ca. 100 nm below the SiN membrane, as we verify by analysing well-defined, suspended polymer spheres and through model calculations. SiN-membrane based s-SNOM thus establishes a novel tool of live cell nano-imaging that returns structure, dynamics and chemical composition. This method should benefit the nanoscale analysis of any aqueous system, from physics to medicine.

Stamping Nanoparticles onto the Electrode for Rapid Electrochemical Analysis in Microfluidics

Electrochemical analysis is an efficient way to study various materials. However, nanoparticles are challenging due to the difficulty in fabricating a uniform electrode containing nanoparticles. We developed novel approaches to incorporate nanoparticles as a working electrode (WE) in a three-electrode microfluidic electrochemical cell. Specifically, conductive epoxy was used as a medium for direct application of nanoparticles onto the electrode surface. Three approaches in this work were illustrated, including sequence stamping, mix stamping, and droplet stamping. Shadow masking was used to form the conductive structure in the WE surface on a thin silicon nitride (SiN) membrane. Two types of nanomaterials, namely cerium oxide (CeO2) and graphite, were chosen as representative nanoparticles. The as-fabricated electrodes with attached particles were characterized using atomic force microscopy (AFM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Electrochemical analysis was performed to verify the feasibility of these nanoparticles as electrodes. Nanomaterials can be quickly assessed for their electrochemical properties using these new electrode fabrication methods in a microfluidic cell, offering a passport for rapid nanomaterial electrochemical analysis in the future.

Sapphire-Supported Nanopores for Low-Noise DNA Sensing

Silicon-supported (SiS) solid-state nanopores have broad applications in single-molecule biosensing and diagnostics, but their high capacitive noise has seriously limited both their sensing accuracy and recording speed. Nanopores on insulating glass have demonstrated reduced capacitance and noise, but it remains challenging to bulk-etch amorphous glass to create membranes reproducibly and uniformly. Here a new approach is reported to form triangular sapphire-supported (SaS) nanopore membranes by batch-processing-compatible anisotropic wet etching of sapphire, with membrane dimension demonstrated from ~200 μm to 5 μm. A SaS nanopore in 68 μm-wide silicon nitride membrane has 130 times smaller capacitance (10 pF) compared to a SiS nanopore (~4 μm SiN membrane, ~1.3 nF), despite a 100 times larger membrane. It has a current noise of 18 pA over 100 kHz bandwidth, much smaller than that from our SiS nanopore (46 pA) and comparable with the best reported low-noise nanopores. Further, the SaS nanopore displays a higher signal-to-noise ratio (SNR, 21 versus 11 for SiS nanopore) in DNA sensing, although the SNR can be further improved using thinner membranes and smaller pores. The SaS nanopore presents a simple platform in both fabrication and structure that is particularly suitable for low-noise and high-speed molecular diagnostics.

Stable fabrication of a large nanopore by controlled dielectric breakdown in a high-pH solution for the detection of various-sized molecules

For nanopore sensing of various-sized molecules with high sensitivity, the size of the nanopore should be adjusted according to the size of each target molecule. For solid-state nanopores, a simple and inexpensive nanopore fabrication method utilizing dielectric breakdown of a membrane is widely used. This method is suitable for fabricating a small nanopore. However, it suffers two serious problems when attempting to fabricate a large nanopore: the generation of multiple nanopores and the non-opening failure of a nanopore. In this study, we found that nanopore fabrication by dielectric breakdown of a SiN membrane under high-pH conditions (pH ≥ 11.3) could overcome these two problems and enabled the formation of a single large nanopore up to 40 nm in diameter within one minute. Moreover, the ionic-current blockades derived from streptavidin-labelled and non-labelled DNA passing through the fabricated nanopore were clearly distinguished. The current blockades caused by streptavidin-labelled DNA could be identified even when its concentration is 1% of the total DNA.

Microchannel Fabrication Using A Photo-Patternable Adhesive Material for Recording Conformational Changes of KcsA Channel with the Diffracted X-ray Tracking Method

Diffracted X-ray tracking (DXT) method can trace conformational changes of KcsA potassium ion channel during gating by recording position of diffraction spot from a gold nanocrystal attached to the channel as a movie. For high-resolution imaging under controlled microenvironments for KcsA channels, we report a microfluidic device consisting of two SiN membrane windows bonded with a photo patternable adhesive material. The reduced signal-to-background ratio as well as suitable adhesive material thickness for the microchannel are discussed in the experiment at the synchrotron radiation facility.