scholarly journals Strength, Carbon Footprint and Cost Considerations of Mortar Blends with High Volume Ground Granulated Blast Furnace Slag

2019 ◽  
Vol 11 (24) ◽  
pp. 7194 ◽  
Author(s):  
Chiu Chuen Onn ◽  
Kim Hung Mo ◽  
Mohammed K. H. Radwan ◽  
Wen Hong Liew ◽  
Chee Guan Ng ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Carbon Footprint ◽  
Blast Furnace Slag ◽  
High Volume ◽  
Replacement Level ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Furnace Slag ◽  
Water Binder Ratio

Ground granulated blast furnace slag (GGBFS) is a by-product obtained from the iron making process and has suitable properties to be utilized as high volume cement replacement to produce sustainable concrete. This study focuses on investigating the influence of GGBFS replacement level (0%–70%) and water/binder ratio (0.45 and 0.65) on the performance of cement mortar blends. In order to characterize the engineering performance, the compressive strength of the mortar blends was evaluated. Whereas to ascertain the carbon footprint, environmental life cycle assessment was conducted. Besides the compressive strength and carbon footprint, the materials cost for each mortar blends was computed. Based on the compressive strength/carbon footprint ratio analysis, it was found that increased replacement level of GGBFS gave better performance while the cost efficiency analysis shows that suggested GGBFS replacement level of up to 50%. Overall, in considering the strength performance, carbon footprint and materials cost, the recommended GGBFS replacement level for cement blends is 50%. In addition, when the binder content is kept constant, mortar blends with lower water/binder ratio is preferable when considering the same parameters.

Effect of Ground Granulated Blast Furnace Slag on Compressive Strength of POFA Blended Concrete

2015 ◽  
Vol 802 ◽  
pp. 142-148
Author(s):  
M.N. Noor Azline ◽  
Farah Nora Aznieta Abd Aziz ◽  
Arafa Suleiman Juma
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Strength Development ◽  
Replacement Level ◽  
Concrete Compressive Strength ◽  
Cement Replacement ◽  
Granulated Blast Furnace Slag ◽  
Strength Tests ◽  
Furnace Slag

The article reports a laboratory experimental programme that investigated effect of ground granulated blast furnace (GGBS) on compressive strength of POFA ternary concrete. Compressive strength tests were performed at a range of cements combinations, including 100%PC, two POFA levels for binary concrete, 35% and 45%, and 15%GGBS inclusion for POFA ternary concrete. The compressive strength results were examined in comparison to PC only and equivalent POFA binary concretes for up to 28 days. Results show that the reduction in compressive strength is greater with the higher cement replacement level for all concretes particularly for POFA binary concretes. However, 15%GGBS in POFA blended concrete has a comparable compressive strength compared to PC concrete at both, 35% and 45%, cement replacement levels except for ternary concrete at 0.65 w/c. In addition, the compressive strength of ternary concrete is slightly higher compared to binary concrete for all concrete combinations. Although there is no significant noticeable influence on strength development, the presence of GGBS did not adverse the strength development of POFA blended concrete. Thus, it can be concluded that GGBS compensates the adverse effect of POFA at early strength development.

scholarly journals Early Strength Development of Soft Clay Stabilized by One-Part Ground Granulated Blast Furnace Slag and Fly Ash-Based Geopolymer

2021 ◽  
Vol 8 ◽  
Author(s):  
Xiyao Zheng ◽  
Jun Wu
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Soft Clay ◽  
Strength Development ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Early Strength ◽  
Furnace Slag ◽  
Water Binder Ratio

One-part or “just add water” geopolymer is a cementitious material, which is friendly to environment and users in applications. However, the mechanical behavior of the soft soil stabilized by one-part geopolymer is not well acknowledged. In this study, soft clay was stabilized with ground granulated blast furnace slag (GGBFS) and fly ash (FA)-based geopolymer, which is a mixture of solid aluminosilicate precursor (Al-Si raw materials: GGBFS and FA), solid alkali activator, and water. The objective was to adopt one-part geopolymer as an alternative soil binder to completely replace ordinary Portland cement (OPC) for stabilizing the soft clay and evaluate the effect of the factors (i.e., GBFS/FA ratio in Al-Si precursor, activator/Al-Si precursor ratio, and water/binder ratio) that influenced the early strength. Results showed that the increase of the FA content in the Al-Si precursor increased the unconfined compressive strength (UCS) values significantly through the geopolymerization process. The highest UCS values were achieved with 90% GGBFS to 10% FA in the precursor when the activator/precursor and water/binder ratio is 0.15 and 0.7, respectively. The UCS values of geopolymer-stabilized clay could reach 1.5 MPa at 14 days at ambient temperature, which is much higher than that of OPC-stabilized clay. The microstructure and mineralogy analyses indicated that the prolific hydration products, such as calcium silicate hydrate (C-S-H), calcium aluminum hydrate (C-A-H), and calcium aluminum silicate hydrate (C-A-S-H), contributed greatly to strengthen the soft clay by forming the soil skeleton and infilling among clay particles, while sodium aluminosilicate (N-A-S-H) gel is only served to fill the part of porosities in the soil and cannot effectively enhance the UCS of the one-part geopolymer-stabilized soft clay. This paper results suggested that one-part GGBFS-FA–based geopolymers have the potential to replace OPC in the manufacture of stabilized soft clay.

scholarly journals Blended Cement Containing High Volume Ground Dune Sand and Ground Granulated Blast Furnace Slag for Autoclave Concrete Industry

2015 ◽  
Vol 754-755 ◽  
pp. 395-399 ◽  
Author(s):  
Omer Abdalla Alawad ◽  
Abdulrahman Alhoziamy ◽  
Mohd Saleh Jaafar ◽  
Farah Noor Abdul Aziz ◽  
Abdulaziz Al-Negheimish
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Blended Cement ◽  
High Volume ◽  
Dune Sand ◽  
Significant Drop ◽  
Cement Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents the results of using ground dune sand (GDS) and ground granulated blast furnace slag (slag) as high volume cement replacement materials. In this study, plain and four blended mixtures were fabricated and cured under normal and autoclave conditions. For the blended mixtures, 40% GDS by weight of the total binder materials and different percentages of slag (15%, 30% and 45%) were incorporated as partial cement replacement materials. The effect of curing conditions (normal and autoclave) on the compressive strength of prepared mixtures was studied. The results showed that, for the autoclave cured mixture, up to 85% of cement can be replaced by GDS and slag without significant drop in the compressive strength. Microstructure analyses using scanning electron microscope (SEM) and X-ray diffraction analysis (XRD) were carried out to examine the microscale changes of the hydrated mixtures. The SEM revealed the formation of thin plate-like calcium silicate hydrate and compacted microstructure of autoclave cured mixture. XRD showed the elimination of calcium hydroxide and existence of residual crystalline silica of all blended mixtures.

scholarly journals Effect of Partial Replacement of Ground Granulated Blast Furnace Slag with Sugarcane Bagasse Ash as Source Material in the Production of Geopolymer Concrete

2020 ◽  
Vol 26 (4) ◽  
pp. 477-481
Author(s):  
Parthiban KATHIRVEL ◽  
Murali GUNASEKARAN ◽  
Sreenath SREEKUMARAN ◽  
Arathi KRISHNA
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Sugarcane Bagasse ◽  
Blast Furnace Slag ◽  
Source Material ◽  
Geopolymer Concrete ◽  
Replacement Level ◽  
Granulated Blast Furnace Slag ◽  
Sugarcane Bagasse Ash ◽  
Furnace Slag

The study on the characteristics of geopolymer concrete (GPC) is of ultimate significance to instill assurance in builders and engineers. Abundant available literatures point towards the utilization of fly ash and ground granulated blast furnace slag (GGBFS) as source material in the production of GPC with little on other materials. India produces nearly 350 MMT of sugarcane for the production of sugar, which lies second only to Brazil in the annual production, the disposal of the bagasse creates an environmental issue needs to be effectively utilized. Hence, this work was intended to investigate the effect of utilizing sugarcane bagasse ash (SCBA) as a source material in the production of geopolymer mixes. The fresh (consistency, setting time, soundness and flow), hardened (density, compressive strength, expansion and pH) and microstructural properties (X-ray diffraction) of the tested mixes were asessed. The results infer that 20 % replacement level of GGBFS with SCBA produces superior compressive strength and all other results were within the permissible limits even at 40 % replacement level.

The Influence of the Properties of the Material Used for Obtaining Geopolymers on Their Structure and Compressive Strength

2017 ◽  
Vol 68 (6) ◽  
pp. 1182-1187
Author(s):  
Ilenuta Severin ◽  
Maria Vlad
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Wheat Straw ◽  
Red Mud ◽  
Blast Furnace Slag ◽  
Complex Structure ◽  
Point Of View ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag ◽  
Straw Ash

This article presents the influence of the properties of the materials in the geopolymeric mixture, ground granulated blast furnace slag (GGBFS) + wheat straw ash (WSA) + uncalcined red mud (RMu), and ground granulated blast furnace slag + wheat straw ash + calcined red mud (RMc), over the microstructure and mechanical properties of the synthesised geopolymers. The activation solutions used were a NaOH solution with 8M concentration, and a solution realised from 50%wt NaOH and 50%wt Na2SiO3. The samples were analysed: from the microstructural point of view through SEM microscopy; the chemical composition was determined through EDX analysis; and the compressive strength tests was done for samples tested at 7 and 28 days, respectively. The SEM micrographies of the geopolymers have highlighted a complex structure and an variable compressive strength. Compressive strength varied from 24 MPa in the case of the same recipe obtained from 70% of GGBFS + 25% WSA +5% RMu, alkaline activated with NaOH 8M (7 days testing) to 85 MPa in the case of the recipe but replacing RMu with RMc with calcined red mud, alkaline activated with the 50%wt NaOH and 50%wt Na2SiO3 solution (28 days testing). This variation in the sense of the rise in compressive strength can be attributed to the difference in reactivity of the materials used in the recipes, the curing period, the geopolymers structure, and the presence of a lower or higher rate of pores, as well as the alkalinity and the nature of the activation solutions used.

scholarly journals Effect of Na2SiO3/Naoh on the Compressive Strength of Inorganic Polymer Concrete Mixed with Ground Granulated Blast Furnace Slag (GGBS) At Ambient Condition

2019 ◽  
Vol 9 (2) ◽  
pp. 1222-1228
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Ambient Condition ◽  
Polymer Concrete ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Standard Size ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper aims to investigate the influence of alkaline activators solution i.e, Na2SiO3 / NaOH on compressive strength of geopolymer concrete mixed with Ground Granulated Blast furnace slag (GGBS) for constant molarity 8 M. The ratio of alkali to binder ratio is taken as 0.5 and the ratio of Na2SiO3 / NaOH is 2.5. The geopolymer mix is based on pervious sutdies. As per Indian standard size moulds for the cube, cylinder and prism are cast, cured and tested.The specimens were tested for fresh concrete properties such as slump cone test and hardened properties such as compressive strength for cubes, split tensile strength for cylinders and flexural strength for prism different days of curing under ambient temperature. Also, a microstructural study is done by using Scanning electron microscopy (SEM), Energy dispersive X-ray (EDX) for the tested sample. It is found from the test results that, with the aid of alumino-silicate solution, early strength is achieved by geopolymer concrete within 7 days under ambient condition due to the presence of ground granulated slag.

The effects of using Micro-SiO2 with Ground Granulated Blast-Furnace Slag of Esfahan Steel Company in Concrete

2015 ◽  
Vol 16 (SE) ◽  
pp. 509-517
Author(s):  
Fatemeh Sayyahi ◽  
Hamid Shirzadi
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Cement Content ◽  
Harmful Effect ◽  
Maximum Size ◽  
Steel Company ◽  
Granulated Blast Furnace Slag ◽  
Compressive Strength Of Concrete ◽  
Furnace Slag

 In this study, the properties of concrete with different amounts of Ground Granulated Blast-Furnace Slag (GGBFS) has been studied. In another part, the test deals to assess the properties of concrete containing GGBFS with micro-SiO2. The results show that the slag has pozzolan properties and its use up to 20% in the concrete, has no harmful effect on concrete properties. The simultaneous use of micro-SiO2 with blast furnace slag have little effect, as well as micro-SiO2 covers the defects caused by the use of slag. The results indicate that the use of micro-SiO2 and slag has good effects on the strength of concrete up to a certain age, so that its compressive strength is increased. Water-cement ratio was 0.42 and 12.5 mm for maximum size of aggregate and cement content in concrete was 425 kg per cubic meter. Compressive strength of concrete samples was measured at ages 7, 28, 56 and 90-day and flexural and tensile strength and water absorption after 28-day and 90 days also was measured.

Sign in / Sign up

Export Citation Format

Share Document