scholarly journals Comparison of Birch and Beech Wood in Terms of Economic and Technological Properties for Plywood Manufacturing

2019 ◽  
Vol 70 (2) ◽  
pp. 169-174
Author(s):  
Evren Osman Cakiroglu ◽  
Aydin Demir ◽  
Ismail Aydin
Keyword(s):  
Betula Pendula ◽  
Bending Strength ◽  
Urea Formaldehyde ◽  
Beech Wood ◽  
Technological Properties ◽  
Annual Increment ◽  
Limit Values ◽  
Plywood Industry ◽  
Fagus Orientalis Lipsky ◽  
Birch Trees

The aim of this study was to investigate the use of birch wood, one of the most important wood species used in the plywood industry, especially in Europe, the Nordic countries, Poland, Belarus and Russia as an alternative to beech wood. For this purpose, comparison was made of their economic and technological properties. In five-ply plywood manufacturing, beech (Fagus orientalis Lipsky) and birch (Betula pendula) veneer sheets were used with melamine urea formaldehyde (MUF) and urea formaldehyde (UF) resins. Some mechanical properties such as shear strength, bending strength and modulus of elasticity of plywood panels were conducted according to EN 314-1 and EN 310, respectively. Mean mechanical strength obtained for birch plywood panels was quite above the limit values specified in the related standards. When taking into consideration the annual increment of beech and birch trees in 1 ha and the time they need to reach suitable diameters for the manufacturing of rotary cut veneers, it was calculated that birch trees provide 2.46 times more physical harvesting than beech trees.

scholarly journals Effect of veneer drying process on some technological properties of polystyrene composite plywood panels

2019 ◽  
Vol 70 (4) ◽  
pp. 369-376
Author(s):  
Hasan Ozturk ◽  
Aydin Demir ◽  
Cenk Demirkir ◽  
Gursel Colakoglu
Keyword(s):  
Bending Strength ◽  
Urea Formaldehyde ◽  
Alnus Glutinosa ◽  
Low Density ◽  
Technological Properties ◽  
Drying Process ◽  
Bonding Material ◽  
Fagus Orientalis Lipsky ◽  
Different Types ◽  
Bonding Shear Strength

The aim of study was to determine the effect of veneer drying process on some technological properties of polystyrene composite plywood panels. For this reason, 2 mm-thick rotary cut veneers were obtained from beech (Fagus orientalis, Lipsky), Alder (Alnus glutinosa subsp. Barbata) and Scots pine (Pinus sylvestris L.) logs. The veneers obtained from three different wood species were divided into two groups to produce polystyrene composite plywood (PCP) and traditional plywood. While PCP was produced both air dried (at 20 °C) and oven dried (at 110 °C), the veneer sheets for production of traditional plywood were dried at 110 °C until reaching 7 % equilibrium moisture content. Two different types of polystyrene with high density (30 kg/m3) and low density (16 kg/m3) were used as bonding material for PCP panel production. The urea-formaldehyde adhesive was used as a bonding material for traditional plywood panels. Bonding shear strength, bending strength, modulus of elasticity and density of plywood and polystyrene composite plywood panels were investigated. It was found that the technological properties observed in the study of composite plywood panels manufactured with natural dried veneers gave similar results compared to those of composites produced with technical dried veneers.

scholarly journals Utilization of Birch Bark as an Eco-Friendly Filler in Urea-Formaldehyde Adhesives for Plywood Manufacturing

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 511
Author(s):  
Roman Réh ◽  
Ľuboš Krišťák ◽  
Ján Sedliačik ◽  
Pavlo Bekhta ◽  
Monika Božiková ◽  
...  
Keyword(s):  
Bending Strength ◽  
Urea Formaldehyde ◽  
Formaldehyde Emission ◽  
Birch Bark ◽  
Gravimetric Analysis ◽  
European Standard ◽  
Scanning Calorimetry ◽  
Wood Processing ◽  
Fagus Sylvatica L ◽  
Positive Effect

The potential of using ground birch (Betula verrucosa Ehrh.) bark as an eco-friendly additive in urea-formaldehyde (UF) adhesives for plywood manufacturing was investigated in this work. Five-ply plywood panels were fabricated in the laboratory from beech (Fagus sylvatica L.) veneers bonded with UF adhesive formulations comprising three addition levels of birch bark (BB) as a filler (10%, 15%, and 20%). Two UF resin formulations filled with 10% and 20% wheat flour (WF) were used as reference samples. The mechanical properties (bending strength, modulus of elasticity and shear strength) of the laboratory-fabricated plywood panels, bonded with the addition of BB in the adhesive mixture, were evaluated and compared with the European standard requirements (EN 310 and EN 314-2). The mechanical strength of the plywood with the addition of BB in the adhesive mixture is acceptable and met the European standard requirements. Markedly, the positive effect of BB in the UF adhesive mixture on the reduction of formaldehyde emission from plywood panels was also confirmed. Initially, the most significant decrease in formaldehyde release (up to 14%) was measured for the plywood sample, produced with 15% BB. After four weeks, the decrease in formaldehyde was estimated up to 51% for the sample manufactured with 20% BB. The performed differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), and derivative thermogravimetry (DTG), also confirmed the findings of the study. As this research demonstrated, BB as a waste or by-product of wood processing industry, can be efficiently utilized as an environmentally friendly, inexpensive alternative to WF as a filler in UF adhesive formulations for plywood manufacturing.

scholarly journals Towards Silviculture Guidelines to Produce Large-Sized Silver Birch (Betula pendula Roth) Logs in Western Europe

Forests ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 599
Author(s):  
Héloïse Dubois ◽  
Hugues Claessens ◽  
Gauthier Ligot
Keyword(s):  
Betula Pendula ◽  
Western Europe ◽  
Forest Health ◽  
Silver Birch ◽  
Growth Potential ◽  
Betula Pendula Roth ◽  
Crown Diameter ◽  
Birch Trees ◽  
Timber Tree ◽  
Northeastern France

Forest health problems arising from climate change, pests and pathogens are a threat to the main timber tree species. As a result, silver birch (Betula pendula Roth) has become a precious asset for meeting oncoming forestry challenges in western Europe. However, silviculture guidelines to produce high-value birch logs in this region are lacking. Producing large-sized birch trunks requires crown release, i.e., removing crown competitors around selected target trees. These interventions are currently seldom carried out or else too late when the growth potential of the trees has already diminished. This study set out to ascertain the diameter at breast height (dbh) that could be reached by crown-released birch, determine dbh-associated crown diameters, and further characterize the gain obtained from early crown release on birch dbh growth. We measured 704 birch trees that had undergone crown release in 38 naturally regenerated pure birch stands in southern Belgium and in northeastern France. We then evaluated the variation in stem and crown diameter, and analyzed increments in response to the earliness of the interventions in three subsamples, also compared with control target birch. We found that trees with a dbh of 50 cm could be grown within 60 years. Based on crown diameter, to produce 40, 50 and 60 cm dbh trunk, the distance required between target birch trees at the end of the rotation was around 8, 10 and 12 m. With no intervention and in ordinary dense birch regenerations, the dbh increment was found to decline once the stand reached age 4–7 years. Starting crown release in stands aged 4–5 years can double the dbh increment of target trees and provide a continual gain that may last up to 20 years. When birch crowns are released after 9–12 years, it may already be too late for them to recover their best growth rate. Our contribution should help complete emerging guidelines in support of birch silviculture development.

scholarly journals Eco-Friendly, High-Density Fiberboards Bonded with Urea-Formaldehyde and Ammonium Lignosulfonate

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 220
Author(s):  
Petar Antov ◽  
Viktor Savov ◽  
Ľuboš Krišťák ◽  
Roman Réh ◽  
George I. Mantanis
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
High Density ◽  
Thickness Swelling ◽  
Formaldehyde Content ◽  
Uf Resin ◽  
Natural Wood ◽  
European Standards

The potential of producing eco-friendly, formaldehyde-free, high-density fiberboard (HDF) panels from hardwood fibers bonded with urea-formaldehyde (UF) resin and a novel ammonium lignosulfonate (ALS) is investigated in this paper. HDF panels were fabricated in the laboratory by applying a very low UF gluing factor (3%) and ALS content varying from 6% to 10% (based on the dry fibers). The physical and mechanical properties of the fiberboards, such as water absorption (WA), thickness swelling (TS), modulus of elasticity (MOE), bending strength (MOR), internal bond strength (IB), as well as formaldehyde content, were determined in accordance with the corresponding European standards. Overall, the HDF panels exhibited very satisfactory physical and mechanical properties, fully complying with the standard requirements of HDF for use in load-bearing applications in humid conditions. Markedly, the formaldehyde content of the laboratory fabricated panels was extremely low, ranging between 0.7–1.0 mg/100 g, which is, in fact, equivalent to the formaldehyde release of natural wood.

scholarly journals Suitability of Hybrid Acacia Wood for Manufacturing Plywood and Particleboard

2012 ◽  
Vol 36 (2) ◽  
pp. 171-176 ◽  
Author(s):  
MM Rahaman ◽  
K Akhter ◽  
D Biswas ◽  
MW Sheikh
Keyword(s):  
Bending Strength ◽  
Unit Area ◽  
Urea Formaldehyde ◽  
Acacia Mangium ◽  
Solid Content ◽  
Timber Species ◽  
Press Temperature ◽  
Natural Crossing ◽  
Press Time ◽  
Academy Of Sciences

Hybrid acacia, produced from natural crossing between two introduced timber species Acacia mangium and A. auriculiformies has been studied for assessing the suitability of plywood and particleboard manufacture. It was found that 1.5 mm thick smooth and figured veneer can be made and dried easily. Three-ply plywood were made using veneer of this species bonded with liquid urea formaldehyde glue of 50% solid content extended with wheat flower and catalyzed (ammonium chloride) with 2% hardener under the specific pressures, viz., 1.05, 1.40 and 1.76 N/mm2 in three replications at 6 minute press time and 120°C press temperature. Dry and wet shear test were conducted on the sample and their shear load at failure per unit area and percentage of wood failure were determined. 1.76 N/mm2 pressure for the manufacture of ply wood is found to be the best. The particleboard was tested for determining the strength and dimensional stability. The bending strength passed the standard specification, tensile strength was found to be low as per Indian standard. DOI: http://dx.doi.org/10.3329/jbas.v36i2.12960 Journal of Bangladesh Academy of Sciences, Vol. 36, No. 2, 171-176, 2012

Albizia richardiana King & Prain as a raw material for ply and particleboard

2015 ◽  
Vol 22 (3) ◽  
pp. 139-141
Author(s):  
Md. Rahaman ◽  
Khurshid Akhter ◽  
S. Hossain ◽  
Md. Islam
Keyword(s):  
Bending Strength ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Solid Content ◽  
Raw Material ◽  
Standard Specification ◽  
Press Temperature ◽  
Albizia Richardiana ◽  
German Standard ◽  
Press Time

Woods of Albizia richardiana has been studied for assessing the suitability for plywood and particleboard manufacture. It was found that 1.5 mm thick smooth and figured veneer can be peeled and dried easily. Three-ply plywood were made using veneer of this species bonded with liquid urea formaldehyde glue of 50% solid content extended with wheat flour and catalyzed (ammonium chloride) with 2% hardener under the three specific pressures, viz,1.05 N/mm2, 1.40 N/mm2, 1.76 N/mm2 in three replications at 6 minute press time and 120°C press temperature. Dry and wet shear test were conducted on the sample and their shear load at failure per unit area and percentage of wood failure were determined. 1.05 N/mm2 pressure for the manufacture of plywood was found to be the best. The physical and mechanical properties of Albizia richardiana wood particleboard were studied. The particleboards were tested for determining the strength and dimensional stability. The tensile strength 0.56N/mm2 passed the British and German standard specification, bending strength (modulus of rupture10.80N/mm2) was found nearest to Indian Standard but low German and British standard specification.

scholarly journals Betula pendula Ssp. distribution and growth in the sub-Carpathian curvature

2021 ◽  
Vol 3 (2) ◽  
pp. 16-22
Author(s):  
Mihai Harpa ◽  
◽  
Lucian Dinca
Keyword(s):  
Betula Pendula ◽  
Stand Structure ◽  
Economic Value ◽  
Wood Products ◽  
Fuel Wood ◽  
Annual Increment ◽  
Ecological Adaptability ◽  
Secondary Species ◽  
Site Type ◽  
Successional Species

Birch ssp. in the sub-Carpathians curvature can be found in composition with beech and other resinous species, unevenly distributed from the mountain peaks at around 1200 m down to 500-600, mainly from high hills to depressions at 600m, rarely seen on plain sites, crossing different geomorphological structures and overall accounting for 3857.1 ha. The main objective of the paper was to analyze the site and stand characteristics of Betula pendula ssp. Roth. in the subCarpathians curvature as followed: stand structure, stand types and stand site types, soils and different metrics, from growth to yields and its connectivity.The ecological adaptability to climate and soil and early fast growth, makes silver birch fulfill the overall requirements as a pioneer species, mostly naturally regenerated. Birch distribution is highly influenced by stand structure having low proportion in compositions, mean height of 15 m at age 50, and a diameter of 20m. Regarding the site, characteristics are more commonly found on fertile soils, corrugated or fragmented site type with a slope of 20-50° and it is distributed as secondary species in stands, averaging 750m in attitude, ranging from 500 to 1200m, 90% being in mixtures with other species with a mean annual increment of approximately 7 m³/year/ha regardless of stand site type. As an early successional species, it serves as a first colonizer but secondary species and quite often as an ecological instrument to improve the soil characteristics, biodiversity and prevent landslides in certain sites, lacking economic value other than fuel wood or other non-wood products.

scholarly journals The Impact of Paraffin-Thermal Modification of Beech Wood on Its Biological, Physical and Mechanical Properties

Forests ◽  
2019 ◽  
Vol 10 (12) ◽  
pp. 1102 ◽  
Author(s):  
Ladislav Reinprecht ◽  
Miroslav Repák
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Beech Wood ◽  
Physical And Mechanical Properties ◽  
Brown Rot ◽  
European Beech ◽  
White Rot ◽  
White Rot Fungus ◽  
Poria Placenta ◽  
The Impact

The European beech (Fagus sylvatica L.) wood was thermally modified in the presence of paraffin at the temperatures of 190 or 210 °C for 1, 2, 3 or 4 h. A significant increase in its resistance to the brown-rot fungus Poria placenta (by 71.4%–98.4%) and the white-rot fungus Trametes versicolor (by 50.1%–99.5%) was observed as a result of all modification modes. However, an increase in the resistance of beech wood surfaces to the mold Aspergillus niger was achieved only under more severe modification regimes taking 4 h at 190 or 210 °C. Water resistance of paraffin-thermally modified beech wood improved—soaking reduced by 30.2%–35.8% and volume swelling by 26.8%–62.9% after 336 h of exposure in water. On the contrary, its mechanical properties worsened—impact bending strength decreased by 17.8%–48.3% and Brinell hardness by 2.4%–63.9%.

Do Birch Trees (Betula pendula) Grow Better if Foraged by Wood Ants?

10.2307/5486 ◽  
1993 ◽  
Vol 62 (1) ◽  
pp. 101 ◽  
Author(s):  
T. Mahdi ◽  
J.B. Whittaker
Keyword(s):  
Betula Pendula ◽  
Wood Ants ◽  
Birch Trees
Sign in / Sign up

Export Citation Format

Share Document