Design and fabrication of MEMS-type compliant overhang flip-chip interconnect for RF applications

2015 ◽  
Vol 2015 (DPC) ◽  
pp. 002082-002094
Author(s):  
Pingye Xu ◽  
Michael C. Hamilton
Keyword(s):  
Solder Ball ◽  
Flip Chip ◽  
Coefficient Of Thermal Expansion ◽  
Organic Substrate ◽  
Process Temperature ◽  
High Yield ◽  
Wafer Level ◽  
Micro Fabrication ◽  
Compliant Interconnect ◽  
Sac Solder

With the increase of I/O density and scaling of interconnects, conventional solder ball interconnects are required to be made smaller. As a result, the reliability of the conventional solder ball flip-chip interconnects worsens. One method to mitigate this issue is by using underfill. However, underfill undermines the reworkability of the solder joints and is challenging to apply when the gap between chip and substrate is small. Another approach to enhance the reliability is to use taller solder ball interconnects, which is however usually more costly. Instead of using conventional solder ball interconnects, compliant interconnects have also been researched in the past few decades to mitigate the reliability issue. The use of compliant structures can compensate for the coefficient of thermal expansion (CTE) mismatch between a Si chip and an organic substrate. In this work, we present the design and fabrication of MEMS-type compliant overhang flip-chip interconnects. The structures are placed at the end of a coplanar waveguide (CPW) as interconnects between CPWs to research their performance at radio frequency (RF). A micro-fabrication process was adopted to build the interconnects. The CPWs are fabricated using conventional e-beam deposition followed by photolithography and then copper electroplating. The compliant overhangs were fabricated on top of a dome of reflowed photoresist on the CPWs to form a curved shape. The reflow and hard bake of the photoresist requires a process temperature of above 220 °C, which is similar to the reflow temperature of a Sn-Ag-Cu (SAC) solder. Therefore we believe our process is compatible with SAC solder processing infrastructures in terms of process temperature. The fabricated structures show high yield and uniformity. Due to the use of a micro-fabrication based process, the structures have the potential to be scaled and be compatible to wafer level packaging. The CPWs were then flip-chip bonded with the compliant interconnect as transitions. The RF performance of the interconnects up to 50 GHz will be presented.

A Heterogeneous Array of Off-Chip Interconnects for Optimum Mechanical and Electrical Performance

2007 ◽  
Vol 129 (4) ◽  
pp. 460-468 ◽  
Author(s):  
Karan Kacker ◽  
Thomas Sokol ◽  
Wansuk Yun ◽  
Madhavan Swaminathan ◽  
Suresh K. Sitaraman
Keyword(s):  
Flip Chip ◽  
Dielectric Material ◽  
Coefficient Of Thermal Expansion ◽  
Semiconductor Industry ◽  
Organic Substrate ◽  
Electrical Performance ◽  
Integrative Approach ◽  
Wafer Level ◽  
Target Values ◽  
Low K

Demand for off-chip bandwidth has continued to increase. It is projected by the Semiconductor Industry Association in their International Technology Roadmap for Semiconductors that by the year 2015, the chip-to-substrate area-array input-output interconnects will require a pitch of 80 μm. Compliant off-chip interconnects show great potential to address these needs. G-Helix is a lithography-based electroplated compliant interconnect that can be fabricated at the wafer level. G-Helix interconnects exhibit excellent compliance in all three orthogonal directions, and can accommodate the coefficient of thermal expansion (CTE) mismatch between the silicon die and the organic substrate without requiring an underfill. Also, these compliant interconnects are less likely to crack or delaminate the low-k dielectric material in current and future integrated circuits. The interconnects are potentially cost effective because they can be fabricated in batch at the wafer level and using conventional wafer fabrication infrastructure. In this paper, we present an integrative approach, which uses interconnects with varying compliance and thus varying electrical performance from the center to the edge of the die. Using such a varying geometry from the center to the edge of the die, the system performance can be tailored by balancing electrical requirements against thermomechanical reliability concerns. The test vehicle design to assess the reliability and electrical performance of the interconnects is also presented. Preliminary fabrication results for the integrative approach are presented and show the viability of the fabrication procedure. The results from reliability experiments of helix interconnects assembled on an organic substrate are also presented. Initial results from the thermal cycling experiments are promising. Results from mechanical characterization experiments are also presented and show that the out-of-plane compliance exceeds target values recommended by industry experts. Finally, through finite element analysis simulations, it is demonstrated that the die stresses induced by the compliant interconnects are an order of magnitude lower than the die stresses in flip chip on board (FCOB) assemblies, and hence the compliant interconnects are not likely to crack or delaminate low-k dielectric material.

Development of Novel Filler Technology for No-Flow and Wafer Level Underfill Materials

2005 ◽  
Vol 127 (2) ◽  
pp. 77-85 ◽  
Author(s):  
Slawomir Rubinsztajn ◽  
Donald Buckley ◽  
John Campbell ◽  
David Esler ◽  
Eric Fiveland ◽  
...  
Keyword(s):  
Cost Reduction ◽  
Flip Chip ◽  
Coefficient Of Thermal Expansion ◽  
Organic Substrate ◽  
Operating Speed ◽  
Wafer Level ◽  
Package Design ◽  
Chip Technology ◽  
Package Size ◽  
Package Reliability

Flip chip technology is one of the fastest growing segments of electronic packaging with growth being driven by the demands such as cost reduction, increase of input/output density, package size reduction and higher operating speed requirements. Unfortunately, flip chip package design has a significant drawback related to the mismatch of coefficient of thermal expansion (CTE) between the silicon die and the organic substrate, which leads to premature failures of the package. Package reliability can be improved by the application of an underfill. In this paper, we report the development of novel underfill materials utilizing nano-filler technology, which provides a previously unobtainable balance of low CTE and good solder joint formation.

Development of High Density RDL Technologies for Panel Level Processing

2019 ◽  
Vol 2019 (DPC) ◽  
pp. 000284-000313
Author(s):  
Lars Böttcher ◽  
S. Karaszkiewicz ◽  
F. Schein ◽  
R. Kahle ◽  
A. Ostmann
Keyword(s):  
Coefficient Of Thermal Expansion ◽  
High Density ◽  
Organic Films ◽  
High Yield ◽  
Wafer Level ◽  
Final Size ◽  
Process Yield ◽  
Cu Pillar ◽  
Thin Organic Films ◽  
Advanced Packaging

Advanced packaging technologies like wafer-level fan-out and 3D System-in-Packages (SIPs) are rapidly penetrating the market of electronic components. A recent trend to reduce cost is the extension of processes to large manufacturing formats, called Panel Level Packaging (PLP). In a consortium of German partners from industry and research advanced technologies for PLP are developed. The project aims for an integrated process flow for SIPs with chips embedded into an organic laminate matrix. At first dies with Cu pillar structures are placed into openings of a laminate frame layer with very low coefficient of thermal expansion (CTE). They are embedded by vacuum lamination of thin organic films, filling the very small gap down to 15 μm between chips and frame. The frame provides alignment marks for a local registration of following processes. The ridged frame limits die shift during embedding and gives a remarkable handling robustness. Developments are initially performed on a 305×256mm2 panel format, aiming for a final size of 610×615 mm2. On the top side of embedded chips, a 20μm dielectric film is applied. The goal is to avoid additional via formation and to realize a direct connection between the Cu pillar of the die and the RDL The RDL formation is based on semi-additive processing. Therefore a Ti or TiW barrier and Cu seed layer is sputtered. Subsequently a 7μm photoresist is applied and exposed by a newly developed Direct Imaging (DI) system. Lines and spaces of 4μm were achieved with high yield. In the following, Cu is simultaneously electroplated for the via contacts and interconnects traces. Finally, the photo resist is stripped and the TiW barrier and Cu seed layers are etched. The goal of the development is to provide a technology for a high-density RDL formation on large panel sizes. The paper will discuss the new developments in detail, e.g. the influence of most significant process parameters, like lithographical resolution, minimum via diameter and the placement and alignment accuracy on overall process yield.

Reliability Assessment and Failure Analysis of G-Helix, a Free-Standing Compliant Off-Chip Interconnect

2009 ◽  
Vol 6 (1) ◽  
pp. 59-65
Author(s):  
Karan Kacker ◽  
Suresh K. Sitaraman
Keyword(s):  
Failure Analysis ◽  
Dielectric Material ◽  
Organic Substrate ◽  
Wafer Level ◽  
Free Standing ◽  
Fine Pitch ◽  
Cross Section Area ◽  
Interconnect Reliability ◽  
Compliant Interconnect ◽  
Low K

Continued miniaturization in the microelectronics industry calls for chip-to-substrate off-chip interconnects that have 100 μm pitch or less for area-array format. Such fine-pitch interconnects will have a shorter standoff height and a smaller cross-section area, and thus could fail through thermo-mechanical fatigue prematurely. Also, as the industry transitions to porous low-K dielectric/Cu interconnect structures, it is important to ensure that the stresses induced by the off-chip interconnects and the package configuration do not crack or delaminate the low-K dielectric material. Compliant free-standing structures used as off-chip interconnects are a potential solution to address these reliability concerns. In our previous work we have proposed G-Helix interconnects, a lithography-based electroplated compliant off-chip interconnect that can be fabricated at the wafer level. In this paper we develop an assembly process for G-Helix interconnects at a 100 μm pitch, identifying the critical factors that impact the assembly yield of such free-standing compliant interconnect. Reliability data are presented for a 20 mm × 20 mm chip with G-Helix interconnects at a 100 μm pitch assembled on an organic substrate and subjected to accelerated thermal cycling. Subsequent failure analysis of the assembly is performed and limited correlation is shown with failure location predicted by finite elements models.

DEVELOPMENT OF AN ULTRA THIN DIE-TO-WAFER FLIP CHIP STACKING PROCESS FOR 2.5D INTEGRATION

2013 ◽  
Vol 2013 (1) ◽  
pp. 000516-000522 ◽  
Author(s):  
G. Parès ◽  
A. Attard ◽  
F. Dosseul ◽  
A. N'Hari ◽  
O. Boillon ◽  
...  
Keyword(s):  
Flip Chip ◽  
Transient Liquid Phase ◽  
High Yield ◽  
Integration Scheme ◽  
Wafer Level ◽  
Release Process ◽  
Process Improvements ◽  
Low Profile ◽  
Stress Release Process ◽  
Tin Silver Copper

3D integration relying on novel vertical interconnection technologies opens the gate to powerful microelectronic systems in ultra-thin packages answering the demand of the mobile market. Among these, die-to-wafer stacking is a key enabling technology for 2.5D as well as for 3D with technological challenges driven by, in one hand, the increase of the die surface and the number of I/Os and, on the other hand, the reduction of the vertical dimensions. In our integration scheme we have achieved flip chip stacking (or Face to Face) of 35 μm ultra-thin dies with low stand-off (< 15 μm) copper micro-bumps and tin-silver-copper solders (SAC). Ultra-thin dies are prepared using dicing before grinding (DBG) technique. After DBG, plasma stress release process is applied to the backside of the singulated chips. Copper μbump technology is challenging with this very low profile stacking since the current flip chip process is no longer adapted to this geometry and that the die flatness tolerance become very critical to obtain a high soldering yield. Process improvements have been achieved on the copper pillar fabrication itself with several metallurgy stack configurations as well as new processes using damascene techniques. Furthermore, innovative technologies have been deployed on the pick and place and collective soldering processes. Intermetallic formation during reflow process is achieved through transient liquid phase (TLP) reaction leading to thorough consumption of the tin layer and to the formation of Cu6Sn5 and Cu3Sn compounds. Capillary underfill is finally successfully applied in the narrow die-to-wafer gap by jetting technique. After optimization, electrical tests show a very high yield close to 100% over a representative number of fully populated wafers. Reliability tests have also been carried out at wafer level exhibiting no significant resistance increase or yield loss over 1000 thermal cycles between −40 and +125°C.

Development of G-Helix Structure as Off-Chip Interconnect

2004 ◽  
Vol 126 (2) ◽  
pp. 237-246 ◽  
Author(s):  
Qi Zhu ◽  
Lunyu Ma ◽  
Suresh K. Sitaraman
Keyword(s):  
Mechanical Performance ◽  
Coefficient Of Thermal Expansion ◽  
Mechanical Analysis ◽  
Organic Substrate ◽  
Electrical Performance ◽  
Wafer Level ◽  
Wafer Level Packaging ◽  
Package Weight ◽  
Mechanical Compliance ◽  
Cte Mismatch

Microsystem packages continue to demand lower cost, higher reliability, better performance and smaller size. Compliant wafer-level interconnects show great potential for next-generation packaging. G-Helix, an electroplated compliant wafer-level chip-to-substrate interconnect can facilitate wafer-level probing as well as wafer-level packaging without the need for an underfill. The fabrication of the G-Helix interconnect is similar to conventional IC fabrication process and is based on electroplating and photolithography. G-Helix interconnect has good mechanical compliance in the three orthogonal directions and can accommodate the differential displacement induced by the coefficient of thermal expansion (CTE) mismatch between the silicon die and the organic substrate. In this paper, we report the wafer-level fabrication of an area-arrayed G-Helix interconnects. The geometry effect on the mechanical compliance and electrical parasitics of G-Helix interconnects have been studied. Thinner and narrower arcuate beams with larger radius and taller post are found to have better mechanical compliance. However, it is also found that structures with excellent mechanical compliance may not have good electrical performance. Therefore, a trade off is needed. Using response surface methodology (RSM), an optimization has been done. Furthermore, reliability of the optimized G-helix interconnects in a silicon-on-organic substrate assembly has been assessed, which includes the package weight and thermo-mechanical analysis. The pitch size effect on the electrical and mechanical performance of G-Helix interconnects has also been studied.

A Lithography-Based Compliant Chip-to-Substrate Wafer-Level Interconnect

2002 ◽  
Author(s):  
Qi Zhu ◽  
Lunyu Ma ◽  
Suresh K. Sitaraman
Keyword(s):  
High Performance ◽  
Coefficient Of Thermal Expansion ◽  
Low Cost ◽  
Optimization Technique ◽  
Cost Effective ◽  
Organic Substrate ◽  
Electrical Performance ◽  
Wafer Level ◽  
Good Reliability ◽  
Mechanical Compliance

As the rapid advances in IC design and fabrication continue to challenge and push the electronic packaging technology, in terms of fine pitch, high performance, low cost, and good reliability, compliant interconnects show great advantages for next-generation packaging. β-fly is designed as a compliant chip-to-substrate interconnect for performing wafer-level probing and for packaging without underfill. β-fly has good compliance in all directions to compensate the coefficient of thermal expansion (CTE) mismatch between the silicon die and an organic substrate. The fabrication of β-fly is similar to standard IC fabrication, and wafer-level packaging makes it cost effective. In this work, self-weight effect and stress distribution under planar displacement loading of β-fly is studied. The effect of geometry parameters on mechanical and electrical performance of β-fly is also studied. β-fly with thinner and narrower arcuate beams with larger radius and taller post is found to have better mechanical compliance. In addition to mechanical compliance, electrical characteristics of β-fly have also been studied in this work. However, it is found that structures with excellent mechanical compliance cannot have good electrical performance. Therefore, a trade off is needed for the design of β-fly. Response surface methodology and an optimization technique have been used to select the optimal β-fly structure parameters.

Wafer-Level, Compliant, Off-Chip Interconnects for Next-Generation Low-K Dielectric/Cu IC’s

2006 ◽  
Author(s):  
Karan Kacker ◽  
George Lo ◽  
Suresh K. Sitaraman
Keyword(s):  
Dielectric Material ◽  
Semiconductor Industry ◽  
Cost Effective ◽  
Organic Substrate ◽  
Integrative Approach ◽  
Wafer Level ◽  
Technology Roadmap ◽  
Cte Mismatch ◽  
Compliant Interconnect ◽  
Low K

Demand for off-chip bandwidth has continued to increase. It is projected by the Semiconductor Industry Association in their International Technology Roadmap for Semiconductors (ITRS) that by the year 2015, the chip-to-substrate area-array input-output interconnects will require a pitch of 70 μm. Compliant off-chip interconnects show great potential to address these needs. G-Helix is a lithography-based electroplated compliant interconnect that can be fabricated at the wafer level. G-Helix interconnects exhibit excellent compliance in all three orthogonal directions, and can accommodate the CTE mismatch between the silicon die and the organic substrate without requiring an underfill. Also, these compliant interconnect are less likely to crack or delaminate the low-K dielectric material in current and future ICs. The interconnects are also potentially cost effective as they can be fabricated using conventional wafer fabrication infrastructure. In this paper we present an integrative approach which uses interconnects with varying compliance and thus varying electrical preformance from the center to the edge of the die. Using such a varying geometry from the center to the edge of the die, the system performance can be tailored by balancing electrical requirements against thermo-mechanical reliability concerns. We also discuss the reliability assessment results of helix interconnects assembled on an organic substrate. Results from mechanical characterization experiments are also presented.

2nd Level Reliability Improvement on WLCSP

2010 ◽  
Vol 2010 (1) ◽  
pp. 000333-000338
Author(s):  
Seungwook Park ◽  
Jupyo Hong ◽  
Changbae Lee ◽  
Sunhee Moon ◽  
Jinsoo Kim ◽  
...  
Keyword(s):  
Solder Ball ◽  
Coefficient Of Thermal Expansion ◽  
Drop Test ◽  
Wafer Level ◽  
Molding Process ◽  
Property Variation ◽  
Chip Scale Package ◽  
Low Modulus ◽  
Market Needs ◽  
Reliability Issue

Recently the package market is demanding the smaller package size and the lower impedance electrical path with a short interconnection. The wafer level chip scale package is one of them, which has the solution of the market needs above. However, WLCSP technology is still not fully accepted on the large device size that is larger than 5mm × 5mm. It needs to overcome 2nd level reliability issue on both solder joint and drop reliability test. To improve 2nd level reliability, we need to apply the longer stand–off design such as Cu –post and double solder ball instead of single solder ball, and low modulus material on polymer layer under the solder pad for releasing thermal stress which result in the solder joints crack due to CTEs (Coefficient of Thermal Expansion) mismatch between organic PCB and WLCSP. In this paper, the double ball structure is introduced as one of them can provide the longer stand off. In addition of improving 2nd level reliability and drop test it may need to apply different solder ball component properties to increase Thermal cycling and drop test. The WLCSP structured a double solder ball showed a better 2nd level reliability result. This paper describes the molding process for double ball process and 2nd level reliability by solder property variation.

Wafer Level Solder Bumping and Flip Chip Assembly with Solder Balls Down to 30μm

2011 ◽  
Vol 2011 (1) ◽  
pp. 000953-000960 ◽  
Author(s):  
Thomas Oppert ◽  
Rainer Dohle ◽  
Jörg Franke ◽  
Stefan Härter
Keyword(s):  
Solder Ball ◽  
Flip Chip ◽  
Temperature Cycling ◽  
Solder Paste ◽  
Wafer Level ◽  
Solder Alloys ◽  
Flip Chips ◽  
Fine Pitch ◽  
Solder Bumps ◽  
Cost Efficient

The most important technology driver in the electronics industry is miniaturization mainly driven by size reduction on wafer level and cost. One of the interconnection technologies for fine pitch applications with the potential for highest integration and cost savings is Flip Chip technology. The commonly used method of generating fine pitch solder bumps is by electroplating the solder. This process is difficult to control or even impossible if it comes to ternary or quaternary alloys. The work described in this study addresses the limitations of existing bumping technologies by enabling low-cost, fine pitch bumping and the use of a very large variety of solder alloys. This flexibility in the selection of the solder materials and UBM stacks is a large advantage if it is essential to improve temperature cycling resistance, drop test resistance, or to increase electromigration lifetime. The technology allows rapid changeover between different low melting solder alloys. Tighter bump pitches and a better bump quality (no flux entrapment) are achievable than with screen printing of solder paste. Because no solder material is wasted, the material costs for precious metal alloys like Au80Sn20 are much lower than with other bumping processes. Solder bumps with a diameter between to date 30 μm and 500 μm as well as small and large batches can be manufactured with one cost efficient process. To explore this potential, cost-efficient solder bumping and automated assembly technologies for the processing of Flip Chips have been developed and qualified. Flip Chips used in this study are 10 mm by 10 mm in size, have a pitch of 100 μm and a solder ball diameter of 30 μm, 40 μm or 50μm, respectively. Wafer level solder application has been done using wafer level solder sphere transfer process or solder sphere jetting technology, respectively. The latter tool has been used for many years in the wafer level packaging industry for both Flip Chip and chip scale packaging applications. It is commonly known in the industry as a solder ball bumping equipment. For the described work the process was scaled down for processing solder spheres with a diameter of 30 μm what was never done before that way worldwide. The research has shown that the underfill process is one of the most crucial factors when it comes to Flip Chip miniaturization for high reliability applications. Therefore, high performance underfill material was qualified initially [1]. Final long term reliability testing has been done according to MIL-STD883G, method 1010.8, condition B up to thirteen thousand cycles with excellent performance of the highly miniaturized solder joints. SEM/EDX and other analysis techniques will be presented. Additionally, an analysis of the failure mechanism will be given and recommendations for key applications and further miniaturization will be outlined.

Sign in / Sign up

Export Citation Format

Share Document