scholarly journals Study on Flow Field and Rotor Safety Characteristics of MSPs Based on Flow Thermo-Coupling

Processes ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 711
Author(s):  
Yiming Chen ◽  
Rongsheng Zhu ◽  
Yonggang Lu ◽  
Zhenjun Gao ◽  
Junjun Kang
Keyword(s):  
High Temperature ◽  
Equivalent Stress ◽  
Outer Edge ◽  
Cover Plate ◽  
Distribution Law ◽  
Maximum Deformation ◽  
Structural Intensity ◽  
Operation Conditions ◽  
Working Face ◽  
Different Temperatures

In order to obtain the structural intensity under the operation conditions of MSP (molten salt pump), the rotor component of MSP is taken as the research object. In this paper, the influence of material properties change on the structural performance of MSP at different temperatures is analyzed. The stress distribution and strain distribution of MSP rotor components under different loads are investigated, and the intensity calculation of MSP rotor system is carried out to explore whether it meets the intensity requirements under high temperature operation, which lays a foundation for the high temperature test of MSP. The results show that the maximum deformation position of the blade working face appears at the outer edge of the impeller. When the fluid-structure coupling is applied, the blade strain law and the strain law during thermo-coupling are similar. The effect of the temperature field on the degree of blade deformation is not significant, provided that other factors remain the same. The position where the impeller equivalent stress is the largest is mainly concentrated in the area where the blade is in contact with the front and rear cover plates at the outlet of the impeller. Different degrees of stress concentration occur in the area where the blade is in contact with the impeller hub. The distribution law of the equivalent stress on the surface of the impeller cover plate is that the equivalent stress value changes periodically along the circumferential direction of the impeller, and the number of change cycles is equal to the number of impeller blades. This study can provide a reference for the structural design of MSPs.

Stress Analysis of Tubular Turbine Based on Fluid-Structure Coupling

2012 ◽  
Vol 190-191 ◽  
pp. 1261-1265
Author(s):  
Fu Xing Zhang ◽  
Yuan Zheng ◽  
Chun Xia Yang ◽  
Xiang Long Jin ◽  
Lin Ding
Keyword(s):  
Stress Concentration ◽  
Working Conditions ◽  
Guide Vane ◽  
Equivalent Stress ◽  
Outer Edge ◽  
Fluid Structure ◽  
Maximum Deformation ◽  
Water Head ◽  
Maximum Equivalent Stress ◽  
Maximum Water

A brief introduction of fluid-structure coupling and its classification were given, then according to the solving characteristics and application conditions of different coupling methods; sequential coupling method is chosen to calculate the stress distribution of a tide power plant tubular turbine. Stress calculations of the tubular turbine were conducted under the maximum water head, the designed water head, the average water head and the minimum water head working conditions in ANSYS Workbench. The research shows that in all of the four calculated working conditions, the maximum equivalent stress of the runner is located at the connection between the blades and the hub where stress concentration is obvious; the maximum deformation of the runner lies in the outer edge of the blades and the deformation increases from the root to the outer edge; the maximum equivalent stress of the guide vane is located at the root and the maximum deformation lies in the outer edge. The maximum value of maximum equivalent stress of the runner and the guide vane occurs on the maximum water head working condition, whereas it is far less than the material yield limit, which means that static stress will not lead to the cracks of the blade or the guide vane. But it is still necessary to avoid stress concentration appearing periodically in case it causes fatigue failure.

scholarly journals Analysis of Mechanical Characteristics of Impeller of Spray Duster Based on ANSYS Workbench

2022 ◽  
Vol 2152 (1) ◽  
pp. 012046
Author(s):  
Kunpeng Sun ◽  
Lihong Yang ◽  
Jicheng Li
Keyword(s):  
Vibration Frequency ◽  
Mechanical Characteristics ◽  
Equivalent Stress ◽  
Outer Edge ◽  
Allowable Stress ◽  
Maximum Deformation ◽  
Maximum Equivalent Stress ◽  
Interference Frequency ◽  
The Stability ◽  
Ansys Workbench

Abstract The spray dustless machine is an important environmental protection equipment for harnessing haze. The booster impeller of the spray dustless machine is one of the decisive factors of the booster capacity. The stability of the blade directly determines the reliability of the spray duster. In this paper, ANSYS Workbench is used to analyze the mechanical characteristics of a certain type of spray dustless blade. The results show that: under the rated condition, the maximum equivalent stress of the impeller is 55.6Mpa, which is far less than the allowable stress of the impeller material 415Mpa, the maximum deformation of the circumferential position at the bottom of the blade is 1.2mm, and other deformation positions are mainly the outer edge of the blade, which can be optimized later. The interference frequency is far away from the vibration frequency of the first two modes, so resonance will not occur.

scholarly journals GERMINATION AND VIGOUR IN SEEDS OF THE COWPEA IN RESPONSE TO SALT AND HEAT STRESS

2019 ◽  
Vol 32 (1) ◽  
pp. 143-151 ◽  
Author(s):  
Luma Rayane de Lima Nunes ◽  
Paloma Rayane Pinheiro ◽  
Charles Lobo Pinheiro ◽  
Kelly Andressa Peres Lima ◽  
Alek Sandro Dutra
Keyword(s):  
Salt Stress ◽  
Heat Stress ◽  
High Temperature ◽  
Low Temperature ◽  
Vigna Unguiculata ◽  
Salt Concentration ◽  
Dry Weight ◽  
Germination Percentage ◽  
Different Types ◽  
Different Temperatures

ABSTRACT Salinity is prejudicial to plant development, causing different types of damage to species, or even between genotypes of the same species, with the effects being aggravated when combined with other types of stress, such as heat stress. The aim of this study was to evaluate the tolerance of cowpea genotypes (Vigna unguiculata L. Walp.) to salt stress at different temperatures. Seeds of the Pujante, Epace 10 and Marataoã genotypes were placed on paper rolls (Germitest®) moistened with different salt concentrations of 0.0 (control), 1.5, 3.0, 4.5 and 6.0 dS m-1, and placed in a germination chamber (BOD) at temperatures of 20, 25, 30 and 35°C. The experiment was conducted in a completely randomised design, in a 3 × 4 × 5 scheme of subdivided plots, with four replications per treatment. The variables under analysis were germination percentage, first germination count, shoot and root length, and total seedling dry weight. At temperatures of 30 and 35°C, increases in the salt concentration were more damaging to germination in the Epace 10 and Pujante genotypes, while for the Marataoã genotype, damage occurred at the temperature of 20°C. At 25°C, germination and vigour in the genotypes were higher, with the Pujante genotype proving to be more tolerant to salt stress, whereas Epace 10 and Marataoã were more tolerant to high temperatures. Germination in the cowpea genotypes was more sensitive to salt stress when subjected to heat stress caused by the low temperature of 20°C or high temperature of 35°C.

scholarly journals Experimental Investigation of Wave Velocity-Permeability Model for Granite Subjected to Different Temperature Processing

Geofluids ◽  
2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Guanghui Jiang ◽  
Jianping Zuo ◽  
Teng Ma ◽  
Xu Wei
Keyword(s):  
Particle Size ◽  
High Temperature ◽  
Wave Velocity ◽  
Pore Fluid ◽  
Rock Matrix ◽  
Permeability Model ◽  
Wave Velocities ◽  
Before And After ◽  
Different Temperatures ◽  
Increasing Temperature

Understanding the change of permeability of rocks before and after heating is of great significance for exploitation of hydrocarbon resources and disposal of nuclear waste. The rock permeability under high temperature cannot be measured with most of the existing methods. In this paper, quality, wave velocity, and permeability of granite specimen from Maluanshan tunnel are measured after high temperature processing. Quality and wave velocity of granite decrease and permeability of granite increases with increasing temperature. Using porosity as the medium, a new wave velocity-permeability model is established with modified wave velocity-porosity formula and Kozeny-Carman formula. Under some given wave velocities and corresponding permeabilities through experiment, the permeabilities at different temperatures and wave velocities can be obtained. By comparing the experimental and the theoretical results, the proposed formulas are verified. In addition, a sensitivity analysis is performed to examine the effect of particle size, wave velocities in rock matrix, and pore fluid on permeability: permeability increases with increasing particle size, wave velocities in rock matrix, and pore fluid; the higher the rock wave velocity, the lower the effect of wave velocities in rock matrix and pore fluid on permeability.

A Method for Predicting the Behavior of Plastics at Different Temperatures

2014 ◽  
Vol 1039 ◽  
pp. 107-111
Author(s):  
Yang Chen ◽  
Gui Qin Li ◽  
Bin Ruan ◽  
Xiao Yuan ◽  
Hong Bo Li
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Constitutive Model ◽  
Research And Development ◽  
Mechanical Behavior ◽  
Plastic Material ◽  
Different Temperatures ◽  
Plastic Parts

The mechanical behavior of plastic material is dramatically sensitive to temperature. An method is proposed to predict the mechanical behavior of plastics for cars, ranging from low-temperature low temperature ≤-40°C to high temperature ≥80°C. It dominates the behavior of plastic material based on improved constitutive model in which the parameters adjusted by a series of tests under different temperatures. The method is validated with test and establishes the basis for research and development of plastic parts for automobile as well.

Experimental Research on Bond Strength between Rebar and Concrete after High Temperature

2011 ◽  
Vol 71-78 ◽  
pp. 1057-1061 ◽  
Author(s):  
Ke Fang Yin ◽  
Yang Han ◽  
Yi Liu
Keyword(s):  
Reinforced Concrete ◽  
High Temperature ◽  
Bond Strength ◽  
Experimental Research ◽  
Bonding Strength ◽  
Different Temperatures ◽  
Ultimate Bond Strength

With the centrally pulling-out test, the bond strength of reinforced concrete is measured with different temperatures and different cooling ways after high temperature; and the ultimate bond strength and slip of reinforced and concrete under different conditions are analyzed. The results show that the bonding strength declines gradually with the increase of temperature, and the ultimate slippage also decreases gradually.

scholarly journals Investigation of Fatigue Behavior of ABS and PC-ABS Polymers at Different Temperatures

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1818
Author(s):  
Andrea Mura ◽  
Alessando Ricci ◽  
Giancarlo Canavese
Keyword(s):  
High Temperature ◽  
Room Temperature ◽  
Working Condition ◽  
Fatigue Behavior ◽  
Polymeric Materials ◽  
Cyclic Loads ◽  
Structural Components ◽  
Working Temperature ◽  
Different Temperatures ◽  
Positive Effect

Plastics are widely used in structural components where cyclic loads may cause fatigue failure. In particular, in some applications such as in vehicles, the working temperature may change and therefore the strength of the polymeric materials. In this work, the fatigue behavior of two thermoplastic materials (ABS and PC-ABS) at different temperatures has been investigated. In particular, three temperatures have been considered representing the working condition at room temperature, at low temperature (winter conditions), and high temperature (summer conditions and/or components close to the engine). Results show that high temperature have big impact on fatigue performance, while low temperatures may also have a slight positive effect.

scholarly journals Conidia sporulation of Pyricularia oryzae in segments of wheat plants under six different temperatures

2020 ◽  
Vol 50 (4) ◽  
Author(s):  
Marcos Kovaleski ◽  
João Leodato Nunes Maciel ◽  
Gustavo Bilibio dos Santos ◽  
Alieze Nascimento da Silva ◽  
Carolina Cardoso Deuner
Keyword(s):  
High Temperature ◽  
Petri Dish ◽  
Pyricularia Oryzae ◽  
Causal Agent ◽  
Temperature Conditions ◽  
Wheat Blast ◽  
Conidia Production ◽  
Different Temperatures

ABSTRACT: Wheat blast is known for developing itself more intensely under relatively high temperature conditions but many aspects related to its epidemiology remain unknown. The objective of this research was to evaluate the sporulative capacity of Pyricularia oryzae Triticum (Pot), the causal agent of wheat blast, in tissues of wheat plants under different temperatures degrees. Wheat plants of the cultivar Anahuac 75, susceptible to blast, were inoculated in the stage of flowering with conidial suspensions (105 conidia/mL) of the Pot isolates Py 12.1.209 and Py 12.1.132. Seven days after the inoculation, plants were cut in the following segments: leaves, stems and rachis (with blast severity ranging from 40 to 60%). Groups of each one of the three plant segments with the lesions were disposed in Petri-dish moist chambers, that were submitted to six different temperature treatments (18, 21, 24, 27, 30 and 33 °C). The most appropriate model that related the conidia production with temperature was identified in the evaluations conducted with stems. The established equations allowed identifying that the highest production of conidia of Pot occurs between 24 and 27 °C.

scholarly journals Temperature Effects on Dormancy Completion of Vegetative Buds in Apple

2003 ◽  
Vol 128 (5) ◽  
pp. 636-641 ◽  
Author(s):  
Amos Naor ◽  
Moshe Flaishman ◽  
Raphael Stern ◽  
Aharon Moshe ◽  
Amnon Erez
Keyword(s):  
High Temperature ◽  
Dominance Effect ◽  
Chilling Temperature ◽  
Flower Buds ◽  
Diurnal Cycles ◽  
Relative Contribution ◽  
Vegetative Buds ◽  
Lateral Buds ◽  
Different Temperatures ◽  
Chilling Hours

The relative contribution of various temperatures to dormancy completion of lateral vegetative apple [Malus sylvestris (L.) Mill. var. domestica (Borkh.) Mansf.] buds was studied quantitatively on whole container-grown trees. Trees were exposed continuously to 10 different temperatures and also to daily alternating temperatures in a 24-hour cycle. In addition, fully chilled vertically and horizontally positioned shoots were compared under forcing conditions. No budbreak occurred in shoots chilled above 12.5 °C. There was a steep increase in budbreak as the chilling temperature fell from 12.5 to 7.5 °C. There was little difference in the level of budbreak on shoots chilled between 7.5 and 0 °C. The relative contribution of temperature to chilling accumulation in apple found in our study differs from what has been proposed for stone fruit and for apple in previous studies, especially at temperatures <6 °C. The length of exposure to forcing conditions required to initiate budbreak diminished as the chilling temperature was reduced. No additional bud-break was apparent on shoots chilled longer than 2100 chilling hours. The chilling requirement found here for lateral vegetative buds is much higher than that needed for terminal vegetative and flower buds. Trees that were exposed to daily alternating temperatures had lower levels of budbreak when the high temperature in the diurnal cycle was greater than 14 °C. Practically no budbreak was apparent on trees that were exposed to diurnal cycles with a high temperature of 20 °C for 8 hours. Budbreak on horizontally positioned trees was more than twice that on the vertically positioned trees, emphasizing the magnitude of the apical dominance effect and its strong masking of the chilling effect on lateral buds in vertically grown apple trees. Based on the data collected here we propose a new response curve for vegetative budbreak in `Golden Delicious·apple, within a temperature range between 0 to 15 °C.

scholarly journals Compressibility behavior of Boron (Tincal) added to sand-bentonite mixtures under different temperatures

2020 ◽  
Vol 205 ◽  
pp. 09007
Author(s):  
Sukran Gizem Alpaydin ◽  
Yeliz Yukselen-Aksoy
Keyword(s):  
High Temperature ◽  
Volume Deformation ◽  
Landfill Liners ◽  
Low Thermal Expansion ◽  
Boron Minerals ◽  
Different Temperatures ◽  
Increasing Temperature ◽  
Waste Repositories ◽  
Oedometer Tests ◽  
Soil Changes

The importance of thermal behaviour of soils has increased significantly with increasing number of energy structures. There is a need for soils, which show design criteria (strength, permeability, etc.) performance during their life under high temperature or thermal cycles. In the literature studies, it was observed that the volumetric deformation of the soil changes with increasing temperature. Sand-bentonite mixtures generally act as impervious barrier in areas such as nuclear waste repositories, landfill liners etc. These mixtures will be exposed to high temperature; therefore, their engineering performance should not alter under high temperature. Boron is used in the industry for high temperature resistance, flexibility, lightness, power and ease of production. Boron minerals have very low thermal expansion and they are also resistant to thermal shocks. For that reason, the properties of sand-bentonite mixtures can be improved by boron additives at high temperatures. In this study, volume deformation behavior of sand-bentonite mixtures was determined in the presence of tincal. The oedometer tests were performed under room temperature and 80°C.

Sign in / Sign up

Export Citation Format

Share Document