Evaluation of Low-Grade Yellow-Poplar (Liriodendron tulipifera) as Raw Material for Cross-Laminated Timber Panel Production

Utilization of low-grade yellow-poplar (Liriodendron tulipifera) lumber would provide for alternative structural lumber sources and promote the growth of cross-laminated timber (CLT) manufacturing facilities within the Appalachian Region. A significant amount of low-grade yellow-poplar lumber (i.e., National Hardwood Lumber Association [NHLA] No. 2A and Below Grade) is utilized for wood pallets. In practice, this material is not graded for structural purposes. Additionally, research on yellow-poplar for structural use has focused on grading lumber from a small population of selected logs, not by regrading NHLA lumber from manufacturing facilities. Therefore, the research's objective was to investigate the structural grades of a typical population of NHLA graded No. 2 and lower lumber and evaluate their potential to meet structural grades necessary for CLT panels. NHLA graded lumber was regraded and assigned to visual structural grades following Northeastern Lumber Manufacturers Association rules and evaluated for flatwise bending modulus of elasticity (MOEb) by nondestructive proof loading. The results of the study indicated that 54.6 percent of the boards possessed a minimal structural visual grade required for CLT panels according to American National Standards Institutes/The Engineered Wood Association (ANSI/APA) PRG 320-2019 (2020). Splits were the most common limiting defect that downgraded boards to nonstructural grades. Also, 96.6 percent of the boards evaluated had a MOEb above the required minimal board value of 1.2 ×106 psi (8,274 MPa) listed in ANSI/APA PRG 320-2019 (2020). The results of the study indicated that a majority of NHLA low-grade yellow-poplar, when regraded for structural purposes, meets or exceeds minimum lumber grade values necessary for use in CLT panel production.

18 F-FDG-PET/CT assessment of Takayasu arteritis and effect of time-of-flight reconstruction: an observational study

Background To assess the impact of time-of-flight (TOF) positron emission tomography (PET)/computed tomography (CT) image reconstruction on assessment of Takayasu arteritis (TKA). We reviewed 14 patients (15 cases) who underwent TOF-PET/CT. PET images were reconstructed using ordered-subsets expectation maximisation ± TOF. Uptake in 10 vascular regions was assessed using the four-point visual grading system (3, higher than liver uptake; 0, no uptake). The grades in the TOF-PET/CT and non-TOF-PET/CT groups were compared using the sign test. Relationships between visual grade and arterial FDG uptake pattern in the 10 regions and clinical findings were assessed. Results Except for the highest visual grade, the visual grades in all regions were significantly higher in the TOF-PET/CT group (p=0.003). FDG uptake pattern and region were not significant determinants of the effect of TOF reconstruction. Assessment of disease activity was inconsistent between the groups in 6 (4%) of 150 regions when grade 2/3 was defined as active and in 5 (3.3%) of 150 when grade 3 was defined as active. Conclusions Visual grades were significantly higher in all regions when assessed by TOF-PET/CT. Use of the same reconstruction algorithm before and after treatment is recommended when evaluating the response to treatment.

Meningkatkan Kemampuan Menulis Karangan Narasi Melalui Media Visual Siswa Kelas IXE SMP Negeri 25 Kota Jambi Tahun Ajaran 2017/2018

Teaching the writing skills of Bahasa Indonesia to SMP students directed to achieve competencies that can be involved in the ability of students reveal various meanings with the correct steps in the written text of a topic relate to the real experience of daily life – with the emphasis of writing language variations. This research is experimental research; By using a class that is an international class IXE junior high School 25 Jambi city. Based on the ability of the students to write narrative essays by using the visual media acquired spread the value of 77 to 88. The lowest value is 77 and the highest value is 88. So based on the value in the table above can be known the average value of students in writing narrative essays using visual media i.e. the number of scores obtained divided by the number of students (sample) is 2286:28 = 81.64. Thus the result of writing essay based on the word media found in good category with an average value of 81.64. From the two results of the class data of the experiment and the control class, it can be concluded that the ability to write narrative essays using visual media is better than the writing ability of narrative essays by not using media Visual grade IX students E SMP Negeri 25 Jambi City.

Capturing complexity: field-testing the use of ‘structure from motion’ derived virtual models to replicate standard measures of reef physical structure

Reef structural complexity provides important refuge habitat for a range of marine organisms, and is a useful indicator of the health and resilience of reefs as a whole. Marine scientists have recently begun to use ‘Structure from Motion’ (SfM) photogrammetry in order to accurately and repeatably capture the 3D structure of physical objects underwater, including reefs. There has however been limited research on the comparability of this new method with existing analogue methods already used widely for measuring and monitoring 3D structure, such as ‘tape and chain rugosity index (RI)’ and graded visual assessments. Our findings show that analogue and SfM RI can be reliably converted over a standard 10-m reef section (SfM RI = 1.348 × chain RI—0.359, r2 = 0.82; and Chain RI = 0.606 × SfM RI + 0.465) for RI values up to 2.0; however, SfM RI values above this number become increasingly divergent from traditional tape and chain measurements. Additionally, we found SfM RI correlates well with visual assessment grades of coral reefs over a 10 × 10 m area (SfM RI = 0.1461 × visual grade + 1.117; r2 = 0.83). The SfM method is shown to be affordable and non-destructive whilst also allowing the data collected to be archival, less biased by the observer, and broader in its scope of applications than standard methods. This work allows researchers to easily transition from analogue to digital structural assessment techniques, facilitating continued long-term monitoring, whilst also improving the quality and additional research value of the data collected.

Contrast-enhanced Ultrasonography for Monitoring Arterial Inflammation in Takayasu Arteritis

Objective.To evaluate the utility of contrast-enhanced ultrasound (CEUS) compared with 18F-fluorodeoxyglucose–positron emission tomography (FDG-PET) in assessing vessel inflammation of Takayasu arteritis (TA).Methods.This is a retrospective analysis of 71 patients with TA who had undergone carotid CEUS. Twenty-two of 71 patients underwent FDG-PET after CEUS. Clinical disease activity was assessed by Kerr criteria and the Indian Takayasu Clinical Activity Score 2010 (ITAS2010). We investigated the correlation between carotid vascularization on CEUS and clinical data. The consistency of carotid CEUS and PET data has been analyzed for TA disease activity.Results.There was a statistically significant correlation between the results of CEUS and ITAS2010 (p = 0.004) or Kerr criteria (p < 0.001). According to ITAS2010, thirty-four of 71 patients with TA were clinically inactive. Assessment of 34 TA patients with clinically inactive disease yielded 11 CEUS scans that showed active lesions (visual grade ≥ 2) in the left or right carotid artery. In 22 cases that underwent CEUS and FDG-PET, 12 were active and 10 were inactive on the basis of ITAS2010. Moreover, bilateral carotid CEUS vascularization score positively correlated with vascular FDG uptake in these patients with TA (p = 0.004). When vascular inflammation was defined as FDG uptake with visual grade ≥ 2, carotid CEUS showed sensitivity of 100% and specificity of 80%.Conclusion.For TA patients with clinically inactive disease, CEUS could help clinicians to identify active lesions in the carotid vascular region. Carotid CEUS may be a rapid and cost-effective imaging tool in the followup of patients with TA.

Prediction of Douglas-Fir Lumber Properties: Comparison between a Benchtop Near-Infrared Spectrometer and Hyperspectral Imaging System

Near-infrared (NIR) spectroscopy and NIR hyperspectral imaging (NIR-HSI) were compared for the rapid estimation of physical and mechanical properties of No. 2 visual grade 2 × 4 (38.1 mm by 88.9 mm) Douglas-fir structural lumber. In total, 390 lumber samples were acquired from four mills in North America and destructively tested through bending. From each piece of lumber, a 25-mm length block was cut to collect diffuse reflectance NIR spectra and hyperspectral images. Calibrations for the specific gravity (SG) of both the lumber (SGlumber) and 25-mm block (SGblock) and the lumber modulus of elasticity (MOE) and modulus of rupture (MOR) were created using partial least squares (PLS) regression and their performance checked with a prediction set. The strongest calibrations were based on NIR spectra; however, the NIR-HSI data provided stronger predictions for all properties. In terms of fit statistics, SGblock gave the best results, followed by SGlumber, MOE, and MOR. The NIR-HSI SGlumber, MOE, and MOR calibrations were used to predict these properties for each pixel across the transverse surface of the scanned samples, allowing SG, MOE, and MOR variation within and among rings to be observed.

Characterization and Structural Performance in Bending of CLT Panels Made from Small-Diameter Logs of Loblolly/Slash Pine

The main objective of this work was to study the structural viability of using small-diameter logs of Uruguayan Loblolly/Slash pine, mainly from thinning operations, to design cross-laminated timber (CLT) panels. A visual grade named “CTH” (coniferous thinning) was proposed, and 45 specimens of sawn timber boards were tested, resulting in 51% lower bending strength than that of the minimum strength class C14. Subsequently, 20 CLT panels were manufactured and experimentally tested, the results showed that the bending strength of the CLT panels was 43% above that of the individual layers. Additionally, the structural performance of the CLT panels for use in floors was calculated, and the thickness-span relationship depending on strength class and imposed load are presented. Results showed than the use of CTH timber to design CLT floors implies a volume (m3/m2) 17% higher than that using C24 timber.

Validity and reliability of grade scoring in the diagnosis of exercise-induced laryngeal obstruction

The current gold-standard method for diagnosing exercise-induced laryngeal obstruction (EILO) is continuous laryngoscopy during exercise (CLE), with severity classified by a visual grade scoring system. We evaluated the precision of this approach, by evaluating test–retest reliability of CLE and both inter- and intra-rater variability.In this prospective case–control study, subjects completed four consecutive treadmill CLE tests under identical conditions. Laryngoscopic video recordings were anonymised and graded by three expert raters. 2 months following initial scoring, videos were re-randomised and rating repeated to assess intra-rater agreement.20 subjects (16 cases and four controls) completed four CLE tests. The time to exhaustion increased by 30 s (95% CI 0.02–57.8, p<0.05) in the second CLE compared with the first test, but remained identical in the subsequent tests. Only one-third of subjects retained their initial diagnosis in the subsequent three tests. Inter-rater agreement on grade scores (weighted Cohen's ϰ) was 0.16–0.45, while intra-rater agreement ranged from 0.30 to 0.67.The CLE test is key in the diagnostic assessment of patients with EILO. However, the widely adopted visual grade scoring system does not appear to be a robust means for reliably classifying severity of EILO.

Comparison of early and delayed quantified indices of double‐phase 99mtc mibi scintimammography in the detection of primary breast cancer

Purpose: To compare the diagnostic accuracy and incremental diagnostic role of quantitative indices of early and delayed lesion to non‐lesion ratios (L/Ns) in the detection of primary breast cancer. Material and Methods: Double‐phase 99mTc MIBI scintimammography (SMM) (early 10 min, delayed 3 h) was performed after injection of 750 MBq of 99mTc MIBI in 446 highly suspected breast cancer patients (malignant: 311, benign: 135). For visual analysis, five scoring methods were used, and, for quantitative analysis, early and delayed L/Ns were calculated. Receiver operating characteristic curve (ROC) analyses were performed to determine the optimal visual grade, and to calculate cut‐off values of quantitative indices for differentiation of malignant and benign diseases and to investigate whether the quantitative indices could provide incremental diagnostic values in addition to visual analysis. Results: Optimal visual grades were above 4 and 5 in the detection of breast cancer. Sensitivity was 84.2% and specificity 79.3%; the area under the curve (AUC) was 0.832 (95% CI, 0.794–0.866) and standard error was 0.019. Early and delayed L/Ns of malignant breast disease were significantly higher than those of benign disease (early: 2.01±0.99 versus 1.13±0.26 ( P<0.001); delayed: 1.68±0.69 versus 1.11±0.23 ( P<0.001)). The optimal L/Ns for the detection of primary breast cancer were 1.27 for early and 1.12 for delayed imaging. When early L/N 1.27 was used as cut‐off value for the detection of primary breast cancer, the sensitivity of SMM was 77.8% and specificity 85.2%. The AUC was 0.856 (95% CI, 0.820–0.888). When delayed L/N 1.12 was used, sensitivity and specificity were 81.4% and 78.5%, respectively. The AUC was 0.834 (95% CI, 0.796–0.867). The ROC comparison of early and delayed L/N showed no statistical difference in the detection of malignant breast disease ( P = 0.403). When the delayed L/N was added to the early one, early plus delayed quantitative analysis (E+D) showed 86.5% sensitivity and 74.8% specificity. However, the AUCs of E+D (0.854, 95% CI, 0.767–0.842) and early L/N (E) (0.856) showed no statistical difference ( P = 0.614). When grades 4 and 5 were used as cut‐off visual grade, sensitivity and specificity were 84.2% and 79.3%, respectively. When the E was added to visual grade, visual plus early L/N (V+E) showed 89.4% sensitivity and 77% specificity. The AUC of V+E (0.867, 95% CI, 0.832–0.897) was significantly higher than that of visual analysis (V) (0.832, 95% CI, 0.794–0.866, P<0.001). When the delayed L/N (D) was added to visual grade, visual plus delayed L/N (V+D) showed 89.4% sensitivity and 74.1% specificity. The AUCs of V+D (0.852, 95% CI, 0.816–0.884) and V revealed no statistical differences ( P = 0.052). Conclusion: From this study, the optimal visual grades for diagnosis of breast cancer were grades 4 and 5; the cut‐off values of L/Ns were 1.27 for early and 1.12 for delayed imaging. It was also found that early L/Ns provide incremental value in addition to visual analysis. However, delayed L/N revealed no incremental value. Therefore, the delayed image should not be routinely performed for purposes of primary breast cancer detection