scholarly journals Experimental Determination of Mechanical Properties of Waste Tyre Bales Used for Geotechnical Applications

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3310
Author(s):  
Aleksander Duda ◽  
Tomasz Siwowski
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Cyclic Load ◽  
Young's Modulus ◽  
Poisson Ratio ◽  
Friction Angle ◽  
Stiffness Degradation ◽  
Unit Weight ◽  
Average Height ◽  
Waste Tyre

Waste tyre-derived products (TDP) are used in some engineering applications and thereby reduce the potential impact on the environment, for example, as lightweight materials in geotechnical engineering projects. One of TDPs is the baling of whole waste tyres to produce rectilinear, lightweight, permeable bales of high bale-to-bale or bale-to-soil friction. The use of lightweight tyre bales in road construction has the potential to satisfy the demand for low-cost materials exhibiting such a beneficial property. This paper presents a laboratory study on the mechanical properties of tyre bales. The laboratory tests included measurement and evaluation of full-scale tyre bales to determine basic values for the geometry and unit weight, compressibility characteristics of tyre bales, including Young’s modulus and Poisson ratio, shear strength along the tyre–tyre and tyre–soil surfaces, creep and stiffness degradation under cyclic load. The respective test procedures and results of these tests are presented in the paper. The paper provides the mechanical properties of tyre bales required for geotechnical projects, as follows: the unit weight—0.515 Mg/m3, the Young’s modulus—826 kPa, the Poison’s ratio—0.11, the dry tyre–tyre interface: cohesion of 0.03 kPa and friction angle of 46.0°, the wet tyre–soil interface: cohesion 0.77 kPa and a friction angle of 29.6°, creep deformation of 6.1% of the average height of the bale, and no stiffness degradation of tyre bales under cyclic load. These results could be directly applied for the designing and construction of the tyre-baled structures.

scholarly journals Experimental Investigation on Mechanical Properties of In Situ Cemented Paste Backfill Containing Coal Gangue and Fly Ash

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Xinguo Zhang ◽  
Shichuan Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Friction Angle ◽  
Coal Gangue ◽  
Cemented Paste Backfill ◽  
Paste Backfill

Cemented paste backfill containing coal gangue and fly ash (CGFACPB) is an emerging backfill technique for coal mines that allows environmentally hazardous coal gangue and fly ash to be reused in the underground goaf. Meanwhile, CGFACPB can provide an efficient ground support and reduce the surface subsidence. Due to the difference of consolidation environment between the laboratory and the field, the mechanical properties of the cemented paste backfill vary significantly. In this paper, the core specimens were collected from an underground coal mine where the CGFACPB was used for coal mining, and the mechanical properties of the collected specimens were investigated. The cores were obtained from the underground coal mine, and then the standard cylinders or discs were prepared in laboratory. The uniaxial compressive strength (UCS), Young’s modulus, and Poisson’s ratio were determined by the compression tests, and the tensile strength was achieved by the Brazilian test. Then the internal friction angle and cohesion were calculated using the improved Mohr–Coulomb strength criterion. The results showed the development of UCS can be divided into four stages, and the final long-term stable value was about 5.1 MPa. The development of Young’s modulus had similar trend. Young’s modulus had a range from 550 MPa to 750 MPa and the mean value of 675 MPa. Poisson’s ratio gradually increased with the underground curing duration and eventually approached the stable value of 0.18. The failure type of compression samples was mainly single-sided shear failure. The development of tensile strength can be divided into two stages, and the stable value of the tensile strength was about 1.05 MPa. The development of cohesion can be divided into four stages, and the stable value was about 1.75 MPa. The stable value of the internal friction angle was about 25°. This study can provide significant references for not only the long-term stability evaluation of CGFACPB in the field but also the design of optimal recipe of the cemented paste backfill (CPB).

Determination of Mechanical Properties of Thin Film on Silicon Wafer

2003 ◽  
Author(s):  
Enboa Wu ◽  
Albert J. D. Yang ◽  
Ching-An Shao ◽  
C. S. Yen
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Thermal Expansion ◽  
Young’S Modulus ◽  
Silicon Wafer ◽  
Coefficient Of Thermal Expansion ◽  
Young's Modulus ◽  
Poisson Ratio ◽  
Bulk State

Nondestructive determination of Young’s modulus, coefficient of thermal expansion, Poisson ratio, and thickness of a thin film has long been a difficult but important issue as the film of micrometer order thick might behave differently from that in the bulk state. In this paper, we have successfully demonstrated the capability of determining all these four parameters at one time. This novel method includes use of the digital phase-shifting reflection moire´ (DPRM) technique to record the slope of wafer warpage under temperature drop condition. In the experiment, 1-um thick aluminum was sputtered on a 6-in silicon wafer. The convolution relationship between the measured data and the mechanical properties was constructed numerically using the conventional 3D finite element code. The genetic algorithm (GA) was adopted as the searching tool for search of the optimal mechanical properties of the film. It was found that the determined data for Young’s modulus (E), Coefficient of Thermal Expansion (CTE), Poisson ratio (ν), and thickness (h) of the 1.00 um thick aluminum film were 104.2Gpa, 38.0 ppm/°C, 0.38, and 0.98 um, respectively, whereas that in the bulk state were measured to be E=71.4 Gpa, CTE=23.0 ppm/°C, and ν=0.34. The significantly larger values on the Young’s modulus and the coefficient of thermal expansion determined by this method might be attributed to the smaller dislocation density due to the thin dimension and formation of the 5-nm layer of Al2O3 formed on top of the 1-um thick sputtered film. The Young’s Modulus and the Poisson ratio of this nano-scale Al2O3 film were then determined. Their values are consistent with the physical intuition of the microstructure.

scholarly journals Effect of Alloying Elements on the Mechanical Properties of Mo3Si

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 129
Author(s):  
Wei Bi ◽  
Shunping Sun ◽  
Shaoyi Bei ◽  
Yong Jiang
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Poisson Ratio ◽  
Alloying Elements ◽  
Covalent Bonds ◽  
Excellent Thermal Stability ◽  
Nb Doping ◽  
Effect Of Alloying

Molybdenum silicides are attractive high-temperature structural materials because of their excellent thermal stability and outstanding oxidation resistance at high temperatures. First-principles calculations were employed to investigate the effect of alloying elements (Cr, Nb, V, W, Al, Ga, and Ge) on the mechanical properties of Mo3Si. The structural stabilities of doped Mo3Si were calculated, showing that the Pm-3n structure was stable at the investigated low-doping concentration. The calculated elastic constants have also evaluated some essential mechanical properties of doped Mo3Si. Cr- and V-doping decreased the elastic modulus, while Al- and Nb-doping slightly increased the shear and Young’s modulus of Mo3Si. Furthermore, V-, Al- and Nb-doping decreased the B/G and Poisson ratio, suggesting that these elements could form strong covalent bonds, and decrease shear deformation and alloy ductility. Based on the three-dimensional contours and two-dimensional projection of the elastic modulus, Cr- and V-doping exhibited a significant influence on the anisotropy of the shear and Young’s modulus. According to charge density and density of states, the electronic structures of alloyed Mo3Si were further analyzed to reveal the doping effects.

YOUNG’S MODULUS AND POISSON’S RATIO OF MERPAUH, KAPUR AND SESENDUK SPECIES

2016 ◽  
Vol 78 (5-2) ◽  
Author(s):  
Rohana Hassan ◽  
Syed Syazaril Amri Syed Mubarat ◽  
Anizahyati Alisibramulisi
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Poisson Ratio ◽  
Tensile Tests ◽  
Poisson's Ratio ◽  
Stress And Strain ◽  
Timber Species ◽  
Strength Capacity

Young’s Modulus and Poisson’s ratio are the mechanical properties that need to be determined for the production of engineering design or information for the numerical analysis of timber. In this study, Merpauh, Kapur and Sesenduk species were selected. This experimental investigation focuses on the elastic properties of those timber species. The Modulus of Elasticity (MOE) and Poisson’s ratio were determined by means of tensile tests. In addition, Modulus of Rigidity (MOR), tensile strength capacity and its moisture contents were also determined. The deformation during testing was measured by means of mechanical extensometer. The MOE of the studied species range from 36.7 N/mm2 to 119.2 N/mm2, whereas Poisson’s ratio values show less variability. The result of the study also shows that the mechanical properties for the species are related. The larger the density value, the larger value of stress and strain will be. Thus, the value of Poisson ratio will also increase, respectively.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

scholarly journals First principles computation of composition dependent elastic constants of omega in titanium alloys: implications on mechanical behavior

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
R. Salloom ◽  
S. A. Mantri ◽  
R. Banerjee ◽  
S. G. Srinivasan
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
First Principles ◽  
Young's Modulus ◽  
Group Vi ◽  
Group V ◽  
Β Phase ◽  
Ti Alloys ◽  
Ω Phase ◽  
Stabilizer Concentration

AbstractFor decades the poor mechanical properties of Ti alloys were attributed to the intrinsic brittleness of the hexagonal ω-phase that has fewer than 5-independent slip systems. We contradict this conventional wisdom by coupling first-principles and cluster expansion calculations with experiments. We show that the elastic properties of the ω-phase can be systematically varied as a function of its composition to enhance both the ductility and strength of the Ti-alloy. Studies with five prototypical β-stabilizer solutes (Nb, Ta, V, Mo, and W) show that increasing β-stabilizer concentration destabilizes the ω-phase, in agreement with experiments. The Young’s modulus of ω-phase also decreased at larger concentration of β-stabilizers. Within the region of ω-phase stability, addition of Nb, Ta, and V (Group-V elements) decreased Young’s modulus more steeply compared to Mo and W (Group-VI elements) additions. The higher values of Young’s modulus of Ti–W and Ti–Mo binaries is related to the stronger stabilization of ω-phase due to the higher number of valence electrons. Density of states (DOS) calculations also revealed a stronger covalent bonding in the ω-phase compared to a metallic bonding in β-phase, and indicate that alloying is a promising route to enhance the ω-phase’s ductility. Overall, the mechanical properties of ω-phase predicted by our calculations agree well with the available experiments. Importantly, our study reveals that ω precipitates are not intrinsically embrittling and detrimental, and that we can create Ti-alloys with both good ductility and strength by tailoring ω precipitates' composition instead of completely eliminating them.

scholarly journals Tailoring a Low Young Modulus for a Beta Titanium Alloy by Combining Severe Plastic Deformation with Solution Treatment

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3467
Author(s):  
Anna Nocivin ◽  
Doina Raducanu ◽  
Bogdan Vasile ◽  
Corneliu Trisca-Rusu ◽  
Elisabeta Mirela Cojocaru ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Young Modulus ◽  
Orthopedic Implants ◽  
Beta Titanium Alloy

The present paper analyzed the microstructural characteristics and the mechanical properties of a Ti–Nb–Zr–Fe–O alloy of β-Ti type obtained by combining severe plastic deformation (SPD), for which the total reduction was of etot = 90%, with two variants of super-transus solution treatment (ST). The objective was to obtain a low Young’s modulus with sufficient high strength in purpose to use the alloy as a biomaterial for orthopedic implants. The microstructure analysis was conducted through X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) investigations. The analyzed mechanical properties reveal promising values for yield strength (YS) and ultimate tensile strength (UTS) of about 770 and 1100 MPa, respectively, with a low value of Young’s modulus of about 48–49 GPa. The conclusion is that satisfactory mechanical properties for this type of alloy can be obtained if considering a proper combination of SPD + ST parameters and a suitable content of β-stabilizing alloying elements, especially the Zr/Nb ratio.

scholarly journals Phase Formation, Microstructure and Mechanical Properties of Mg67Ag33 as Potential Biomaterial

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 461
Author(s):  
Konrad Kosiba ◽  
Konda Gokuldoss Prashanth ◽  
Sergio Scudino
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Equilibrium Phase ◽  
Antibacterial Properties ◽  
Equilibrium Phase Diagram ◽  
Compressive Yield Strength ◽  
X Ray ◽  
Fine Grained ◽  
Equilibrium Phases

The phase and microstructure formation as well as mechanical properties of the rapidly solidified Mg67Ag33 (at. %) alloy were investigated. Owing to kinetic constraints effective during rapid cooling, the formation of equilibrium phases is suppressed. Instead, the microstructure is mainly composed of oversaturated hexagonal closest packed Mg-based dendrites surrounded by a mixture of phases, as probed by X-ray diffraction, electron microscopy and energy dispersive X-ray spectroscopy. A possible non-equilibrium phase diagram is suggested. Mainly because of the fine-grained dendritic and interdendritic microstructure, the material shows appreciable mechanical properties, such as a compressive yield strength and Young’s modulus of 245 ± 5 MPa and 63 ± 2 GPa, respectively. Due to this low Young’s modulus, the Mg67Ag33 alloy has potential for usage as biomaterial and challenges ahead, such as biomechanical compatibility, biodegradability and antibacterial properties are outlined.

scholarly journals Effect of Nanopores on Mechanical Properties of the Shape Memory Alloy

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 529
Author(s):  
Chunzhi Du ◽  
Zhifan Li ◽  
Bingfei Liu
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Shape Memory ◽  
Young’S Modulus ◽  
Residual Strain ◽  
Surface Effect ◽  
Young's Modulus ◽  
Strain Curve ◽  
Stress Strain ◽  
Strength Limit

Nanoporous Shape Memory Alloys (SMA) are widely used in aerospace, military industry, medical and health and other fields. More and more attention has been paid to its mechanical properties. In particular, when the size of the pores is reduced to the nanometer level, the effect of the surface effect of the nanoporous material on the mechanical properties of the SMA will increase sharply, and the residual strain of the SMA material will change with the nanoporosity. In this work, the expression of Young’s modulus of nanopore SMA considering surface effects is first derived, which is a function of nanoporosity and nanopore size. Based on the obtained Young’s modulus, a constitutive model of nanoporous SMA considering residual strain is established. Then, the stress–strain curve of dense SMA based on the new constitutive model is drawn by numerical method. The results are in good agreement with the simulation results in the published literature. Finally, the stress-strain curves of SMA with different nanoporosities are drawn, and it is concluded that the Young’s modulus and strength limit decrease with the increase of nanoporosity.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

Sign in / Sign up

Export Citation Format

Share Document