scholarly journals A Comparison Study on the Strengthening and Toughening Mechanism between Cu-Bearing Age-Hardening Steel and NiCrMoV Steel

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4276
Author(s):  
Xiaobing Luo ◽  
Chongchen Xiang ◽  
Feng Chai ◽  
Zijian Wang ◽  
Zhengyan Zhang ◽  
...  
Keyword(s):  
Strength Loss ◽  
Dislocation Motion ◽  
Age Hardening ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Comparison Study ◽  
Toughening Mechanism ◽  
Transmission Electron ◽  
Heat Treated ◽  
Nicrmov Steel

Cu-bearing age-hardening steel has significant potential in shipbuilding applications due to its excellent weldability as compared to conventional NiCrMoV steel. Not much research has been carried out to analyze the differences in the mechanisms of strength and toughness between Cu-bearing age-hardening and NiCrMoV steel. Both steels were heat treated under the same conditions: they were austenized at 900 °C and then quenched to room temperature, followed by tempering at 630 °C for 2 h. The uniaxial tensile test reveals that the Cu-bearing age-hardening steel exhibits relatively lower strength but larger plasticity than NiCrMoV steel. The lower contents of Carbon and other alloying elements is one of possible reasons for these differences in mechanical properties. Transmission Electron Microscope observations show that two types of precipitates, Cr carbides and Cu-rich particles, exist in tempered Cu-bearing age-hardening steel. Cu-rich particles with sizes of 20–40 nm can inhibit the dislocation motion during deformation, which then results in dislocation pile ups and multiplication; this makes up the strength loss of Cu-bearing age-hardening steel and simultaneously improves its plasticity.

The effect of small additions of Cu on precipitation in Al-Mg-Si alloys

1990 ◽  
Vol 48 (2) ◽  
pp. 442-443
Author(s):  
M. Tamizifar ◽  
G. Cliff ◽  
R.W. Devenish ◽  
G.W. Lorimer
Keyword(s):  
Electron Microscopy ◽  
Analytical Electron Microscopy ◽  
Scanning Transmission Electron Microscope ◽  
Argon Atmosphere ◽  
Age Hardening ◽  
X Ray ◽  
Transmission Electron ◽  
Heat Treated ◽  
Analytical Electron ◽  
Scanning Transmission

Small additions of copper, <1 wt%, have a pronounced effect on the ageing response of Al-Mg-Si alloys. The object of the present investigation was to study the effect of additions of copper up to 0.5 wt% on the ageing response of a series of Al-Mg-Si alloys and to use high resolution analytical electron microscopy to determine the composition of the age hardening precipitates.The composition of the alloys investigated is given in Table 1. The alloys were heat treated in an argon atmosphere for 30m, water quenched and immediately aged either at 180°C for 15 h or given a duplex treatment of 180°C for 15 h followed by 350°C for 2 h2. The double-ageing treatment was similar to that carried out by Dumolt et al. Analyses of the precipitation were carried out with a HB 501 Scanning Transmission Electron Microscope. X-ray peak integrals were converted into weight fractions using the ratio technique of Cliff and Lorimer.

scholarly journals Post-Heat Treatment and Mechanical Assessment of Polyvinyl Alcohol Nanofiber Sheet Fabricated by Electrospinning Technique

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Mahir Es-saheb ◽  
Ahmed Elzatahry
Keyword(s):  
Polyvinyl Alcohol ◽  
Strain Rate ◽  
Young Modulus ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Gravimetric Analysis ◽  
Test Results ◽  
Electrospinning Technique ◽  
Transmission Electron ◽  
Heat Treated

Polyvinyl alcohol (PVA) sheets based nanofibers were produced by electrospinning technique. Postheat treatment of the produced PVA sheets with temperatures both below and above Tg to improve the mechanical properties of this material is conducted. The morphology, microstructures, and thermal degradation of the nanofibers sheets produced were investigated using scanning electron microscopy (SEM), transmission electron microscope (TEM), and thermal gravimetric analysis (TGA). Produced nanofibers are compact, and entangled with each other, with diameters from around 150 to 210. Some mechanical characteristics of the successfully produced PVA sheets, and heat-treated, are then conducted and assessed employing uniaxial tensile tests at different speeds ranging from 1 mm/min to 100 mm/min. The tensile test results obtained show that the PVA sheets are strain rate sensitive with increasing strength as the speed (i.e., strain rate) increases. The yield tensile stress ranges from 2.411 to 6.981 MPa, the ductility (i.e., elongation percent) from∼21 to 60%, and Young modulus ranges from 103 to 0.137 KPa. However, for heat-treated samples, it is found that the yield strength increases almost by∼35–40% more than the values of untreated cases with values reaching up to about 3.627–9.63 MPa.

Direct Observation of Crystalline Ordering In Naturally Graphitized Carbon Produced by Low Grade Metamorphism

1977 ◽  
Vol 35 ◽  
pp. 162-163
Author(s):  
Thomas R. McKee ◽  
Peter R. Buseck
Keyword(s):  
Crystallite Size ◽  
Sedimentary Rocks ◽  
Carbonaceous Material ◽  
Low Grade ◽  
X Ray ◽  
Graphitized Carbon ◽  
Transmission Electron ◽  
Heat Treated ◽  
Commercial Carbon ◽  
Metamorphic Zone

Sediments commonly contain organic material which appears as refractory carbonaceous material in metamorphosed sedimentary rocks. Grew and others have shown that relative carbon content, crystallite size, X-ray crystallinity and development of well-ordered graphite crystal structure of the carbonaceous material increases with increasing metamorphic grade. The graphitization process is irreversible and appears to be continous from the amorphous to the completely graphitized stage. The most dramatic chemical and crystallographic changes take place within the chlorite metamorphic zone.The detailed X-ray investigation of crystallite size and crystalline ordering is complex and can best be investigated by other means such as high resolution transmission electron microscopy (HRTEM). The natural graphitization series is similar to that for heat-treated commercial carbon blacks, which have been successfully studied by HRTEM (Ban and others).

Precipitation in Al-Li-Cu Alloys

1981 ◽  
Vol 39 ◽  
pp. 44-45
Author(s):  
J. E. O'Neal ◽  
K. K. Sankaran
Keyword(s):  
Electron Microscopy ◽  
Age Hardening ◽  
Precipitation Behavior ◽  
Zone Formation ◽  
Specific Strength ◽  
Hardening Behavior ◽  
Cu Alloys ◽  
High Specific Strength ◽  
Transmission Electron ◽  
Structural Applications

Al-Li-Cu alloys combine high specific strength and high specific modulus and are potential candidates for aircraft structural applications. As part of an effort to optimize Al-Li-Cu alloys for specific applications, precipitation in these alloys was studied for a range of compositions, and the mechanical behavior was correlated with the microstructures.Alloys with nominal compositions of Al-4Cu-2Li-0.2Zr, Al-2.5Cu-2.5Li-0.2Zr, and Al-l.5Cu-2.5Li-0.5Mn were argon-atomized into powder at solidification rates ≈ 103°C/s. Powders were consolidated into bar stock by vacuum pressing and extruding at 400°C. Alloy specimens were solution annealed at 530°C and aged at temperatures up to 250°C, and the resultant precipitation was studied by transmission electron microscopy (TEM).The low-temperature (≲100°C) precipitation behavior of the Al-4Cu-2Li-0.2Zr alloy is a combination of the separate precipitation behaviors of Al-Cu and Al-Li alloys. The age-hardening behavior at these temperatures is characteristic of Guinier-Preston (GP) zone formation, with additional strengthening resulting from the coherent precipitation of δ’ (Al3Li, Ll2 structure), the presence of which is revealed by the selected-area diffraction pattern (SADP) shown in Figure la.

scholarly journals Biomechanical-Structural Correlation of Chordae tendineae in Animal Models: A Pilot Study

Animals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1678
Author(s):  
Justyn Gach ◽  
Izabela Janus ◽  
Agnieszka Mackiewicz ◽  
Tomasz Klekiel ◽  
Agnieszka Noszczyk-Nowak
Keyword(s):  
Mitral Valve ◽  
Complex Structure ◽  
Future Research ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Histopathological Analysis ◽  
Papillary Muscles ◽  
Chordae Tendineae ◽  
Structural Correlation ◽  
Ring Valve

The mitral valve apparatus is a complex structure consisting of the mitral ring, valve leaflets, papillary muscles and chordae tendineae (CT). The latter are mainly responsible for the mechanical functions of the valve. Our study included investigations of the biomechanical and structural properties of CT collected from canine and porcine hearts, as there are no studies about these properties of canine CT. We performed a static uniaxial tensile test on CT samples and a histopathological analysis in order to examine their microstructure. The results were analyzed to clarify whether the changes in mechanical persistence of chordae tendineae are combined with the alterations in their structure. This study offers clinical insight for future research, allowing for an understanding of the process of chordae tendineae rupture that happens during degenerative mitral valve disease—the most common heart disease in dogs.

scholarly journals Experimental and Numerical Evaluation of Mechanical Properties of 3D-Printed Stainless Steel 316L Lattice Structures

2021 ◽  
Author(s):  
M. Carraturo ◽  
G. Alaimo ◽  
S. Marconi ◽  
E. Negrello ◽  
E. Sgambitterra ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Mechanical Behavior ◽  
Numerical Simulations ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Lattice Structures ◽  
Stainless Steel 316L ◽  
Research Attention ◽  
Octet Truss

AbstractAdditive manufacturing (AM), and in particular selective laser melting (SLM) technology, allows to produce structural components made of lattice structures. These kinds of structures have received a lot of research attention over recent years due to their capacity to generate easy-to-manufacture and lightweight components with enhanced mechanical properties. Despite a large amount of work available in the literature, the prediction of the mechanical behavior of lattice structures is still an open issue for researchers. Numerical simulations can help to better understand the mechanical behavior of such a kind of structure without undergoing long and expensive experimental campaigns. In this work, we compare numerical and experimental results of a uniaxial tensile test for stainless steel 316L octet-truss lattice specimen. Numerical simulations are based on both the nominal as-designed geometry and the as-build geometry obtained through the analysis of µ-CT images. We find that the use of the as-build geometry is fundamental for an accurate prediction of the mechanical behavior of lattice structures.

scholarly journals Polar poly(n-butyl acrylate)-g-polyacrylonitrile elastomer with high temperature elasticity and healability as flexible electronic substrate

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Yuzhu Zheng ◽  
Deli Xu ◽  
Shiyou Tian ◽  
Manli Li ◽  
Wenwen Wang ◽  
...  
Keyword(s):  
High Temperature ◽  
Graft Copolymer ◽  
Butyl Acrylate ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Self Healing ◽  
Chemical Structures ◽  
Flexible Electronic ◽  
Ag Nanowires ◽  
Cyano Groups

AbstractIn this work, graft copolymer poly (n-butyl acrylate)-g-polyacrylonitrile with poly (n-butyl acrylate) as backbones and polyacrylonitrile as side chains (PnBA-g-PAN) was synthesized by macromonomer method and emulsion polymerization. The macromonomer was synthesized by atom transfer radical polymerization and end-group modification. The chemical structures and thermal properties of macromonomer and graft copolymer were investigated by FTIR, GPC, NMR and TGA, etc. The mechanical properties of graft copolymer elastomer was also measured by uniaxial tensile test. Rheological properties at different temperature and mechanical property demonstrated that graft copolymer elastomer possessed elasticity until 180 oC because of cyclization of cyano groups. Ag nanowires@PnBA-g-PAN composite elastomer was developed, and the resulted material exhibited autonomic healing property on account of segments’ flexibility and dynamic interaction between Ag nanowires (AgNWs) and cyano groups. This is a general method for generation of elastomer with high temperature elasticity and fast self-healing. The composite elastomer has potential application in flexible electronic conductor.

scholarly journals Ability of Constitutive Models to Characterize the Temperature Dependence of Rubber Hyperelasticity and to Predict the Stress-Strain Behavior of Filled Rubber under Different Defor Mation States

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 369
Author(s):  
Xintao Fu ◽  
Zepeng Wang ◽  
Lianxiang Ma
Keyword(s):  
Experimental Data ◽  
Temperature Dependence ◽  
Mechanical Response ◽  
Constitutive Models ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Chain Model ◽  
Stress Strain ◽  
Filled Rubber ◽  
Yeoh Model

In this paper, some representative hyperelastic constitutive models of rubber materials were reviewed from the perspectives of molecular chain network statistical mechanics and continuum mechanics. Based on the advantages of existing models, an improved constitutive model was developed, and the stress–strain relationship was derived. Uniaxial tensile tests were performed on two types of filled tire compounds at different temperatures. The physical phenomena related to rubber deformation were analyzed, and the temperature dependence of the mechanical behavior of filled rubber in a larger deformation range (150% strain) was revealed from multiple angles. Based on the experimental data, the ability of several models to describe the stress–strain mechanical response of carbon black filled compound was studied, and the application limitations of some constitutive models were revealed. Combined with the experimental data, the ability of Yeoh model, Ogden model (n = 3), and improved eight-chain model to characterize the temperature dependence was studied, and the laws of temperature dependence of their parameters were revealed. By fitting the uniaxial tensile test data and comparing it with the Yeoh model, the improved eight-chain model was proved to have a better ability to predict the hyperelastic behavior of rubber materials under different deformation states. Finally, the improved eight-chain model was successfully applied to finite element analysis (FEA) and compared with the experimental data. It was found that the improved eight-chain model can accurately describe the stress–strain characteristics of filled rubber.

scholarly journals Effect of PWHT on the Microstructure and Mechanical Properties of Friction Stir Welded DP780 Steel

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1097
Author(s):  
Umer Masood Chaudry ◽  
Seung-Chang Han ◽  
Fathia Alkelae ◽  
Tea-Sung Jun
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Tensile Elongation ◽  
Image Correlation ◽  
Frictional Heat ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Dp780 Steel

In the present study, the effect of post-weld heat treatment (PWHT) on the microstructure and mechanical properties of friction stir welded (FSW) DP780 steel sheets was investigated. FSW was carried out at a constant tool rotation speed of 400 rpm and different welding speeds (200 mm/min and 400 min/min). A defect free weld was witnessed for both of the welding conditions. The mutual effect of severe plastic deformation and frictional heat generation by pin rotation during the FSW process resulted in grain refinement due to dynamic recrystallization in the stir zone (SZ) and thermo-mechanically affected zone (TMAZ). Lower tensile elongation and higher yield and ultimate tensile strengths were recorded for welded-samples as compared to the base material (BM) DP780 steel. The joints were subsequently annealed at various temperatures at 450–650 °C for 1 h. At higher annealing temperature, the work hardening rate of joints gradually decreased and subsequently failed in the softened heat-affected zone (HAZ) during the uniaxial tensile test. Reduction in yield strength and tensile strength was found in all PWHT conditions, though improvement in elongation was achieved by annealing at 550 °C. The digital image correlation analysis showed that an inhomogeneous strain distribution occurred in the FSWed samples, and the strain was particularly highly localized in the advancing side of interface zone. The nanoindentation measurements covering the FSWed joint were consistent with an increase of the annealing temperature. The various grains size in the BM, TMAZ, and SZ is the main factor monitoring the hardness distribution in these zones and the observed discrepancies in mechanical properties.

scholarly journals Coupled Thermomechanical Response Measurement of Deformation of Nickel-Based Superalloys Using Full-Field Digital Image Correlation and Infrared Thermography

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2163
Author(s):  
Krzysztof Żaba ◽  
Tomasz Trzepieciński ◽  
Sandra Puchlerska ◽  
Piotr Noga ◽  
Maciej Balcerzak
Keyword(s):  
Surface Temperature ◽  
Strain Rate ◽  
Rolling Direction ◽  
Image Correlation ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Response Measurement ◽  
Sheet Rolling ◽  
Inconel Alloys ◽  
The Relationship

The paper is devoted to highlighting the potential application of the quantitative imaging technique through results associated with work hardening, strain rate and heat generated during elastic and plastic deformation. The aim of the research presented in this article is to determine the relationship between deformation in the uniaxial tensile test of samples made of 1-mm-thick nickel-based superalloys and their change in temperature during deformation. The relationship between yield stress and the Taylor–Quinney coefficient and their change with the strain rate were determined. The research material was 1-mm-thick sheets of three grades of Inconel alloys: 625 HX and 718. The Aramis (GOM GmbH, a company of the ZEISS Group) measurement system and high-sensitivity infrared thermal imaging camera were used for the tests. The uniaxial tensile tests were carried out at three different strain rates. A clear tendency to increase the sample temperature with an increase in the strain rate was observed. This conclusion applies to all materials and directions of sample cutting investigated with respect to the sheet-rolling direction. An almost linear correlation was found between the percent strain and the value of the maximum surface temperature of the specimens. The method used is helpful in assessing the extent of homogeneity of the strain and the material effort during its deformation based on the measurement of the surface temperature.

Sign in / Sign up

Export Citation Format

Share Document