Bitumen and bituminous binders. Determination of the fracture toughness temperature by a three point bending test on a notched specimen

2015 ◽  
Keyword(s):  
Fracture Toughness ◽  
Bending Test ◽  
Notched Specimen ◽  
Three Point Bending ◽  
Bituminous Binders

Assessment of Fracture Toughness Using Small Punch Tests of Prenotched Specimens

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Yangyan Zheng ◽  
Xiao Chen ◽  
Zheng Yang ◽  
Xiang Ling
Keyword(s):  
Fracture Toughness ◽  
Numerical Simulations ◽  
Stress Gradient ◽  
Element Model ◽  
Bending Test ◽  
J Integral ◽  
Notched Specimen ◽  
Small Punch ◽  
Three Point Bending ◽  
The Difference

In this paper, line- and ring-notched small punch test (SPT) specimens were studied; a three-dimensional (3D) model of a ring-notched SPT specimen was established using the contour integral method, and the validity of the model was verified using ring-notched specimens. The stress and strain fields were analyzed using numerical simulations of a ring-notched SPT specimen, and the change in the stress gradient during deformation was considered. To verify the finite element model, the results of the numerical simulations were compared with those of three-point bending tests and a Gurson–Tvergaard–Needleman (GTN) model. Compared with the line-notched specimen, the ring-notched specimen was more suitable for notch propagation analysis and fracture toughness evaluation. The results of the numerical simulations were in good agreement with those of the experiments, which showed that the numerical model used in this study was correct. For a notch that initiated when the load reached its maximum value, the value of the J integral was 335 × 10−6 kJ/mm2, and at time 0.85Pmax, the value of the J integral was 201 × 10−6 kJ/mm2, and the difference from the result of the three-point bending test was 14.4%. For a notch that initiated during the stretching deformation stage, the relevant fracture toughness was 225 × 10−6 kJ/mm2, and the difference from the result of the three-point bending test was 3%.

Influence of Al2O3 as Filler Loading on the Fracture Toughness of Light-Cured Dental Resin Composites

2013 ◽  
Vol 816-817 ◽  
pp. 227-231 ◽  
Author(s):  
Saad Omar Alsharif ◽  
Hazizan Md Akil ◽  
Nasser Abbas Abd El-Aziz ◽  
Zainal Arifin Bin Ahmad
Keyword(s):  
Fracture Toughness ◽  
Filler Loading ◽  
Bending Test ◽  
Resin Composites ◽  
Dental Resin ◽  
Notched Specimen ◽  
Three Point Bending ◽  
Dental Resin Composites ◽  
Significant Difference ◽  
Composite Samples

The purpose of the present study was to evaluate the effect of filler loading on the fracture toughness of light-cured dental resin composites (DRCs). The monomer Bis-GMA and TEGDMA (75/25 wt/wt) were mixed with treated micro-sized aluminum oxide (Al2O3) particles ranging from 40-60 wt% as filler. The composite samples were cured with LED for 80s. The bulk density (g/cm3) and apparent porosity (%) of the samples were determined according to the ASTM standard. The fracture toughness (KIC) values of the composites were determined using a single edge notched specimen in the three-point bending test. There was a significant difference in KICof the composites with different loading of Al2O3particles (p< 0.05). The highest amount of filler (60 wt%) reduced the KICvalue to 1.5 MPa.m1/2. As a conclusion, the Al2O3particles used as filler loading does have an effect on the mechanical properties of DRCs.

Mechanical Property and Oxidation Behavior of LPS-SiC Materials

2006 ◽  
Vol 321-323 ◽  
pp. 913-916
Author(s):  
Sang Ll Lee ◽  
Yun Seok Shin ◽  
Jin Kyung Lee ◽  
Jong Baek Lee ◽  
Jun Young Park
Keyword(s):  
Mechanical Property ◽  
Fracture Toughness ◽  
Oxidation Behavior ◽  
Elevated Temperatures ◽  
Indentation Test ◽  
Bending Test ◽  
Secondary Phases ◽  
Three Point Bending ◽  
Different Temperatures

The microstructure and the mechanical property of liquid phase sintered (LPS) SiC materials with oxide secondary phases have been investigated. The strength variation of LPS-SiC materials exposed at the elevated temperatures has been also examined. LPS-SiC materials were sintered at the different temperatures using two types of Al2O3/Y2O3 compositional ratio. The characterization of LPS-SiC materials was investigated by means of SEM with EDS, three point bending test and indentation test. The LPS-SiC material with a density of about 3.2 Mg/m3 represented a flexural strength of about 800 MPa and a fracture toughness of about 9.0 MPa⋅√m.

scholarly journals FDEM Modelling of Rock Fracture Process during Three-Point Bending Test under Quasistatic and Dynamic Loading Conditions

2021 ◽  
Vol 2021 ◽  
pp. 1-21
Author(s):  
Huaming An ◽  
Yushan Song ◽  
Hongyuan Liu
Keyword(s):  
Fracture Toughness ◽  
Dynamic Loading ◽  
Fracture Process ◽  
Loading Rate ◽  
Rock Fracture ◽  
Mesh Size ◽  
Bending Test ◽  
Loading Conditions ◽  
Three Point Bending ◽  
Dynamic Loading Conditions

A hybrid finite-discrete element method (FDEM) is proposed to model rock fracture initiation and propagation during a three-point bending test under quasistatic and dynamic loading conditions. Three fracture models have been implemented in the FDEM to model the transition from continuum to discontinuum through fracture and fragmentation. The loading rate effect on rock behaviour has been taken into account by the implementation of the relationship between the static and dynamic rock strengths derived from dynamic rock fracture experiments. The Brazilian tensile strength test has been modelled to calibrate the FDEM. The FDEM can well model the stress and fracture propagation and well show the stress distribution along the vertical diameter of the disc during the Brazilian tensile strength test. Then, FDEM is implemented to study the rock fracture process during three-point bending tests under quasistatic and dynamic loading conditions. The FDEM has well modelled the stress and fracture propagation and can obtain reasonable fracture toughness. After that, the effects of the loading rate on the rock strength and rock fracture toughness are discussed, and the mesh size and mesh orientation on the fracture patterns are also discussed. It is concluded that the FDEM can well model the rock fracture process by the implementation of the three fracture models. The FDEM can capture the loading rate effect on rock strength and rock fracture toughness. The FDEM is a valuable tool for studying the rock behaviour on the dynamic loading although the proposed method is sensitive to the mesh size and mesh orientation.

Fracture Toughness and Cracking Behaviour of SCC Compared to VC

2013 ◽  
Vol 577-578 ◽  
pp. 205-208
Author(s):  
Sara Korte ◽  
Veerle Boel ◽  
Wouter de Corte ◽  
Geert de Schutter
Keyword(s):  
Fracture Toughness ◽  
Fracture Process ◽  
Critical Value ◽  
Fracture Parameter ◽  
Self Compacting Concrete ◽  
Bending Tests ◽  
Three Point Bending ◽  
Notched Specimens ◽  
Subsequent Determination

Vibrated concrete (VC) and self-compacting concrete (SCC) have a substantially different composition, resulting in dissimilar mechanical properties regarding cracking behaviour. The critical value of the mode I stress-intensity factor KICis an appropriate fracture parameter for evaluating fracture toughness and can be obtained from three-point bending tests (3PBT) on small, notched specimens. Subsequent determination of the energy release rate thus allows to examine the crack propagation and fracture process of both concrete types. This paper describes the results of such 3PBTs on samples, made from VC and SCC. Evaluation of the cracking behaviour, derived from these results, reveals remarkable differences.

scholarly journals Fracture Toughness, Breakthrough Morphology, Microstructural Analysis of the T2 Copper-45 Steel Welded Joints

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 488 ◽  
Author(s):  
Hao Ding ◽  
Qi Huang ◽  
Peng Liu ◽  
Yumei Bao ◽  
Guozhong Chai
Keyword(s):  
Fracture Toughness ◽  
Welded Joints ◽  
Mixed Model ◽  
Experimental Testing ◽  
Microstructural Analysis ◽  
Bending Test ◽  
Dissimilar Welding ◽  
Tensile Fracture ◽  
Three Point Bending ◽  
Welding Materials

The performance and flaws of welded joints are important features that characteristics of the welding material influence. There is significant research activity on the performance and characteristics of welding joint materials. However, the properties of dissimilar welding materials and the cracking problem have not been thoroughly investigated. This investigation focuses on the evaluation and analysis of fracture mechanics, including fracture toughness, microstructural analysis, and crack initiation of T2 copper-45 steel dissimilar welding materials. Standard tensile and three-point bending experiments were performed to calculate the ultimate strength, yield strength, and elastic modulus for fracture toughness. The macro/micro-fracture morphology for tensile fracture and three-point bending fracture were analysed. Based on these investigations, it was concluded that the fracture types were quasi-cleavage and an intergranular brittle fracture mixed model. The deflection of the crack path was discussed and it was determined that the crack was extended along the weld area and tilted towards the T2 copper. Finally, the crack propagation and deflecting direction after the three-point bending test could provide the basis for improvement in the performance of welded joints based on experimental testing parameters and ABAQUS finite element analysis.

Sign in / Sign up

Export Citation Format

Share Document