Assessment of Fracture Toughness Using Small Punch Tests of Prenotched Specimens

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Yangyan Zheng ◽  
Xiao Chen ◽  
Zheng Yang ◽  
Xiang Ling
Keyword(s):  
Fracture Toughness ◽  
Numerical Simulations ◽  
Stress Gradient ◽  
Element Model ◽  
Bending Test ◽  
J Integral ◽  
Notched Specimen ◽  
Small Punch ◽  
Three Point Bending ◽  
The Difference

In this paper, line- and ring-notched small punch test (SPT) specimens were studied; a three-dimensional (3D) model of a ring-notched SPT specimen was established using the contour integral method, and the validity of the model was verified using ring-notched specimens. The stress and strain fields were analyzed using numerical simulations of a ring-notched SPT specimen, and the change in the stress gradient during deformation was considered. To verify the finite element model, the results of the numerical simulations were compared with those of three-point bending tests and a Gurson–Tvergaard–Needleman (GTN) model. Compared with the line-notched specimen, the ring-notched specimen was more suitable for notch propagation analysis and fracture toughness evaluation. The results of the numerical simulations were in good agreement with those of the experiments, which showed that the numerical model used in this study was correct. For a notch that initiated when the load reached its maximum value, the value of the J integral was 335 × 10−6 kJ/mm2, and at time 0.85Pmax, the value of the J integral was 201 × 10−6 kJ/mm2, and the difference from the result of the three-point bending test was 14.4%. For a notch that initiated during the stretching deformation stage, the relevant fracture toughness was 225 × 10−6 kJ/mm2, and the difference from the result of the three-point bending test was 3%.

Influence of Al2O3 as Filler Loading on the Fracture Toughness of Light-Cured Dental Resin Composites

2013 ◽  
Vol 816-817 ◽  
pp. 227-231 ◽  
Author(s):  
Saad Omar Alsharif ◽  
Hazizan Md Akil ◽  
Nasser Abbas Abd El-Aziz ◽  
Zainal Arifin Bin Ahmad
Keyword(s):  
Fracture Toughness ◽  
Filler Loading ◽  
Bending Test ◽  
Resin Composites ◽  
Dental Resin ◽  
Notched Specimen ◽  
Three Point Bending ◽  
Dental Resin Composites ◽  
Significant Difference ◽  
Composite Samples

The purpose of the present study was to evaluate the effect of filler loading on the fracture toughness of light-cured dental resin composites (DRCs). The monomer Bis-GMA and TEGDMA (75/25 wt/wt) were mixed with treated micro-sized aluminum oxide (Al2O3) particles ranging from 40-60 wt% as filler. The composite samples were cured with LED for 80s. The bulk density (g/cm3) and apparent porosity (%) of the samples were determined according to the ASTM standard. The fracture toughness (KIC) values of the composites were determined using a single edge notched specimen in the three-point bending test. There was a significant difference in KICof the composites with different loading of Al2O3particles (p< 0.05). The highest amount of filler (60 wt%) reduced the KICvalue to 1.5 MPa.m1/2. As a conclusion, the Al2O3particles used as filler loading does have an effect on the mechanical properties of DRCs.

Mechanical Property and Oxidation Behavior of LPS-SiC Materials

2006 ◽  
Vol 321-323 ◽  
pp. 913-916
Author(s):  
Sang Ll Lee ◽  
Yun Seok Shin ◽  
Jin Kyung Lee ◽  
Jong Baek Lee ◽  
Jun Young Park
Keyword(s):  
Mechanical Property ◽  
Fracture Toughness ◽  
Oxidation Behavior ◽  
Elevated Temperatures ◽  
Indentation Test ◽  
Bending Test ◽  
Secondary Phases ◽  
Three Point Bending ◽  
Different Temperatures

The microstructure and the mechanical property of liquid phase sintered (LPS) SiC materials with oxide secondary phases have been investigated. The strength variation of LPS-SiC materials exposed at the elevated temperatures has been also examined. LPS-SiC materials were sintered at the different temperatures using two types of Al2O3/Y2O3 compositional ratio. The characterization of LPS-SiC materials was investigated by means of SEM with EDS, three point bending test and indentation test. The LPS-SiC material with a density of about 3.2 Mg/m3 represented a flexural strength of about 800 MPa and a fracture toughness of about 9.0 MPa⋅√m.

scholarly journals FDEM Modelling of Rock Fracture Process during Three-Point Bending Test under Quasistatic and Dynamic Loading Conditions

2021 ◽  
Vol 2021 ◽  
pp. 1-21
Author(s):  
Huaming An ◽  
Yushan Song ◽  
Hongyuan Liu
Keyword(s):  
Fracture Toughness ◽  
Dynamic Loading ◽  
Fracture Process ◽  
Loading Rate ◽  
Rock Fracture ◽  
Mesh Size ◽  
Bending Test ◽  
Loading Conditions ◽  
Three Point Bending ◽  
Dynamic Loading Conditions

A hybrid finite-discrete element method (FDEM) is proposed to model rock fracture initiation and propagation during a three-point bending test under quasistatic and dynamic loading conditions. Three fracture models have been implemented in the FDEM to model the transition from continuum to discontinuum through fracture and fragmentation. The loading rate effect on rock behaviour has been taken into account by the implementation of the relationship between the static and dynamic rock strengths derived from dynamic rock fracture experiments. The Brazilian tensile strength test has been modelled to calibrate the FDEM. The FDEM can well model the stress and fracture propagation and well show the stress distribution along the vertical diameter of the disc during the Brazilian tensile strength test. Then, FDEM is implemented to study the rock fracture process during three-point bending tests under quasistatic and dynamic loading conditions. The FDEM has well modelled the stress and fracture propagation and can obtain reasonable fracture toughness. After that, the effects of the loading rate on the rock strength and rock fracture toughness are discussed, and the mesh size and mesh orientation on the fracture patterns are also discussed. It is concluded that the FDEM can well model the rock fracture process by the implementation of the three fracture models. The FDEM can capture the loading rate effect on rock strength and rock fracture toughness. The FDEM is a valuable tool for studying the rock behaviour on the dynamic loading although the proposed method is sensitive to the mesh size and mesh orientation.

An Experimental Evaluation of Energy Absorption of TRIP Steel by Small Punch Test

2016 ◽  
Vol 725 ◽  
pp. 60-65
Author(s):  
Asuka Hayashi ◽  
Takeshi Iwamoto
Keyword(s):  
Energy Absorption ◽  
Trip Steel ◽  
Dynamic Condition ◽  
High Strength ◽  
High Energy ◽  
Bending Test ◽  
Absorption Characteristic ◽  
Small Punch ◽  
Three Point Bending ◽  
Punch Test

TRIP steel possesses high strength and excellent ductility. In addition, it is possible that TRIP steel indicates high energy absorption so that TRIP steel is expected to apply to automotive members. To design the members made of TRIP steel, it is important to clarify its energy absorption characteristic at various deformation rates. In the previous study, the energy absorption characteristic of TRIP steel is evaluated by J-integral under quasi-static to dynamic condition by using a thick specimen based on ASTM standard. However, by using such thick specimens, it is difficult to conduct the three-point bending test under impact condition because of high ductility in TRIP steel. A small punch (SP) test is the experimental method which can evaluate fracture parameters such as J-integral. By using a conventional use of small specimen in the SP test, it is possible to evaluate J-integral of TRIP steel under impact deformation. In this study, energy absorption characteristic of TRIP steel is investigated by SP test under different deflection rates. Then, the relationship between the values of J-integral obtained by previously conducted three-point bending test and the SP test of TRIP steel is discussed.

Determination of Material Fracture Toughness by Circular Pre-Cracked Small Punch Test Specimens

2019 ◽  
Vol 795 ◽  
pp. 165-171
Author(s):  
Wu Lin Wang ◽  
Du Wei Wang ◽  
Kai Shu Guan
Keyword(s):  
Fracture Toughness ◽  
Empirical Correlation ◽  
Fracture Toughness Test ◽  
J Integral ◽  
Small Punch Test ◽  
Small Punch ◽  
Punch Test ◽  
Determination Procedure ◽  
Material Fracture

Fracture toughness empirical correlation between SPT(Small Punch Test) with non-crack sample and standard fracture toughness test has been established in recent years. In order to compensate the imperfection of empirical correlation, such as absence theoretical basis, poor repeatability and universality, in this paper, an O-type pre-cracked sample was adopted to evaluate fracture toughness. The mechanical model of the sample is in compliance with plane strain condition in the direction of crack propagation. In this paper a determination procedure was studied and established, and the J-integral of steel Q345R was calculated using the procedure.

An Experimental-Numerical Hybrid Method to Determine Dynamic Elastic-Plastic Fracture Toughness

2013 ◽  
Vol 577-578 ◽  
pp. 517-520 ◽  
Author(s):  
Shi Fan Zhu ◽  
Yang Cao ◽  
Chun Huan Guo ◽  
Feng Chun Jiang
Keyword(s):  
Fracture Toughness ◽  
Finite Element ◽  
Dynamic Fracture ◽  
Dynamic Fracture Toughness ◽  
J Integral ◽  
Hopkinson Pressure Bar ◽  
Element Analysis ◽  
Three Point Bending ◽  
Elastic Plastic ◽  
Load Displacement

The dynamic fracture behavior of 7075-T6 aluminum alloy was studied by finite element method to simulate a cracked three-point bending specimen loaded by stress wave loading. In order to determine the elastic-plastic dynamic fracture toughness using quasi-static fracture mechanics theory, the nominal load measured by Hopkinson pressure bar loaded fracture testing system was input into a finite element program to calculate the loading point displacement, and then this displacement was employed to obtain the load-displacement field in the vicinity of the crack tip without the inertia effect, the variation of J-integral as a function of time was established using the load-displacement parameters determined by finite element analysis. The critical J-integral corresponding to crack initiation time detected by a small strain gauge mounted on the three-point bending fracture specimen is determined as an elastic-plastic dynamic fracture toughness (JId). The comparison between the equivalent dynamic fracture toughness(KId) given by the aforementioned procedures and the value measured in previous studies was made to verify the validation of the proposed procedure.

Sign in / Sign up

Export Citation Format

Share Document