scholarly journals Investigations on Residual Stresses within Hot-Bulk-Formed Components Using Process Simulation and the Contour Method

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 566
Author(s):  
Bernd-Arno Behrens ◽  
Jens Gibmeier ◽  
Kai Brunotte ◽  
Hendrik Wester ◽  
Nicola Simon ◽  
...  
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Process Simulation ◽  
Hot Forming ◽  
Contour Method ◽  
Stress Profile ◽  
X Ray Diffraction ◽  
Forming Process ◽  
Near Surface ◽  
X Ray

Residual stresses resulting from hot-forming processes represent an important aspect of a component’s performance and service life. Considering the whole process chain of hot forming, the integrated heat treatment provided by a defined temperature profile during cooling offers a great potential for the targeted adjustment of the desired residual stress state. Finite element (FE) simulation is a powerful tool for virtual process design aimed at generating a beneficial residual stress profile. The validation of these FE models is typically carried out on the basis of individual surface points, as these are accessible through methods like X-ray diffraction, hole-drilling, or the nanoindentation method. However, especially in bulk forming components, it is important to evaluate the quality of the model based on residual stress data from the volume. For these reasons, in this paper, an FE model which was already validated by near surface X-ray diffraction analyses was used to explain the development of residual stresses in a reference hot forming process for different cooling scenarios. Subsequently, the reference process scenarios were experimentally performed, and the resulting residual stress distributions in the cross-section of the bulk specimens were determined by means of the contour method. These data were used to further validate the numerical simulation of the hot forming process, wherein a good agreement between the contour method and process simulation was observed.

Experimental/Modelling Study of Residual Stress in Al/SiCp Bent Bars by Synchrotron XRD and Slitting Eigenstrain Methods

2008 ◽  
Vol 571-572 ◽  
pp. 277-282 ◽  
Author(s):  
Xu Song ◽  
Solène Chardonnet ◽  
Giancarlo Savini ◽  
Shu Yan Zhang ◽  
Willem J.J. Vorster ◽  
...  
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Residual Strain ◽  
Numerical Models ◽  
Front Face ◽  
Stress Profile ◽  
X Ray Diffraction ◽  
Element Analysis ◽  
X Ray ◽  
Residual Stress Profile

The aim of the study presented here was to evaluate the residual stresses present in a bar of aluminium alloy 2124-T1 matrix composite (MMC) reinforced with 25vol% particulate silicon carbide (SiCp) using X-ray diffraction and 3D profilometry (curvature measurement using Mitutoyo/Renishaw coordinate measurement machine) and comparing these results with numerical models of residual strain and stress profiles obtained by a simple inelastic bending model and Finite Element Analysis (FEA). The residual strain distribution was introduced into the test piece by plastic deformation in the 4-point bending configuration. At the first stage of this study the elasticplastic behaviour of the MMC was characterized under static and cyclic loading to obtain the material parameters, hardening proprieties and cyclic hysteresis loops. Subsequently, synchrotron Xray diffraction and CMM curvature measurements were performed to deduce the residual stress profile in the central section of the bar. The experimental data obtained from these measurements were used in the inelastic bending and FEA simulations. The specimens were then subjected to incremental slitting using EDM (electric discharge machining) with continuous back and front face strain gauge monitoring. The X-ray diffraction and incremental slitting results were then analysed using direct and inverse eigenstrain methods. Residual stresses plots obtained by different methods show good agreement with each other.

Micro-slotting technique for reliable measurement of sub-surface residual stress in Ti-6Al-4V

2018 ◽  
Vol 53 (6) ◽  
pp. 389-399 ◽  
Author(s):  
Elizabeth Burns ◽  
Joseph Newkirk ◽  
James Castle
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Image Correlation ◽  
X Ray Diffraction ◽  
Surface Residual Stress ◽  
Near Surface ◽  
X Ray ◽  
Measurement Volume ◽  
Surface Residual Stresses

Micro-slotting, a relaxation residual stress measurement technique, has recently been shown to be an effective method for measuring local residual stresses in a variety of materials. The micro-slotting method relies on a scanning electron microscope–focused ion beam system for milling and imaging, digital image correlation software to track displacements due to residual stress relaxation after milling, and finite element analysis for displacement–stress correlation and calculation of the original stress state in the imaged region. The high spatial resolution of the micro-slotting method makes it a promising technique for obtaining near-surface residual stress data in Ti-6Al-4V components for input into fatigue life models and crack growth simulations. However, use of the micro-slotting method on this alloy has yet to be evaluated against more established measurement techniques. In this study, spatially resolved sub-surface residual stress measurements were obtained on shot peened and low-stress surface-machined Ti-6Al-4V planar coupons using the micro-slotting method and were compared to measurements obtained using the conventional X-ray diffraction depth profiling technique. The sub-surface measurements were in good agreement for the shot peened sample. Observed differences in the measured near-surface residual stresses on the surface-machined sample were attributed to the larger measurement volume of the X-ray diffraction method, suggesting that the micron-sized measurement volume of the micro-slotting method may be more suitable for capturing shallow stress profiles and steep stress gradients. Prior to performing the micro-slotting measurements, finite element modeled displacements were used to verify the measurement procedure and to address uncertainties in the milled slot geometries. The results of this study demonstrated the validity of the micro-slotting procedure and established the technique as a reliable method for measuring sub-surface residual stresses in Ti-6Al-4V.

scholarly journals Statistical analysis of the reproducibility of residual stress measurements in cold extruded parts

2021 ◽  
Author(s):  
Fabian Jaeger ◽  
Alessandro Franceschi ◽  
Holger Hoche ◽  
Peter Groche ◽  
Matthias Oechsner
Keyword(s):  
Residual Stress ◽  
Statistical Analysis ◽  
Stress Measurement ◽  
Industrial Applications ◽  
Cold Extrusion ◽  
X Ray Diffraction ◽  
Forming Process ◽  
X Ray ◽  
Stress States ◽  
Key Aspects

AbstractCold extruded components are characterized by residual stresses, which originate from the experienced manufacturing process. For industrial applications, reproducibility and homogeneity of the final components are key aspects for an optimized quality control. Although striving to obtain identical deformation and surface conditions, fluctuation in the manufacturing parameters and contact shear conditions during the forming process may lead to variations of the spatial residual stress distribution in the final product. This could lead to a dependency of the residual stress measurement results on the relative axial and circumferential position on the sample. An attempt to examine this problem is made by the employment of design of experiments (DoE) methods. A statistical analysis of the residual stress results generated through X-Ray diffraction is performed. Additionally, the ability of cold extrusion processes to generate uniform stress states is analyzed on specimens of austenitic stainless steel 1.4404 and possible correlations with the pre-deformed condition are statistically examined. Moreover, the influence of the coating, consisting of oxalate and a MoS2 based lubricant, on the X-Ray diffraction measurements of the surface is investigated.

scholarly journals Cross-Sectional Mapping of Residual Stresses by Measuring the Surface Contour After a Cut

2000 ◽  
Vol 123 (2) ◽  
pp. 162-168 ◽  
Author(s):  
M. B. Prime
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Superposition Principle ◽  
New Method ◽  
Contour Method ◽  
Stress Profile ◽  
Relaxation Methods ◽  
Cross Sectional ◽  
Residual Stress Profile

A powerful new method for residual stress measurement is presented. A part is cut in two, and the contour, or profile, of the resulting new surface is measured to determine the displacements caused by release of the residual stresses. Analytically, for example using a finite element model, the opposite of the measured contour is applied to the surface as a displacement boundary condition. By Bueckner’s superposition principle, this calculation gives the original residual stresses normal to the plane of the cut. This “contour method” is more powerful than other relaxation methods because it can determine an arbitrary cross-sectional area map of residual stress, yet more simple because the stresses can be determined directly from the data without a tedious inversion technique. The new method is verified with a numerical simulation, then experimentally validated on a steel beam with a known residual stress profile.

Influence of deposition parameters on the residual stresses of WC-Wo sputtered thin films

MRS Advances ◽  
2020 ◽  
Vol 5 (23-24) ◽  
pp. 1215-1223
Author(s):  
R.R. Phiri ◽  
O.P. Oladijo ◽  
E.T. Akinlabi
Keyword(s):  
Thin Films ◽  
Residual Stress ◽  
Residual Stresses ◽  
Substrate Surface ◽  
Tribological Performance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Compressive Stresses ◽  
Deposition Parameters ◽  
Cobalt Thin Films

AbstractControl and manipulation of residual stresses in thin films is a key for attaining coatings with high mechanical and tribological performance. It is therefore imperative to have reliable residual stress measurements methods to further understand the dynamics involved. The sin2ψ method of X-ray diffraction was used to investigate the residual stresses on the tungsten carbide cobalt thin films deposited on a mild steel surface to understand the how the deposition parameters influence the generation of residual stresses within the substrate surface. X-ray spectra of the surface revealed an amorphous phase of the thin film therefore the stress measured was of the substrate surface and the effects of sputtering parameters on residual stress were analysed. Compressive stresses were identified within all samples studied. The results reveal that as the sputtering parameters are varied, the residual stresses also change. Optimum deposition parameters in terms of residual stresses were suggested.

X-Ray Diffraction Analysis of Steel with Oxidised Surface Layer

2016 ◽  
Vol 368 ◽  
pp. 99-102
Author(s):  
Lukáš Zuzánek ◽  
Ondřej Řidký ◽  
Nikolaj Ganev ◽  
Kamil Kolařík
Keyword(s):  
Residual Stress ◽  
Surface Layer ◽  
Residual Stresses ◽  
Diffraction Analysis ◽  
Oxide Surface ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrolytic Polishing ◽  
Small Depth

The basic principle of the X-ray diffraction analysis is based on the determination of components of residual stresses. They are determined on the basis of the change in the distance between atomic planes. The method is limited by a relatively small depth in which the X-ray beam penetrates into the analysed materials. For determination of residual stresses in the surface layer the X-ray diffraction and electrolytic polishing has to be combined. The article is deals with the determination of residual stress and real material structure of a laser-welded steel sample with an oxide surface layer. This surface layer is created during the rolling and it prevents the material from its corrosion. Before the X-ray diffraction analysis can be performed, this surface layer has to be removed. This surface layer cannot be removed with the help of electrolytic polishing and, therefore, it has to be removed mechanically. This mechanical procedure creates “technological” residual stress in the surface layer. This additional residual stress is removed by the electrolytic polishing in the depth between 20 and 80 μm. Finally, the real structure and residual stresses can be determined by using the X-ray diffraction techniques.

Residual Stress Depth-Profiling in Shot-Peened Al Alloy Components Subjected to Fatigue Testing

2010 ◽  
Vol 638-642 ◽  
pp. 2464-2469 ◽  
Author(s):  
Cristy Leonor Azanza Ricardo ◽  
G. Degan ◽  
M. Bandini ◽  
Paolo Scardi
Keyword(s):  
Residual Stress ◽  
Fatigue Testing ◽  
Depth Profiling ◽  
Cyclic Stress ◽  
Al Alloy ◽  
Stress Profile ◽  
X Ray Diffraction ◽  
X Ray ◽  
Residual Stress Profile ◽  
Number Of Cycles

The residual stress profile in a shot-peened Al alloy component was studied by a recently proposed method based on the known procedure of progressive thinning and X-ray Diffraction measurements. The effect the cyclic stress on the fatigue life was studied in detail, showing the correlation between nominal load and residual stress relaxation. Besides showing the expected decrease of compressive stress with the load and number of cycles, the present work highlights the importance of changes in the through-the-thickness residual stress distribution.

Measuring residual stresses in stainless steel—recent experiences within a VAMAS exercise

2009 ◽  
Vol 24 (S1) ◽  
pp. S41-S44 ◽  
Author(s):  
A. T. Fry ◽  
J. D. Lord
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Residual Stresses ◽  
Best Practice ◽  
Test Procedure ◽  
Industrial Plant ◽  
X Ray Diffraction ◽  
X Ray ◽  
Industrial Sectors

Residual stresses impact on a wide variety of industrial sectors including the automotive, power generation, industrial plant, construction, aerospace, railway and transport industries, and a range of materials manufacturers and processing companies. The X-ray diffraction (XRD) technique is one of the most popular methods for measuring residual stress (Kandil et al., 2001) used routinely in quality control and materials characterization for validating models and design. The VAMAS TWA20 Project 3 activity on the “Measurement of Residual Stresses by X-ray Diffraction” was initiated by NPL in 2005 to examine various aspects of the XRD test procedure in support of work aimed at developing an international standard in this area. The purpose of this project was to examine and reduce some of the sources of scatter and uncertainty in the measurement of residual stress by X-ray diffraction on metallic materials, through an international intercomparison and validation exercise. One of the major issues the intercomparison highlighted was the problem associated with measuring residual stresses in austenitic stainless steel. The following paper describes this intercomparison, reviews the results of the exercise and details additional work looking at developing best practice for measuring residual stresses in austenitic stainless steel, for which X-ray measurements are somewhat unreliable and problematic.

Wheel Rim Axial Residual Stress and a Proposed Mechanism for Vertical Split Rim Formation

2011 ◽  
Author(s):  
Cameron Lonsdale ◽  
John Oliver
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Axial Stress ◽  
X Ray Diffraction ◽  
X Ray ◽  
Axial Residual Stress ◽  
Railroad Wheels ◽  
Hoop Stresses ◽  
Future Work

Railroad wheels are manufactured with beneficial residual compressive hoop stresses, which are imparted by rim quenching and tempering. Hoop and radial residual stresses for wheels have been studied in detail by various organizations over the years and are relatively well characterized. However axial residual stresses, in the orientation across the rim width from back rim face to front rim face, have not been extensively investigated. This paper describes a failure mode known as a vertical split rim (VSR) and describes efforts to measure the axial residual stresses in, 1) new wheels, 2) service worn wheels and 3) wheels that have failed from VSRs. Initial axial residual stress measurement efforts, using core drilling and x-ray diffraction from the tread surface, are briefly reviewed. Further more extensive work using x-ray diffraction to measure axial residual stress on radial wheel slices is described and data are presented, focusing on differences between the three wheel types. The concept of Axial Stress Amplification (ASA) is outlined, and the relationship of axial residual stress to VSRs is discussed. A proposed mechanism for VSR formation is described. Future work, with a goal of reducing or eliminating VSRs in service, is considered.

Sign in / Sign up

Export Citation Format

Share Document