scholarly journals Influence of Al Additions on the Microstructure and Mechanical Properties of a C and Si-Free High-Mn Steel

Metals ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 352
Author(s):  
Lucas Otani ◽  
André Vidilli ◽  
Francisco Coury ◽  
Claudio Kiminami ◽  
Walter Botta ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Dislocation Cell ◽  
Spray Forming ◽  
Specific Strength ◽  
Al Content ◽  
Fine Grain ◽  
Work Hardening Rate ◽  
Cold Rolling And Annealing ◽  
Al Additions

The lightweight Fe–Mn–Al–C steels have drawn considerable attention from the literature due to their outstanding combination of high ductility and specific strength. Although the mechanical behavior of such steels has been extensively studied, the effect of Al when no C and Si are added has not been investigated in detail. For this reason, the main objective of this work was to study the microstructural evolution and mechanical behavior of carbon and silicon-free high-Mn steels with different aluminum contents. Alloys with 0, 2.5, and 5 wt. % Al were processed by spray forming to ensure high homogeneity and a fully austenitic microstructure. Cold rolling and annealing were performed to obtain a fine grain-sized material. The mechanical properties were similar regardless of the Al content, especially the work hardening rate. Deformation twinning and strain-induced phase transformation were not observed for any of the compositions. Additionally, a dislocation cell-like structure was observed for all of the alloys indicating that the Al additions did not change considerably the dislocation behavior, even though it considerably changed the estimated Stacking Fault Energy (SFE) value for all the alloys studied in this work.

Effects of bottom plate in friction stir welding of AA6061-T6

2020 ◽  
Vol 118 (1) ◽  
pp. 108
Author(s):  
M.A. Vinayagamoorthi ◽  
M. Prince ◽  
S. Balasubramanian
Keyword(s):  
Mechanical Properties ◽  
Axial Load ◽  
Weld Zone ◽  
Welding Process ◽  
Bottom Plate ◽  
Welding Parameters ◽  
Nugget Zone ◽  
Friction Stir ◽  
Weld Joints ◽  
Fine Grain

The effects of 40 mm width bottom plates on the microstructural modifications and the mechanical properties of a 6 mm thick FSW AA6061-T6 joint have been investigated. The bottom plates are placed partially at the weld zone to absorb and dissipate heat during the welding process. An axial load of 5 to 7 kN, a rotational speed of 500 rpm, and a welding speed of 50 mm/min are employed as welding parameters. The size of the nugget zone (NZ) and heat-affected zone (HAZ) in the weld joints obtained from AISI 1040 steel bottom plate is more significant than that of weld joints obtained using copper bottom plate due to lower thermal conductivity of steel. Also, the weld joints obtained using copper bottom plate have fine grain microstructure due to the dynamic recrystallization. The friction stir welded joints obtained with copper bottom plate have exhibited higher ductility of 8.9% and higher tensile strength of 172 MPa as compared to the joints obtained using a steel bottom plate.

MODELISATION DE L'INFLUENCE DU TRAITEMENT THERMIQUE SUR LES PROPRIETES MECANIQUES DES ALLIAGES ALUMINIUM-CUIVRE (Al-Cu)

2015 ◽  
Vol 10 (2) ◽  
pp. 2753-2761
Author(s):  
Saad El Madani ◽  
S. ELHAMZI ◽  
A. IBNLFASSI ◽  
L. ZERROUK ◽  
O. BEN LENDA ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Solidification Process ◽  
Traitement Thermique ◽  
Homogenization Process ◽  
Fundamental Reason ◽  
Segregation Phenomenon ◽  
Proprietes Mecaniques ◽  
Cooling Velocity ◽  
Copper Effect

In order to master and improve the quality and properties of the final products, the major industrial challenge lies in the possibility of controlling the morphology, size of microstructures that reside within the molded pieces, as well as their defects; this is the fundamental reason according to which we are more and more interested in mastering the growth and germination of such alloys, as well as the developing structures, at the time of solidification process. The modeling reveals as a valuable aid in the mastery of the formation of such heterogeneousness: segregation cells that are incompatible with industrial requirements.   The whole work focuses upon the modeling of the segregation phenomenon of the four hypoeutectic alloys, Al1%Cu, Al2%Cu, Al3%Cu et Al4%Cu, as well as the copper effect upon certain mechanical properties of aluminum. Usually, the microstructure and mechanical behavior of such alloys as Al-Cu are directly influenced by some parameters such as composition, cooling velocity and homogenization process.

scholarly journals Biological Applications of Severely Plastically Deformed Nano-Grained Medical Devices: A Review

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 748
Author(s):  
Katayoon Kalantari ◽  
Bahram Saleh ◽  
Thomas J. Webster
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Bacterial Colonization ◽  
Antibiotic Use ◽  
Bone Cell ◽  
Corrosion Properties ◽  
Biomedical Implant ◽  
Specific Strength ◽  
Biological Functionality ◽  
Bone Cell Proliferation

Metallic materials are widely used for fabricating medical implants due to their high specific strength, biocompatibility, good corrosion properties, and fatigue resistance. Recently, titanium (Ti) and its alloys, as well as stainless steel (SS), have attracted attention from researchers because of their biocompatibility properties within the human body; however, improvements in mechanical properties while keeping other beneficial properties unchanged are still required. Severe plastic deformation (SPD) is a unique process for fabricating an ultra-fine-grained (UFG) metal with micrometer- to nanometer-level grain structures. SPD methods can substantially refine grain size and represent a promising strategy for improving biological functionality and mechanical properties. This present review paper provides an overview of different SPD techniques developed to create nano-/ultra-fine-grain-structured Ti and stainless steel for improved biomedical implant applications. Furthermore, studies will be covered that have used SPD techniques to improve bone cell proliferation and function while decreasing bacterial colonization when cultured on such nano-grained metals (without resorting to antibiotic use).

scholarly journals Experimental and Numerical Evaluation of Mechanical Properties of 3D-Printed Stainless Steel 316L Lattice Structures

2021 ◽  
Author(s):  
M. Carraturo ◽  
G. Alaimo ◽  
S. Marconi ◽  
E. Negrello ◽  
E. Sgambitterra ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Mechanical Behavior ◽  
Numerical Simulations ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Lattice Structures ◽  
Stainless Steel 316L ◽  
Research Attention ◽  
Octet Truss

AbstractAdditive manufacturing (AM), and in particular selective laser melting (SLM) technology, allows to produce structural components made of lattice structures. These kinds of structures have received a lot of research attention over recent years due to their capacity to generate easy-to-manufacture and lightweight components with enhanced mechanical properties. Despite a large amount of work available in the literature, the prediction of the mechanical behavior of lattice structures is still an open issue for researchers. Numerical simulations can help to better understand the mechanical behavior of such a kind of structure without undergoing long and expensive experimental campaigns. In this work, we compare numerical and experimental results of a uniaxial tensile test for stainless steel 316L octet-truss lattice specimen. Numerical simulations are based on both the nominal as-designed geometry and the as-build geometry obtained through the analysis of µ-CT images. We find that the use of the as-build geometry is fundamental for an accurate prediction of the mechanical behavior of lattice structures.

scholarly journals Effect of Sm Doping on the Microstructure, Mechanical Properties and Shape Memory Effect of Cu-13.0Al-4.0Ni Alloy

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4007
Author(s):  
Qimeng Zhang ◽  
Bo Cui ◽  
Bin Sun ◽  
Xin Zhang ◽  
Zhizhong Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Strengthening Effect ◽  
Face Centered Cubic ◽  
Compressive Fracture ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Face Centered

The effects of rare earth element Sm on the microstructure, mechanical properties, and shape memory effect of the high temperature shape memory alloy, Cu-13.0Al-4.0Ni-xSm (x = 0, 0.2 and 0.5) (wt.%), are studied in this work. The results show that the Sm addition reduces the grain size of the Cu-13.0Al-4.0Ni alloy from millimeters to hundreds of microns. The microstructure of the Cu-13.0Al-4.0Ni-xSm alloys are composed of 18R and a face-centered cubic Sm-rich phase at room temperature. In addition, because the addition of the Sm element enhances the fine-grain strengthening effect, the mechanical properties and the shape memory effect of the Cu-13.0Al-4.0Ni alloy were greatly improved. When x = 0.5, the compressive fracture stress and the compressive fracture strain increased from 580 MPa, 10.5% to 1021 MPa, 14.8%, respectively. When the pre-strain is 10%, a reversible strain of 6.3% can be obtained for the Cu-13.0Al-4.0Ni-0.2Sm alloy.

scholarly journals Decoupling of Mechanical and Transport Properties in Organogels via Solvent Variation

Gels ◽  
2021 ◽  
Vol 7 (2) ◽  
pp. 61
Author(s):  
Kenneth P. Mineart ◽  
Cameron Hong ◽  
Lucas A. Rankin
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Transdermal Drug Delivery ◽  
Triblock Copolymer ◽  
Polymer Concentration ◽  
Mineral Oil ◽  
Solute Diffusion ◽  
Oil Viscosity ◽  
Chain Entanglement ◽  
Mineral Oils

Organogels have recently been considered as materials for transdermal drug delivery media, wherein their transport and mechanical properties are among the most important considerations. Transport through organogels has only recently been investigated and findings highlight an inextricable link between gels’ transport and mechanical properties based upon the formulated polymer concentration. Here, organogels composed of styrenic triblock copolymer and different aliphatic mineral oils, each with a unique dynamic viscosity, are characterized in terms of their quasi-static uniaxial mechanical behavior and the internal diffusion of two unique solute penetrants. Mechanical testing results indicate that variation of mineral oil viscosity does not affect gel mechanical behavior. This likely stems from negligible changes in the interactions between mineral oils and the block copolymer, which leads to consistent crosslinked network structure and chain entanglement (at a fixed polymer concentration). Conversely, results from diffusion experiments highlight that two penetrants—oleic acid (OA) and aggregated aerosol-OT (AOT)—diffuse through gels at a rate inversely proportional to mineral oil viscosity. The inverse dependence is theoretically supported by the hydrodynamic model of solute diffusion through gels. Collectively, our results show that organogel solvent variation can be used as a design parameter to tailor solute transport through gels while maintaining fixed mechanical properties.

scholarly journals Understanding the Barrier and Mechanical Behavior of Different Nanofillers in Chitosan Films for Food Packaging

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 721 ◽  
Author(s):  
João Pires ◽  
Camila Damásio de Paula ◽  
Victor Gomes Lauriano Souza ◽  
Ana Luísa Fernando ◽  
Isabel Coelhoso
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Food Packaging ◽  
Scientific Research ◽  
Barrier Properties ◽  
Plastic Pollution ◽  
Functional Attributes ◽  
Chitosan Films ◽  
Commercial Applications ◽  
Innovative Techniques

The continuous petroleum-based plastics manufacturing generates disposal issues, spreading the problem of plastic pollution and its rise in the environment. Recently, innovative techniques and scientific research promoted biopolymers as the primary alternative for traditional plastics, raising and expanding global bioplastic production. Due to its unmatched biological and functional attributes, chitosan (Ch) has been substantially explored and employed as a biopolymeric matrix. Nevertheless, the hydrophilicity and the weak mechanical properties associated with this biopolymer represent a significant intrinsic restriction to its implementation into some commercial applications, namely, in food packaging industries. Distinct methodologies have been utilized to upgrade the mechanical and barrier properties of Ch, such as using organic or inorganic nanofillers, crosslinkers, or blends with other polymers. This review intends to analyze the most recent works that combine the action of different nanoparticle types with Ch films to reinforce their mechanical and barrier properties.

Sign in / Sign up

Export Citation Format

Share Document