scholarly journals The Effect of the Shear Modulus on Planes which is Perpendicular to the Crack’s Edge-planes and Parallel to the Crack’s Front on the ERR in an Orthotropic Rectangular Prism with a Band Crack

2017 ◽  
Vol 17 (1) ◽  
pp. 338-345
Author(s):  
Arzu Turan Dincel
Keyword(s):  
Shear Modulus ◽  
Rectangular Prism ◽  
Band Crack

Effect of Dynamic Crosslinking on Mechanical Properties of PP/EPDM Blends

1993 ◽  
Vol 58 (11) ◽  
pp. 2642-2650 ◽  
Author(s):  
Zdeněk Kruliš ◽  
Ivan Fortelný ◽  
Josef Kovář
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Shear Modulus ◽  
High Impact ◽  
Necessary Condition ◽  
Step Method ◽  
Melt Mixing ◽  
One Step ◽  
High Impact Strength ◽  
Dynamic Curing

The effect of dynamic curing of PP/EPDM blends with sulfur and thiuram disulfide systems on their mechanical properties was studied. The results were interpreted using the knowledge of the formation of phase structure in the blends during their melt mixing. It was shown, that a sufficiently slow curing reaction is necessary if a high impact strength is to be obtained. Only in such case, a fine and homogeneous dispersion of elastomer can be formed, which is the necessary condition for high impact strength of the blend. Using an inhibitor of curing in the system and a one-step method of dynamic curing leads to an increase in impact strength of blends. From the comparison of shear modulus and impact strength values, it follows that, at the stiffness, the dynamically cured blends have higher impact strength than the uncured ones.

Measurement of Young’s Modulus and Shear Modulus of Some Structures Welded Using Flux Cored Wire by Vibration Tests

2014 ◽  
Vol 216 ◽  
pp. 151-156 ◽  
Author(s):  
Liviu Bereteu ◽  
Mircea Vodǎ ◽  
Gheorghe Drăgănescu
Keyword(s):  
Shear Modulus ◽  
Arc Welding ◽  
Natural Frequencies ◽  
Free Vibrations ◽  
Vibration Modes ◽  
Cored Wire ◽  
Flux Cored Arc Welding ◽  
Longitudinal Elastic Modulus ◽  
Vibration Tests ◽  
Non Destructive

The aim of this work was to determine by vibration tests the longitudinal elastic modulus and shear modulus of welded joints by flux cored arc welding. These two material properties are characteristic elastic constants of tensile stress respectively torsion stress and can be determined by several non-destructive methods. One of the latest non-destructive experimental techniques in this field is based on the analysis of the vibratory signal response from the welded sample. An algorithm based on Pronys series method is used for processing the acquired signal due to sample response of free vibrations. By the means of Finite Element Method (FEM), the natural frequencies and modes shapes of the same specimen of carbon steel were determined. These results help to interpret experimental measurements and the vibration modes identification, and Youngs modulus and shear modulus determination.

scholarly journals Evaluation of Dynamic Properties of Sodium-Alginate-Reinforced Soil Using A Resonant-Column Test

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2743
Author(s):  
Seongnoh Ahn ◽  
Jae-Eun Ryou ◽  
Kwangkuk Ahn ◽  
Changho Lee ◽  
Jun-Dae Lee ◽  
...  
Keyword(s):  
Shear Modulus ◽  
Sodium Alginate ◽  
Shear Failure ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Reinforced Soil ◽  
Resonant Column ◽  
Column Test ◽  
Alginate Solution ◽  
Resonant Column Test

Ground reinforcement is a method used to reduce the damage caused by earthquakes. Usually, cement-based reinforcement methods are used because they are inexpensive and show excellent performance. Recently, however, reinforcement methods using eco-friendly materials have been proposed due to environmental issues. In this study, the cement reinforcement method and the biopolymer reinforcement method using sodium alginate were compared. The dynamic properties of the reinforced ground, including shear modulus and damping ratio, were measured through a resonant-column test. Also, the viscosity of sodium alginate solution, which is a non-Newtonian fluid, was also explored and found to increase with concentration. The maximum shear modulus and minimum damping ratio increased, and the linear range of the shear modulus curve decreased, when cement and sodium alginate solution were mixed. Addition of biopolymer showed similar reinforcing effect in a lesser amount of additive compared to the cement-reinforced ground, but the effect decreased above a certain viscosity because the biopolymer solution was not homogeneously distributed. This was examined through a shear-failure-mode test.

scholarly journals Moduli and modes in the Mikado model

Soft Matter ◽  
2021 ◽  
Author(s):  
Brian Tighe ◽  
Karsten Baumgarten
Keyword(s):  
Shear Modulus ◽  
Mechanical Model ◽  
Low Frequency ◽  
Vibrational Modes ◽  
Prior Work ◽  
Fiber Networks ◽  
Elastic Shear Modulus ◽  
Flexible Fiber ◽  
Elastic Shear

We determine how low frequency vibrational modes control the elastic shear modulus of Mikado networks, a minimal mechanical model for semi-flexible fiber networks. From prior work it is known that...

Effects of body postures on the shear modulus of thoracolumbar fascia: a shear wave elastography study

2021 ◽  
Vol 59 (2) ◽  
pp. 383-390
Author(s):  
Baizhen Chen ◽  
Chunlong Liu ◽  
Ming Lin ◽  
Weixin Deng ◽  
Zhijie Zhang
Keyword(s):  
Shear Modulus ◽  
Shear Wave ◽  
Shear Wave Elastography ◽  
Body Postures ◽  
Thoracolumbar Fascia
Sign in / Sign up

Export Citation Format

Share Document