Long-term sulfate attack on recycled aggregate concrete immersed in sodium sulfate solution for 10 years

2020 ◽  
Vol 70 (337) ◽  
pp. 212
Author(s):  
L. R. Santillán ◽  
F. Locati ◽  
Y. A. Villagrán-Zaccardi ◽  
C. J. Zega
Keyword(s):  
Sodium Sulfate ◽  
Fluorescent Microscopy ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Sodium Sulfate Solution ◽  
Microscopy Image

The effect of recycled concrete aggregate (RCA) on concrete performance against external sulfate attack (ESA) is not yet fully known. In this paper, recycled aggregate concretes (RAC) with 0, 50, 75 and 100% of RCA contents were evaluated after 10 years of exposure immersed in 50g/l sodium sulfate solution. Sulfate ingress profiles were obtained by wet chemical analyses and FRX. Also, the mineralogy of the ingress profile was evaluated by thermogravimetric analyses. Finally, microcracking development in samples was evaluated by optical fluorescent microscopy image analysis. Although RAC showed a slight increase in sulfate ingress, due to its higher porosity (about 30% higher SO3 content near the surface for 50% or higher replacement ratio than control concrete), a dense new matrix still allows a good performance of RAC to external sulfate attack with even 100% RCA content.

Recycling of Waste Concrete and Fly Ash for Recycled Aggregate Concrete: Fundamental Characteristics Evaluation

2009 ◽  
Vol 620-622 ◽  
pp. 255-258 ◽  
Author(s):  
Cheol Woo Park
Keyword(s):  
Fly Ash ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Experimental Program ◽  
Concrete Aggregate ◽  
Fine Aggregate ◽  
Recycled Concrete Aggregate ◽  
Aggregate Concrete ◽  
Waste Concrete

As the amount of waste concrete has been increased and recycling technique advances, this study investigates the applicability of recycled concrete aggregate for concrete structures. In addition fly ash, the industrial by-product, was considered in the concrete mix. Experimental program performed compressive strength and chloride penetration resistance tests with various replacement levels of fine recycled concrete aggregate and fly ash. In most case, the design strength, 40MPa, was obtained. It was known that the replacement of the fine aggregate with fine RCA may have greater influence on the strength development rather than the addition of fly ash. It is recommended that when complete coarse aggregate is replaced with RCA the fine RCA replacement should be less than 60%. The recycled aggregate concrete can achieve sufficient resistance to the chloride ion penetration and the resistance can be more effectively controlled by adding fly ash. It I finally conclude that the recycled concrete aggregate can be successfully used in the construction field and the recycling rate of waste concrete and flay ash should be increased without causing significant engineering problems.

X-Ray Microtomography of an Astm C109 Mortar Exposed to Sulfate Attack

1994 ◽  
Vol 370 ◽  
Author(s):  
D.P. Bentz ◽  
Nicos. S. Martys ◽  
P. Stutzman ◽  
M. S. Levenson ◽  
E.J. Garboczi ◽  
...  
Keyword(s):  
Cement Paste ◽  
Sodium Sulfate ◽  
Three Dimensional ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Sodium Sulfate Solution ◽  
Mortar Sample ◽  
Air Voids ◽  
X Ray ◽  
Dimensional Image

AbstractX-ray microtomography can be used to generate three-dimensional 5123 images of random materials at a resolution of a few micrometers per voxel. This technique has been used to obtain an image of an ASTM C109 mortar sample that had been exposed to a sodium sulfate solution. The three-dimensional image clearly shows sand grains, cement paste, air voids, cracks, and needle-like crystals growing in the air voids. Volume fractions of sand and cement paste determined from the image agree well with the known quantities. Implications for the study of microstructure and proposed uses of X-ray microtomography on cement-based composites are discussed.

Analysis of Microstructure of Interfacial Transition Zone (ITZ) in Recycled Aggregate Concrete

2013 ◽  
Vol 811 ◽  
pp. 249-253 ◽  
Author(s):  
Wei Li ◽  
Hai Ying Zhang
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Interfacial Structure ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Interfacial Zone ◽  
Aggregate Concrete ◽  
Mortar Strength

Experiments on influence of species of aggregate and mixing method on interfacial zone in recycled aggregate concrete were investigated. SEM observations revealed that a recycle normal-strength concrete aggregate consist of loose and porous interfacial structure, whereas a recycled high performance concrete (HPC) aggregate and a triple mixing (TM) consist mainly of dense hydrates. Various admixtures on ITZ was produced that consumed CH in the pore, modified attached cement mortar. Strength of recycled concrete was explained by interaction between cements paste and recycled aggregate. The result verified that the relatively dense pore structure of the recycled concrete benefit to development of mechanical properties.

Evaluation of Recycled Aggregate Concrete Cracking through Ring Test

2012 ◽  
Vol 174-177 ◽  
pp. 1475-1480 ◽  
Author(s):  
Valeria Corinaldesi ◽  
Giacomo Moriconi
Keyword(s):  
Numerical Models ◽  
Creep Behaviour ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Tensile Creep ◽  
Ring Test ◽  
Early Age ◽  
Concrete Aggregate ◽  
Free Shrinkage

Cracks can reduce the service life of a concrete structure by allowing aggressive agents to penetrate through it in easy ways. Free shrinkage evaluation alone is not enough to determine if cracking can be expected in a structure since concrete creep behaviour, stiffness and toughness also influence the potential for cracking. Consequently, it is rather interesting to perform restrained shrinkage tests, such as the ring test according to ASTM C 1581–04. The testing procedure involves concrete ring specimens restrained by an inner steel ring on which strain gauges are placed to determine the age of cracking, since abrupt changes in the steel strain occur when concrete is cracked. Both the ring test and free shrinkage test should be carried out in the same exposure conditions, 21°C and 50% relative humidity. Moreover, compressive and tensile strengths of concrete were evaluated on cubic specimens at the time of its cracking and up to 28 days of curing. By means of analytical and numerical models of the ring specimen, some useful information on the stress induced in the material and on the tensile creep behaviour of concrete can be extrapolated thus allowing to better interpret the experimental results. This experimental procedure enables to study the influence of concrete mixture composition on the potential for early-age cracking of concrete. In particular, in this work the influence on early-age cracking of recycled-concrete aggregate partially replacing virgin sand was tested.

scholarly journals A Study Based upon the Usage Recycled Aggregate to Enhance the Strength Aspects of Conventional Concrete: A Critical Review

2021 ◽  
Vol 9 (VI) ◽  
pp. 1567-1570
Author(s):  
Suhail Mushtaq Khan
Keyword(s):  
Chloride Ions ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Concrete Aggregate ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Natural Aggregate ◽  
Concrete Production

Recycled aggregates are those crushed cement concrete or asphalt pavement which comes out from the construction debris which is reused in construction. They are made from the reprocessing of materials which have been used in previous constructions. This paper discusses about the study of properties of recycled aggregates from the sources which has already been published. The results are that 100% replacement of natural aggregate by recycled concrete aggregate effect on chloride ions resistance, it plays negative effects on durability of recycled concrete aggregates, and addition of fiber in recycled aggregate concrete mixture gave more effective in the performance of concrete. On experimental study of recycled aggregate, compressive, flexural and split tensile strength of the recycled aggregate were found to be lower than that of the natural aggregate. Use of recycled aggregate in a new concrete production is still limited. Recommendation of introduction of recycled aggregates standard is required for the materials to be used successfully in future. Gaps in literature reviews are also included in this paper.

scholarly journals Los Angeles index and water absorption capacity of crushed aggregates

2020 ◽  
Vol 15 (1) ◽  
pp. 65-78
Author(s):  
Mohammed Abed ◽  
Rita Nemes
Keyword(s):  
Los Angeles ◽  
Water Absorption ◽  
High Performance Concrete ◽  
Absorption Capacity ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Aggregate Concrete ◽  
Crushed Aggregate

Abstract The mechanical and physical properties of the crushed aggregate have been studied. The properties of crushed aggregate, which produced from recycled aggregate concrete is not discussed in the literature yet despite it could be a choice in some circumstances like in case of demolishing the structures that already constructed by recycled aggregate concrete. Twenty-two types of self-compacting high-performance concrete made by coarse natural aggregate and coarse recycle concrete aggregate have been crushed and their properties have been studied. The main findings of the present study that, the Los Angeles index and water absorption of crushed aggregate is affected by the coarse recycled concrete aggregate dosage in its parent concrete, as well as, incorporating cement replacing materials in parent concrete help to enhance the abrasion resistance of crushed aggregate.

scholarly journals Improved Serviceability and Environmental Performance of One-Way Slabs through the Use of Layered Natural and Recycled Aggregate Concrete

2020 ◽  
Vol 12 (24) ◽  
pp. 10278
Author(s):  
Nikola Tošić ◽  
Snežana Marinković ◽  
Yahya Kurama
Keyword(s):  
Environmental Performance ◽  
Concrete Strength ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Aggregate Concrete ◽  
Reinforced Concrete Slabs ◽  
Service Load ◽  
Better Than

Recycled aggregate concrete (RAC), i.e., concrete produced with recycled concrete aggregate (RCA) has been heavily investigated recently, and the structural design of RAC is entering into design codes. Nonetheless, the service load deflection behavior of RAC remains a challenge due to its larger shrinkage and creep, and lower modulus of elasticity. A novel solution to this challenge is the use of layered concrete, i.e., casting of horizontal layers of different concretes. To investigate the potential benefits and limits of layered concrete, this study contains a numerical parametric assessment of the time-dependent sustained service load deflections and environmental impacts of homogeneous and layered NAC and RAC one-way slabs. Four types of reinforced concrete slabs were considered: homogeneous slabs with 0%, 50% and 100% of coarse RCA (NAC, RAC50 and RAC100, respectively) and layered L-RAC100 slabs with the bottom and top halves consisting of RAC100 and NAC, respectively. In the deflection study, different statical systems, concrete strength classes and relative humidity conditions were investigated. The results showed that the layered L-RAC100 slabs performed as well as, or even better than, the NAC slabs due to the differential shrinkage between the layers. In terms of environmental performance, evaluated using a “cradle-to-gate” Life Cycle Assessment approach, the L-RAC100 slabs also performed as well as, or slightly better than, the NAC slabs. Therefore, layered NAC and RAC slabs can be a potentially advantageous solution from both structural and environmental perspectives.

scholarly journals The influence of recycled concrete aggregate on the properties of concrete

2018 ◽  
Vol 162 ◽  
pp. 02020 ◽  
Author(s):  
Nisreen Mohammed ◽  
Kaiss Sarsam ◽  
Mazin Hussien
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Modulus Of Rupture ◽  
Concrete Aggregate ◽  
Hardened Concrete ◽  
Recycled Coarse Aggregate ◽  
Natural Aggregates

Use of Recycled Coarse Aggregate (RCA) in concrete can be described in terms of environmental protection and economy. This paper deals with the mechanical properties of concrete compressive strength, splitting tensile strength, modulus of elasticity, and modulus of rupture. Three kinds of concrete mixtures were tested, concrete made with Natural Coarse Aggregate (NCA) as a control concrete and two types of concrete made with recycled coarse aggregate (50% and 100% replacement level of coarse recycled aggregate). These kinds of concrete were made with different targets of compressive strength of concrete f ’c (35MPa) and (70 MPa). Fifty specimens were tested of the fresh and hardened properties of concrete. The waste concrete from laboratory test cubes was crushed to produce the Recycled Coarse Aggregate used in recycled concrete. A comparative between the experimental results of the properties for fresh and hardened concrete is presented in the paper. Recycled aggregate concrete (RCA) had a satisfactory performance despite the replacement ratios. It was found using the size of Recycled Coarse Aggregate (RCA) of (5-14) mm has quite similar in performance with the same size of Natural Coarse Aggregate (NCA), it is necessary to use high quality of recycled concrete (with low levels of impurities). Recycled aggregate as an alternative to natural aggregates -seems quite successful.

Resistance to Chloride Penetration of Recycled Aggregate Concrete Modified Using Treated Coarse Recycled Concrete Aggregate and Fibres

2020 ◽  
Vol 991 ◽  
pp. 101-108
Author(s):  
Sallehan Ismail ◽  
Mahyuddin Ramli
Keyword(s):  
Chloride Penetration ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Coupling Effects ◽  
Aggregate Concrete ◽  
Curing Regimes ◽  
Coarse Recycled Concrete Aggregate

This paper presents a study that aimed to assess the chloride penetration depth of recycled aggregate concrete (RAC) modified by using treated coarse recycled concrete aggregate (RCA), adding polyolefin (PO) or polypropylene (PP) fibre and comparing with normal concrete. The coupling effects of the treated RCA and fibres on the chloride penetration of RAC were analysed after two different curing regimes (i.e. normal and seawater) and tested at different curing ages (i.e. 90, 180 and 300 days). Results showed that the inclusion of treated coarse RCA can reduce porosity, thereby decreasing the chloride penetration of RAC. However, the coupling effects of treated coarse RCA and fibre, especially on the use of PO fibre, can enhance the results.

Sign in / Sign up

Export Citation Format

Share Document