scholarly journals Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 950
Author(s):  
Hongtao Cao ◽  
Beijun Liu ◽  
Yiwen Ye ◽  
Yunfang Liu ◽  
Peng Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
The Self ◽  
Reinforced Composites ◽  
Two Phase ◽  
Reinforced Composite ◽  
Transmission Electron ◽  
The Matrix ◽  
Ft Ir ◽  
The Cross

Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40–60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

scholarly journals TEM observation of precipitates and their role to mechanical properties in Ti-5553 alloy heated to some temperatures up to 923 K

2020 ◽  
Vol 321 ◽  
pp. 11035
Author(s):  
E. Sukedai ◽  
E. Aeby-Gautier ◽  
M. Dehmas
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Hardening Mechanism ◽  
Transmission Electron ◽  
The Matrix ◽  
Higher Temperature ◽  
Shearing Mechanism ◽  
Hardness Values ◽  
Measured Hardness

A Ti-5553 specimen was continuously heated to 923 K and simultaneously in-situ HEXRD profiles were taken. In addition, specimens heated at the same rate to several temperatures up to 923 K and further quenched were observed by transmission electron microscopy. Based on both results obtained, transformation sequence was clarified, precipitations of ω-, α”iso- and α-phases were confirmed, and size and density of these precipitates were measured. Hardness values of those specimens were also measured. The hardening mechanism was considered as shearing-mechanism for specimens aged at lower temperatures and by-pass one for specimens aged at higher temperature. An attempt of distinction between α”iso - and α-precipitates was also tried. Both precipitates were in needle-like shape and a possibility was suggested by measuring angles between two needle-shape precipitates on {110} of the matrix and comparing with each other.

scholarly journals Effect of Two-Stage Homogenization Heat Treatment on Microstructure and Mechanical Properties of AA2060 Alloy

Crystals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 40
Author(s):  
Chaoyang Chaoyang ◽  
Guangjie Guangjie ◽  
Lingfei Lingfei ◽  
Fei Fei ◽  
Lin Lin
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Cast Alloy ◽  
Hardness Test ◽  
Test Methods ◽  
Al Alloy ◽  
Two Stage ◽  
Homogenization Treatment ◽  
Transmission Electron ◽  
The Matrix

The microstructure evolution of AA2060 Al alloy containing Li during two-stage homogenization treatment was investigated by optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), differential scanning calorimeter (DSC), transmission electron microscopy (TEM), mechanical properties and Vickers micro-hardness test methods. The results demonstrate that severe precipitation of θ(Al2Cu) and S(Al2CuMg) phase existed in the as-cast alloy, especially in the center position. Cu elements were concentrated at grain boundary and gradually decreased from the boundary to the interior. Numerous eutectic phases of θ(Al2Cu) and S (Al2CuMg) containing Zn and Ag elements were segregated at grain boundaries. The overheating temperature of the as-cast alloy is 497 °C. After two-stage homogenization treatment, the θ(Al2Cu) and S (Al2CuMg) in the surface, middle and center positions were completely dissolved into the matrix, thus achieved uniform homogenization effect. Moreover, water cooling could prevent the precipitation after homogenization, which provided good performance of the studied alloy. The optimum two-stage homogenization treatment of AA2060 alloy was 460 °C/4 h + 490 °C/2 4 h. The homogenization kinetic analysis was discussed as well.

scholarly journals Enhancement of Mechanical and Thermal Properties of Polylactic Acid/Polycaprolactone Blends by Hydrophilic Nanoclay

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Chern Chiet Eng ◽  
Nor Azowa Ibrahim ◽  
Norhazlin Zainuddin ◽  
Hidayah Ariffin ◽  
Wan Md. Zin Wan Yunus ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Polylactic Acid ◽  
Mechanical Analysis ◽  
Basal Spacing ◽  
Mechanical And Thermal Properties ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
The Matrix ◽  
Thermal Stability Of

The effects of hydrophilic nanoclay, Nanomer PGV, on mechanical properties of Polylactic Acid (PLA)/Polycaprolactone (PCL) blends were investigated and compared with hydrophobic clay, Montmorillonite K10. The PLA/PCL/clay composites were prepared by melt intercalation technique and the composites were characterized by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). FTIR spectra indicated that formation of hydrogen bond between hydrophilic clay with the matrix. XRD results show that shifting of basal spacing when clay incorporated into polymer matrix. TEM micrographs reveal the formation of agglomerate in the composites. Based on mechanical properties results, addition of clay Nanomer PGV significantly enhances the flexibility of PLA/PCL blends about 136.26%. TGA showed that the presence of clay improve thermal stability of blends. DMA show the addition of clay increase storage modulus and the presence of clay Nanomer PGV slightly shift two Tg of blends become closer suggest that the presence of clay slightly compatibilizer the PLA/PCL blends. SEM micrographs revealed that presence of Nanomer PGV in blends influence the miscibility of the blends. The PLA/PCL blends become more homogeneous and consist of single phase morphology.

Electron Microscopy of Irradiated and Mechanically Tested Tungsten

1967 ◽  
Vol 25 ◽  
pp. 314-315
Author(s):  
Robert C. Rau ◽  
Robert L. Ladd ◽  
John Moteff
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Threshold Region ◽  
Body Centered Cubic ◽  
Defect Clusters ◽  
Neutron Fluences ◽  
Transmission Electron ◽  
Abrupt Changes ◽  
The Matrix

As part of a program investigating the effects of neutron irradiation on the physical and mechanical properties of body centered cubic refractory metals, transmission electron microscopy has been carried out on irradiated tungsten after tensile and creep-rupture testing. These observations have shown the existence of a fluence threshold region between 5.9 × 1018 and 3.8 × 1019 nvt (E < 1 MeV) over which both microstructure and mechanical properties undergo abrupt changes.A series of specimens irradiated at pile ambient temperature (∼ 70°C) to various fast neutron fluences and subsequently tensile tested at 400°C showed dramatic evidence of the build-up of defect clusters with increasing exposure. The starting microstructure present in undeformed button heads of unirradiated control specimens consisted of large tungsten grains divided into many small subgrains by hexagonal dislocation networks, as shown in Figure 1. Irradiation to neutron fluences of 4.0 and 5.9 × 1018 nvt produced tiny dot clusters in the matrix, as shown in Figure 2.

Investigation on B, Cr Doped Ni3Al Alloy Prepared by Self-Propagation High-Temperature Synthesis and Hot Extrusion

2013 ◽  
Vol 747-748 ◽  
pp. 124-131 ◽  
Author(s):  
Li Yuan Sheng ◽  
Jian Ting Guo ◽  
Chao Yuan ◽  
F. Yang ◽  
G.S. Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
High Temperature ◽  
Hot Extrusion ◽  
The Self ◽  
Al Alloy ◽  
Temperature Synthesis ◽  
X Ray ◽  
High Temperature Synthesis ◽  
Transmission Electron

The Ni3Al and Ni3Al-B-Cr alloys were fabricated by the self-propagation high-temperature synthesis with hot extrusion method. Their microstructure and mechanical properties were studied by using combination of X-ray diffraction, optical microscopy, transmission electron microscopy and compression test. Analysis of X-ray spectra exhibited that the elemental powders had been transformed to the Ni3Al phase after the self-propagation high-temperature synthesis processing. Microstructure examination showed that the alloy without extrusion consisted of coarse and fine grains, but the subsequent hot extrusion procedure homogenized the grain size and densified the alloy obviously. Transmission electron microscopy observations on the Ni3Al alloy revealed that Ni3Al, γ-Ni and Al2O3 particles were the main phases. When the boron and chromium were added, besides the β-NiAl phase, α-Cr phase and some Cr7Ni3 particles with stacking faults inside were observed. In addition, a lot of substructure and high-density dislocation arrays were observed in the extruded part, which indicated that the subsequent extrusion had led to great deformation and partly recrystallizing in the alloy. Moreover, the subsequent extrusion procedure redistributed the Al2O3 particles and eliminated the γ-Ni. These changes were helpful to refine the microstructure and weaken the misorientation. The mechanical test showed that the self-propagation high-temperature synthesis with hot extrusion improved the mechanical properties of the Ni3Al alloy significantly. The addition of B and Cr in Ni3Al alloy increased the mechanical properties further, but the compressive strength of the alloy was still lower than that synthesized by combustion. Finally, the self-propagation high-temperature synthesis with hot extrusion was a good method to prepare Ni3Al alloy from powder.

Influence of Al-Content on the Microstructure and Mechanical Properties in ZrAlN Coatings

2014 ◽  
Vol 1004-1005 ◽  
pp. 778-783 ◽  
Author(s):  
Xiao Ying Zhu ◽  
Jun Du ◽  
Gui Min Liu ◽  
Xiao Hui Zheng
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Phase Structure ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Two Phase ◽  
Al Content ◽  
Microstructure And Mechanical Properties ◽  
Transmission Electron ◽  
Indentation Methods

Zirconium aluminum nitride coatings have been deposited onto Ti-6Al-4V substrates by reactive magnetron sputtering in order to investigate the influence of Al-content on the microstructure and mechanical properties. The morphology and microstructure of the coatings were investigated by field emission scanning electron microscopy (SEM), X-ray diffraction (XRD), and transmission electron microscopy (TEM). Nanoindentation and Vicker’s indentation methods were employed to measure the hardness and toughness of the coatings, respectively. The results show that a structure of single cubic phase with twinning is formed at Al content of x ≤ 0.23, and a two-phase structure of hexagonal and cubic phase is formed at Al content of x ≥ 0.47. Hardness and toughness of the Zr1-xAlxN coatings show similar tendency with the increasing of Al-content. Both of them reach the maximum values at x=0.23 and drop to the minimum values at x=0.47, after that, they slightly increase with the increasing Al-content. The enhanced hardness and toughness achieved at x=0.23 is ascribed not only to single cubic phase structure but also to twinning structure.

scholarly journals Enhancement of the mechanical properties of HDPE mineral nanocomposites by filler particles modulation of the matrix plastic/elastic behavior

2022 ◽  
Vol 11 (1) ◽  
pp. 312-320
Author(s):  
Yousef Murtaja ◽  
Lubomír Lapčík ◽  
Harun Sepetcioglu ◽  
Jakub Vlček ◽  
Barbora Lapčíková ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Performance ◽  
Plant Production ◽  
Elastic Behavior ◽  
Indentation Modulus ◽  
Transmission Electron ◽  
The Matrix ◽  
Poly Ethylene ◽  
Mineral Fillers

Abstract Two different nanosized mineral fillers (nano calcium carbonate and nanoclay) were used in the high density poly(ethylene) (HDPE) composites pilot plant production. Structural and mechanical properties of the prepared composites were examined in this study. The homogenous filler distribution was confirmed in the tested samples by scanning electron microscopy, transmission electron microscopy, and energy dispersive spectroscopy analyses. The fillers’ fortifying effect on polymer composites’ mechanical performance was confirmed as indicated by the increased elastic modulus and indentation modulus. Additionally, the possible modulation of the plastic-elastic mechanical behavior was confirmed by the type of the filler as well as its concentration used in the final composites testing articles.

scholarly journals Investigation of Mechanical Properties of Basalt Particle-Filled SMC Composites

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Kadir Cavdar ◽  
Mahmut Bingol
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Strength Properties ◽  
Reinforced Composites ◽  
Reinforced Composite ◽  
Particle Reinforced Composites ◽  
Moulding Compound ◽  
Glass Fibre Reinforced ◽  
Sheet Moulding Compound ◽  
Scanning Electron

Basalt particles have been investigated as a novel additive for the production of glass fibre reinforced composite using sheet moulding compound (SMC) method. Compared to the CaCO3that are widely used as filler in the SMC composite, the resulting composites exhibit improved mechanical properties. The tensile strength increased by approximately 15%, whereas the flexural strength was enhanced by 8% in SMC composites prepared by basalt particles. Examination of the surface morphology and interfacial debonding of the specimens is also performed via scanning electron microscopy. Superior strength properties are observed in the basalt particle-reinforced composites compared to those with the CaCO3fillers.

Microstructural and Mechanical Properties of Polyester/Nanoclay Nanocomposites: Microstructure-Mixing Strategy Correlation

2011 ◽  
Vol 1312 ◽  
Author(s):  
Hamid Dalir ◽  
Rouhollah D. Farahani ◽  
Vireya Nhim ◽  
Benjamin Samson ◽  
Martin Lévesque ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Strain ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Roll Mill ◽  
The Matrix ◽  
Polyester Matrix ◽  
Excellent Improvement

ABSTRACTDifferent nanoclay mixing strategies using a three-roll mill and ultrasonication is proposed to obtain the desired polyester/nanoclay dispersion, intercalation, and exfoliation. The dispersion states of the modified nanoclay in polymer with 2, 4 and 6 wt% loading were characterized with X-ray diffraction, scanning electron microscopy (SEM), and low and high magnification transmission electron microscopy (TEM). The mechanical properties of the clay-reinforced polyester nanocomposites were a function of the nature and the content of the clay in the matrix. The nanocomposite containing 4 wt% modified Cloisite® 15A exhibits excellent improvement in modulus (by ~51%) and tensile strength (by ~12%) with a decrease in fracture strain (by ~26%) and fracture energy (by ~17%). These mechanical characteristic changes can be attributed to the dispersion, intercalation, and exfoliation of the nanoclays inside the polyester matrix.

Molybdenum Silicides as a Bonding Phase in Diamond Composites

2005 ◽  
Vol 498-499 ◽  
pp. 587-593
Author(s):  
L. Jaworska ◽  
Jerzy Morgiel ◽  
Ludosław Stobierski ◽  
Jerzy Lis ◽  
B. Krolicka ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Thermal Exposure ◽  
The Self ◽  
X Ray ◽  
Transmission Electron ◽  
Molybdenum Silicides ◽  
Bonding Phase ◽  
Type Apparatus ◽  
Shs Method

Molybdenum silicides were obtained by the self-propagating synthesis (SHS) method. Diamond composites containing 30 mass% of MoSi2 or Mo5Si3 bonding phase had been prepared using HT-HP Bridgman type apparatus. Sintering of the diamond composites were carried out at 2073±50 K and 8±0.2 GPa. The interactions in diamond-silicide composites were studied by means of X-ray diffractometry and transmission electron microscopy (TEM). Results of both mechanical properties and thermal resistance measurements are reported. Hardness HV1 for the composite with the predominantly MoSi2 bonding phase was found to be around 42 GPa. After heat treatment in 1200 °C for 30 min. in vacuum HV1 decreases to 29 GPa. In the second composite containing the Mo5Si3 bonding phase the HV1 of 28.0 GPa after thermal exposure changes to 21.0 GPa.

Sign in / Sign up

Export Citation Format

Share Document