Wall-Modelled Large Eddy Simulations of Axial Turbine Rim Sealing

This paper presents WMLES simulations of a chute type turbine rim seal. Configurations with an axisymmetric annulus flow and with nozzle guide vanes fitted (but without rotor blades) are considered. The passive scalar concentration solution and WMLES are validated against available data in the literature for uniform convection and a rotor-stator cavity flow. The WMLES approach is shown to be effective, giving significant improvements over an eddy viscosity turbulence model, in prediction of rim seal effectiveness compared to research rig measurements. WMLES requires considerably less computational time than wall-resolved LES, and has the potential for extension to engine conditions. All WMLES solutions show rotating inertial waves in the chute seal. Good agreement between WMLES and measurements for sealing effectiveness in the configuration without vanes is found. For cases with vanes fitted the WMLES simulation shows less ingestion than the measurements, and possible reasons are discussed.

Wall-Modelled Large Eddy Simulations of Axial Turbine Rim Sealing

This paper presents WMLES simulations of a chute type turbine rim seal. Configurations with an axisymmetric annulus flow and with nozzle guide vanes fitted (but without rotor blades) are considered. The passive scalar concentration solution and WMLES are validated against available data in the literature for uniform convection and a rotor-stator cavity flow. The WMLES approach is shown to be effective, giving significant improvements over an eddy viscosity turbulence model, in prediction of rim seal effectiveness compared to research rig measurements. WMLES requires considerably less computational time than wall-resolved LES, and has the potential for extension to engine conditions. All WMLES solutions show rotating inertial waves in the chute seal. Good agreement between WMLES and measurements for sealing effectiveness in the configuration without vanes is found. For cases with vanes fitted the WMLES simulation shows less ingestion than the measurements, and possible reasons are discussed.

Computation of Boiling Water Reactor Annulus Flow Loads Using 2D Potential Flow Methodology and 3D Finite Element Analysis: A Comparative Study

During a Loss of Coolant Accident (LOCA) in a Boiling Water Reactor (BWR), subcooled water flows past jet pump assemblies located in the annular region between the Reactor Pressure Vessel (RPV) and the shroud as it moves toward the break location and is subsequently discharged from the RPV. Flow loads caused by such an event are required design basis loads that must be considered for BWR internal components. A comparison is presented between BWR annulus flow loads calculated by the 2D potential flow methodology using complex variables and the 3D finite element method using the heat transfer analogy described in PVP2016-63091 [1]. The comparison demonstrates that greater solution fidelity is available using the FEA method. The results also demonstrate the importance of applying the appropriate velocity correction factor when flow loads are computed using complex variable techniques.

Effect of Annulus Flow Conditions on Turbine Rim Seal Ingestion

A systematic study of sealing performance for a chute style turbine rim seal using URANS methods is reported. This extends previous studies from a configuration without external flow in the main annulus to cases with a circumferentially uniform axial flow and vane generated swirling annulus flow (but without rotor blades). The study includes variation of the mean seal-to-rotor velocity ratio, main annulus-to-rotor velocity ratio, and seal clearance. The effects on the unsteady flow structures and the degree of main annulus flow ingestion into the rim seal cavity are examined. Sealing effectiveness is quantified by modeling a passive scalar, and the timescales for the convergence of this solution are considered. It has been found that intrinsic flow unsteadiness occurs in most cases, with the presence of vanes and external flow modifying, the associated flow structures and frequencies. Some sensitivities to the annulus flow conditions are identified. The circumferential pressure asymmetry generated by the vanes has a clear influence on the flow structure but does not lead to higher ingestion rates than the other conditions studied.

Re-Ingestion of Upstream Egress in a 1.5-Stage Gas Turbine Rig

In gas turbines, rim seals are fitted at the periphery of stator and rotor discs to minimize the purge flow required to seal the wheel-space between the discs. Ingestion (or ingress) of hot mainstream gases through rim seals is a threat to the operating life and integrity of highly stressed components, particularly in the first-stage turbine. Egress of sealing flow from the first-stage can be re-ingested in downstream stages. This paper presents experimental results using a 1.5-stage test facility designed to investigate ingress into the wheel-spaces upstream and downstream of a rotor disk. Re-ingestion was quantified using measurements of CO2 concentration, with seeding injected into the upstream and downstream sealing flows. Here, a theoretical mixing model has been developed from first principles and validated by the experimental measurements. For the first time, a method to quantify the mass fraction of the fluid carried over from upstream egress into downstream ingress has been presented and measured; it was shown that this fraction increased as the downstream sealing flow rate increased. The upstream purge was shown to not significantly disturb the fluid dynamics but only partially mixes with the annulus flow near the downstream seal, with the ingested fluid emanating from the boundary layer on the blade platform. From the analogy between heat and mass transfer, the measured mass-concentration flux is equivalent to an enthalpy flux, and this re-ingestion could significantly reduce the adverse effect of ingress in the downstream wheel-space. Radial traverses using a concentration probe in and around the rim seal clearances provide insight into the complex interaction between the egress, ingress and mainstream flows.

Experimental Investigation of Turbine Stage Flow Field and Performance at Varying Cavity Purge Rates and Operating Speeds

The aspect of hub cavity purge has been investigated in a high-pressure axial low-reaction turbine stage. The cavity purge is an important part of the secondary air system, used to isolate the cavities below the hub level from the hot main annulus flow. A full-scale cold-flow experimental rig featuring a rotating stage was used in the investigation, quantifying main annulus flow field impact with respect to purge flow rate as it was injected upstream of the rotor. Five operating speeds were investigated of which three with respect to purge flow, namely, a high loading design case, and two high-speed points encompassing the peak efficiency. At each of these operating speeds, the amount of purge flow was varied from 0% to 2%. Observing the effect of the purge rate on measurement plane averaged parameters, a minor flow angle decrease and Mach number increase is seen for the low speed case, while maintaining near constant values for the higher operating speeds. The prominent effect due to purge is seen in the efficiency, showing a linear sensitivity to purge of 1.3%-points for every 1% of added purge flow for the investigated speeds. While spatial average values of flow angle and Mach number are essentially unaffected by purge injection, important spanwise variations are observed and highlighted. The secondary flow structure is strengthened in the hub region, leading to a generally increased over-turning and lowered flow velocity. Meanwhile, the added volume flow through the rotor leads to higher outlet flow velocities visible at higher span, with associated decreased turning. A radial efficiency distribution is utilized, showing negative impact through span heights from 15% to 70%. Pitchwise variation of investigated flow parameters is significantly influenced by purge flow, making this a parameter to include for instance when evaluating benefits of stator clocking positions.