scholarly journals Bacteria Adhesion of Textiles Influenced by Wettability and Pore Characteristics of Fibrous Substrates

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 223
Author(s):  
Tahmineh Hemmatian ◽  
Halim Lee ◽  
Jooyoun Kim
Keyword(s):  
Pore Size ◽  
Pore Volume ◽  
Capillary Flow ◽  
Morphological Characteristics ◽  
Severe Infection ◽  
Total Pore Volume ◽  
Initial Step ◽  
Poly Lactic Acid ◽  
Pore Characteristics ◽  
Bacteria Adhesion

Bacteria adhesion on the surface is an initial step to create biofouling, which may lead to a severe infection of living organisms and humans. This study is concerned with investigating the textile properties including wettability, porosity, total pore volume, and pore size in association with bacteria adhesion. As model bacteria, Gram-negative, rod-shaped Escherichia coli and the Gram-positive, spherical-shaped Staphylococcus aureus were used to analyze the adhesion tendency. Electrospun webs made from polystyrene and poly(lactic acid) were used as substrates, with modification of wettability by the plasma process using either O2 or C4F8 gas. The pore and morphological characteristics of fibrous webs were analyzed by the capillary flow porometer and scanning electron microscopy. The substrate’s wettability appeared to be the primary factor influencing the cell adhesion, where the hydrophilic surface resulted in considerably higher adhesion. The pore volume and the pore size, rather than the porosity itself, were other important factors affecting the bacteria adherence and retention. In addition, the compact spatial distribution of fibers limited the cell intrusion into the pores, reducing the total amount of adherence. Thus, superhydrophobic textiles with the reduced total pore volume and smaller pore size would circumvent the adhesion. The findings of this study provide informative discussion on the characteristics of fibrous webs affecting the bacteria adhesion, which can be used as a fundamental design guide of anti-biofouling textiles.

scholarly journals Mineral compositional controls on the porosity of black shales from the Wufeng and Longmaxi Formations (Southern Sichuan Basin and its surroundings) and insights into shale diagenesis

2018 ◽  
Vol 36 (4) ◽  
pp. 665-685
Author(s):  
Mei Han ◽  
Chao Han ◽  
Zuozhen Han ◽  
Zhigang Song ◽  
Wenjian Zhong ◽  
...  
Keyword(s):  
Organic Matter ◽  
Pore Size ◽  
Pore Volume ◽  
Total Pore Volume ◽  
Black Shales ◽  
Carbonate Content ◽  
Pore Sizes ◽  
Pore Size Distributions ◽  
Shale Composition ◽  
The Relationship

The effects of brittle minerals in shale diagenesis on shale pores remain controversial and it is difficult to quantify directly. However, the relationship between brittle minerals and shale pores could provide indirect guidance regarding diagenesis processes in post-mature marine shales. In this study, the pore size distribution was determined, and the relationship between pore volume and shale composition was examined in shale samples with different total organic carbon contents from the Wufeng and Longmaxi Formations, with the objective of distinguishing pore size ranges in organic matter and inorganic minerals, respectively, and studying shale diagenesis. The samples of the Wufeng and Longmaxi shales are composed of clay minerals, calcite, dolomite, quartz, feldspar, and some minor components. The pore size distributions, which were determined using nitrogen adsorption isotherm analysis of shale and kerogen, show similar trends for pore sizes less than approx. 6.5 nm but different trends for larger pore sizes. Mercury injection saturation shows that macropores account for 14.4–22% of the total pore volume. Based on a series of crossplots describing the relationships between shale composition and pore volume or porosity associated with different pore sizes as well as on scanning electron microscopy observations, organic matter pores were found to comprise most of the micro-mesopores (pore diameters < 6.5 nm). Organic matter pores and intraparticle pores associated with carbonate constitute the majority of mesopores (pore diameters 6.5–50 nm). Finally, interparticle pores associated with quartz comprise the majority of the macropores. The mesopores associated with carbonate were formed by dissolution during diagenesis, whereas the macropores associated with quartz are the remainders of the original interparticle pores. Mesopore volumes increase with increasing carbonate content while macropore volumes decrease due to the ‘pore size controlled solubility’ effect, which causes dissolved calcium carbonate to precipitate in larger macropores.

The Influence of Sinterng Temperature on the Phase, Microstructure and Textual Properties of Hollow Hydroxyapatite Microspheres

2011 ◽  
Vol 239-242 ◽  
pp. 2274-2279 ◽  
Author(s):  
Ying Chun Wang ◽  
Wen Hai Huang ◽  
Ai Hua Yao ◽  
De Ping Wang
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Sintering Temperature ◽  
Total Pore Volume ◽  
Precipitation Method ◽  
Simple Method ◽  
Air Atmosphere

A simple method to prepare hollow hydroxyapatite (HAP) microspheres with mespores on the surfaces is performed using a precipitation method assisted with Li2O-CaO-B2O3(LCB) glass fabrication process. This research is concerned with the effect of sintering temperature on the microstructure evolution, phase purity, surface morphology, specific surface area, and porosity after sintering process. The microspheres were sintered in air atmosphere at temperatures ranging from 500 to 900 °C. The starting hollow HAP microspheres and the sintered specimens were characterized by scanning electron microscope, X-ray diffractometer, specific surface area analyzer, and Hg porosimetry, respectively. The as-prepared microspheres consisted of calcium deficient hydroxyapatite. The results showed that the as-prepared hollow HAP microspheres had the highest specific surface areas, and the biggest total pore volume. The pore size distribution of the as-prepared hollow HAP microspheres were mainly the mesopores in the range of 2～40 nm. The specific surface area and total pore volume of hollow HAP microspheres decreased with increasing sintering temperature. Whereas the mean pore size increased with increasing sintering temperature. It showed that at 700°C, Ca-dHAP decomposes into a biphasic mixture of HAP and β-calcium phosphate(TCP).

scholarly journals Experimental Investigation of the Macroscopic Behavior and Microstructure Property Evolution of Hardened Cement Consolidated Tailings

Minerals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 6 ◽  
Author(s):  
Xiang Sun ◽  
Yunbing Hou
Keyword(s):  
Compressive Strength ◽  
Pore Size ◽  
Pore Volume ◽  
Mercury Intrusion Porosimetry ◽  
Mining Industry ◽  
Total Pore Volume ◽  
Hardened Cement ◽  
Curing Period ◽  
Strength Tests ◽  
Curing Age

Surface cement consolidated tailings disposal has recently been proposed to manage tailings in the modern mining industry because it can reduce or eliminate the disadvantages of traditional tailings storage. In this study, the evolution of the macro performance and microstructure characteristics of cement consolidated tailing samples during the curing period were determined by unconfined compressive strength tests, permeability tests, scanning electron microscopy (SEM) observations, and mercury intrusion porosimetry (MIP) tests, respectively. The results show that the curing time notably affected the macro performance and microstructural properties of the hardened cement consolidated tailings samples. As the curing age increases, the compressive strength increases nonlinearly and the growth rate decreases; the permeability decreases rapidly first, then gradually stabilizes, and finally reaches a stable value; the morphology of the hydration products and microstructures continues to evolve with the hydration process; the total pore volume decreases slightly, whereas the critical pore size decreases significantly. The proportion of the pore volume in different pore size ranges can also be affected by the curing age, which results in a large pore (>200 nm) decrease, and the small pores (<200 nm) increased. In this process, the filling effect plays a major role.

Effect of Heat-Treatment in Ar Atmosphere on Pore Structure of Carbonaceous Materials from Polysiloxane

2014 ◽  
Vol 602-603 ◽  
pp. 279-284
Author(s):  
Li Qun Duan ◽  
Chen Chen Zhang ◽  
Qing Song Ma ◽  
Zhao Hui Chen
Keyword(s):  
Heat Treatment ◽  
Pore Structure ◽  
Pore Size ◽  
Pore Volume ◽  
Average Pore Size ◽  
Total Pore Volume ◽  
Treatment Temperature ◽  
Carbonaceous Materials ◽  
Average Pore ◽  
Pore Size Distributions

Nanoporous carbonaceous materials derived from polysiloxane were first prepared by pyrolysis at 1300°C followed with hydrofluoric acid (HF) etching treatment. Their thermal stability of pore structure in inert condition was investigated in this paper by nitrogen adsorption technique in detail. The specific surface area (SSA) and pore volume (total pore volume, micropore volume, mesopore volume) decreased continually in the heat-treatment temperature range of 1000~1400°C. The average pore size almost kept the same with the raw sample. However, when the temperature exceeded 1400°C, the micropore interconnection began transforming to mesopore structure, which led to the decline of SSA and the increase of average pore size. Furthermore, the pore size distributions (PSDs) curves showed that heat-treatment had an advantage on the transition process of pore structure from disorder to regularity to some extent when heat-treated in the range 1000~1400°C for the most possible reason of relief of residue strain in the carbonaceous materials.

Pore Structure Of Hydrated Cement Determined By Mercury Porosimetry And Nitrogen Sorption Techniques.

1988 ◽  
Vol 137 ◽  
Author(s):  
Yahia Abdel-Jawad ◽  
Will Hansen
Keyword(s):  
Pore Structure ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Pore Volume ◽  
Mercury Porosimetry ◽  
Total Pore Volume ◽  
Curing Temperature ◽  
Vycor Glass ◽  
Degree Of Hydration

AbstractThe pore structure (i.e. total pore volume, surface area and pore-size distribution curves) was measured using mercury porosimetry and nitrogen sorption. Hydrated portland cement (type I) of water-cement (w/c) ratios 0.3, 0.4 and 0.6 by weight was analyzed at three degrees of hydration (i.e., 30%, 50% and 80%; 70% for the 0.3 w/c system) corresponding to low, intermediate and high levels of hydration. The effect of curing temperature (3°, 23°, and 43°C) on pore structure was also studied. The two techniques were evaluated as well on porous Vycor glass, which has a narrow pore size distribution in the size range accessible to both. Results obtained by both techniques on porous Vycor glass agreed well. However neither technique can be used alone to study the entire pore structure in well-hydrated cement due to the wide range in pore sizes and the presence of micropores. Due to the unstable pore structure in cement a specimen treatment procedure such as methanol replacement, combined with volume-thickness (V-t) analysis, is necessary in order to measure the micropores. At low hydration values the pore structure can be estimated by mercury intrusion porosimetry (MIP). At higher hydration values, however, this technique underestimates total pore volume and surface area due to the presence of micropores which MIP cannot determine. In the pore size range of overlap, higher pore volumes were obtained with MIP. Nitrogen V-t analysis shows that micropores are more pronounced with lower w/c ratios. This finding is consistent with pore size distribution curves obtained by MIP. For a given w/c ratio and degree of hydration the total pore volume measured by MIP was found to be independent of curing temperature in the temperature range studied. At any w/c ratio, capillary porosity is controlled by degree of hydration alone.

Relationship between pore size distributions and physical properties of clay soils

Soil Research ◽  
1974 ◽  
Vol 12 (2) ◽  
pp. 107 ◽  
Author(s):  
ID Sills ◽  
LAG Aylmore ◽  
JP Quirk
Keyword(s):  
Particle Size ◽  
Pore Size ◽  
Pore Volume ◽  
Total Pore Volume ◽  
Particle Size Analysis ◽  
The Other ◽  
Clay Soils ◽  
Size Analysis ◽  
Size Distributions ◽  
Pore Size Distributions

Pore size distributions using mercury injection and nitrogen sorption techniques were determined on a number of soils classified as clays on the basis of particle size analysis. Some of these soils exhibit markedly different consistencies during texturing and undergo changes in texture during prolonged manipulation, e.g. subplastic, superplastic and self-mulching soils. The pore size distributions for these soils do not differ significantly from those obtained for the normal labile clay soil in the pore size range 2 nm to 50 �m. The clay soils examined, with the exception of the krasnozem, have the majority of their pore volume within pores smaller than 10 nm with the predominant pore size centred around 3 nm plate separation. In the case of the krasnozem, the particle size analysis does not correspond to the texture assessment as a clay loam. Surface and subsoil samples of the krasnozem have high porosities and predominant plate separations of 6 nm. They consequently possess significantly different pore size distributions from the other clays. In the case of the surface sample, only a small proportion of its total pore volume is in pores smaller than 10 nm. These differences in pore structure observed between the krasnozem and the other soils examined may result from differences in mineralogy, and in particular from the high sesquioxide content of the krasnozem.

scholarly journals Pore Structural Features of Granite under Different Temperatures

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6470
Author(s):  
Hongmei Gao ◽  
Yongwei Lan ◽  
Nan Guo
Keyword(s):  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Pore Volume ◽  
Saturation Pressure ◽  
Total Pore Volume ◽  
Structural Features ◽  
Pore Throat ◽  
Throat Radius ◽  
Median Pore

To explore the effects of thermal actions on the pore structural features of granite, scanning electron microscope (SEM) and mercury injection experiments were carried out on granite after thermal treatment (25 °C to 400 °C). The pore structure was investigated from various perspectives, including the capillary pressure curve, the pore–throat ratio, the median saturation pressure, the median pore–throat radius, the porosity, the pore volume, and the pore size distribution. Based on mercury intrusion test data, the Winland model of permeability prediction was modified for a high-temperature tight granite reservoir. The results showed that: (1) As the temperature rose, the mercury injection curve was gradually flattened, and the mercury ejection efficiency gradually increased. Meanwhile, the pore–throat ratio and the median saturation pressure decreased exponentially, and the pore connectivity was enhanced. (2) The median pore–throat radius and the porosity of granite increased exponentially as the temperature increased. Above 200 °C, the median pore–throat radius and the porosity increased substantially. (3) The pore volumes of the transitional pores, mesopores and macropores, and the total pore volume inside the granite, increased as the temperature rose. Especially above 200 °C, the transitional pores and the mesopores were prominently developed, and the pore volumes of the transitional pores and the mesopores took up a significantly greater proportion of the total pore volume. (4) As the temperature rose, the pore size distribution of granite became more extensive, the pore–throat structure was obviously developed, and the pore–throat connectivity was enhanced. (5) The relationship between the micropores’ characteristic parameters and the macro-permeability in engineering was established though a modified Winland model, and the modified Winland model had a better prediction effect. The findings provide a solid basis for rock geothermal mining projects and related geotechnical engineering.

scholarly journals Microstructure and pore structure of polymer-cement composite joint sealants

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Chuanxin Lou ◽  
Jinyu Xu ◽  
Tengjiao Wang ◽  
Weibo Ren
Keyword(s):  
Pore Structure ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Pore Volume ◽  
Total Pore Volume ◽  
Cement Composite ◽  
Low Grade ◽  
Composite Joint ◽  
Fractal Characteristics

AbstractUtilizing methods such as scanning electron microscopy observation and mercury intrusion porosimetry, this paper investigates the basic microstructure and pore structure properties of polymer-cement composite joint sealants for pavements, and analyzes the effects and rules of various material types, ratio parameters and processing conditions. Further, the fractal characteristics and variation rules of pore size distribution are investigated for the joint sealants by introducing the fractal theory. The results show that changes in material type, ratio parameter and processing condition produce insignificant effects on the basic microstructure properties and configuration of joint sealants, with effects reflected primarily in the change of sealant pore structure. Measures like increasing the powder-liquid ratio and cement ratio, blending with sulphoaluminate cement or mica powder, adding latex powder or coupling agent, cold drawing and hot pressing, as well as ultraviolet irradiation treatment are all capable of reducing the total pore volume of joint sealants and refining their pore structure. In contrast, opposite effects are yielded when low-grade cement is used, styrene-acrylic emulsion is blended, or plasticizer is added. Additionally, after blending with talc powder or adding carbon fiber additive, the total pore volume of joint sealants remains basically unchanged or reduced, despite the coarsened pore structure. The total pore volume of joint sealants increases after wet–dry cycling treatment, while no obvious change in the pore size distribution is observed. Pore size distribution of the studied joint sealants presents distinct fractal characteristics, and the corresponding fractal dimension of pore surface area ranges between 2.6 and 2.8.

Effect of air-drying and critical point drying on the porosity of clay soils

1984 ◽  
Vol 21 (1) ◽  
pp. 181-185 ◽  
Author(s):  
C. R. De Kimpe
Keyword(s):  
Organic Matter ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Critical Point ◽  
Size Distribution ◽  
Pore Volume ◽  
Organic Matter Content ◽  
Total Pore Volume ◽  
Clay Soils ◽  
Critical Point Drying

Samples from four surface and one subsurface horizons of clay-rich soils from Quebec were air-dried and critical point dried. In the latter samples, the total pore volume was 19–84% larger than in the former samples. The total pore volume, determined by mercury intrusion porosimetry and density measurements, was subdivided into large (> 8.8 μm), medium, and small (< 0.19 μm) pores. The effect of drying on these pores was estimated. Medium-sized pores were affected most by the drying technique, followed next by the large pores, and finally by the small pores. The modifications due to drying could not be explained adequately by shrinkage and it was assumed, from the pore-size distribution curves, that organic matter content had a buffer effect on particle reorganization. Keywords: critical point drying, clay soils, pore volume, pore-size distribution, organic matter.

Sign in / Sign up

Export Citation Format

Share Document