Greenhouse Assays with Lactuca sativa for Testing Sewage Sludge-Based Soil Amendments

Sustainable agriculture practices within the guidelines of nutrient recycling and the circular economy must be increasingly promoted. This work aims to evaluate the performance of dried sewage sludge (DSS), green liquor dregs mixed with sewage sludge (DSSA), raw sewage sludge, and commercial organic fertilizer control, using a short-term agronomic assessment with lettuce crop (Lactuca sativa) in greenhouse conditions. Different application rates based on the nitrogen content were tested for each soil amendment: 0, 85, 170, and 225 kg N/ha (treatments T0, T1, T2, and T3, respectively). DSS and DSSA resulted in fresh lettuce productivities 1.3 and 3.2 times higher in T3 than in T0, respectively. The ideal N content in lettuce leaves was reached for all materials and treatments, with the highest values obtained for DSS (2.88–3.33% from T1 to T3). Lettuce produced in soils amended with DSS and DSSA showed also ideal levels of Ca. Overall, the performance of sludge-based products was similar to commercial fertilizer, without impairing the nutritional balance of the crop and the soil.

Removal of Cr(III) From Water By Polyurethane Foam Incorporated With Green Liquor Dregs Waste

Water bodies contaminated by heavy metals cause a series of severe environmental and health issues. Chromium compounds stand out as one of the main contaminants since they are widely used by several industries. The low efficiency of effluent treatment facilities and the expensive sanitation procedures needed to remove metals from the water lead to serious concerns about the water quality in Brazil. In this study, a rigid polyurethane foam incorporated with green liquor dregs waste was prepared by the free expansion method. The foam composite and its isolated phases were evaluated for removing Cr(III) from water. The isolated dregs removed 81.93% of the Cr(III), which yielded a removal capacity of 135.45 mg·g-1. Whereas, the foam composite displayed Cr(III) removal percentage and capacity of 36.15% and 58.50 mg·g-1, respectively. Results suggests that the hybrid material may be considered for selective removal and extraction of Cr(III) from contaminated water.

Characterisation of Industrial Side Streams and Their Application for the Production of Geopolymer Composites

This study focuses on characterisation of side streams including biomass fly ash, biomass bottom ash, coal fly ash, green liquor dregs, limestone mine tailings, and electric arc furnace steel slag from different industrial locations in Finland. It was found that the fly ash samples contained the highest Al2O3 and SiO2 concentrations, a large number of spherical particles of small sizes and high specific surface areas. Fly ashes and steel slag were observed to contain higher amounts of amorphous phases compared to the other side streams. The high loss on ignition value of the coal fly ash and green liquor dregs was found to exceed the limitations for their application in geopolymer composites. Despite their relatively high concentrations in ashes and steel slag, the leaching tests have shown that no hazardous metal leached out from the streams. Finally, test specimens of geopolymer composites (GP2) were prepared by the application of biomass fly ash, bottom ash, and limestone mine tailings without any pre-treatment process, in addition to the ordinary Portland cement-(R) and metakaolin-based geopolymer composites (GP1). The measured compressive (14.1 MPa) and flexural strength (3.5 MPa) of GP2 suggest that it could be used in concrete kerbs and paving flags. The data has also shown that over 500% of the compressive strength was developed between 7 and 28 days in GP2, whereas in the case of reference concrete (R) and the metakaolin-based geopolymer composite (GP1) it was developed in the first 7 days.

A Review of Technologies Used in Handling The Acid Mine Drainage Challenge: Perspectives on Using Green Liquor Dregs As a Sustainable Option For Treatment of Acid Mine Drainage

Acid mine drainage (AMD) is one of the repercussions that result from earth-moving activities around the sulfide-bearing mineral hosts. The detrimental effects associated with this AMD are driven by its characteristics, which include low pH and high concentrations of sulfate and toxic dissolved metals. Traditionally, the prevention and treatment of AMD are achieved by using technologies that use, amongst other, naturally occurring soils and carbonates. However, the continual use of these materials may eventually lead to their depletion. On the other hand, industrial by-products have been proven to occupying land that could have otherwise been used for profitable businesses. Additionally, the handling and maintenance of landfills are costly. In this current trend of a circular economy that is driven by industrial symbiosis, scientists are concerned with valorizing industrial by-products. One such by-product is the green liquor dregs (GLD) from Kraft mills. The neutralizing and geotechnical properties of these wastes have prompted the research pioneers to seek their potential use in handling the challenges associated with AMD. In this review, the formation AMD, trends in technologies for treatment and prevention of AMD are critically analyzed. This includes the feasibility of using GLD as an alternative, promising sustainable material.

Fate of phosphorus in the recovery cycle of the kraft pulping process

The accumulation of nonprocess elements in the recovery cycle is a common problem for kraft pulp mills trying to reduce their water closure or to utilize biofuels in their lime kiln. Nonprocess elements such as magne-sium (Mg), manganese (Mn), silicon (Si), aluminum (Al), and phosphorus (P) enter the recovery cycle via wood, make-up chemicals, lime rock, biofuels, and process water. The main purge point for these elements is green liquor dregs and lime mud. If not purged, these elements can cause operational problems for the mill. Phosphorus reacts with calcium oxide (CaO) in the lime during slaking; as a result, part of the lime is unavailable for slaking reactions. The first part of this project, through laboratory work, identified rhenanite (NaCa(PO4)) as the form of P in the lime cycle and showed the negative effect of P on the availability of the lime. The second part of this project involved field studies and performing a mass balance for P at a Canadian kraft pulp mill.

Effect of Thermal Drying and Chemical Treatments with Wastes on Microbiological Contamination Indicators in Sewage Sludge

This work aims to evaluate the microbiological contamination of sewage sludge (SS) collected in urban wastewater treatment plants (WWTP) from Portugal. Two types of SS were considered: urban mixed (UM) and from anaerobic digestion (AD). The two types of samples were characterized in relation to the main physical and chemical parameters, as well as the microbiological contamination (Escherichia coli and Salmonella spp). Then, sanitation tests were conducted through thermal drying and chemical treatments. Towards a circular economy, industrial alkaline wastes (green liquor dregs - GLD, lime mud, coal fly ash, eggshell) were tested as alternatives to lime. Only six out of nineteen samples complied with the legal limits for both microorganisms. However, drying at 130 °C sanitized selected samples below the E. coli limit, regardless of the initial moisture or contamination. Additionally, CaO (obtained from eggshell) led to the complete elimination of E. coli at any dosage studied (0.05–0.15 g/g SSwet basis). GLD evidenced the ability to reduce E. coli contamination at room temperature, but not enough to comply with the legal limit. In general, this work highlights the need to sanitize the SS before its application to the soil, and the positive role of some wastes on this goal.