scholarly journals Effect of Restorative Material on Mechanical Response of Provisional Endocrowns: A 3D—FEA Study

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 649
Author(s):  
João Paulo Mendes Tribst ◽  
Alexandre Luiz Souto Borges ◽  
Laís Regiane Silva-Concílio ◽  
Marco Antonio Bottino ◽  
Mutlu Özcan
Keyword(s):  
Stress Distribution ◽  
Mechanical Response ◽  
Resin Composite ◽  
Maximum Shear Stress ◽  
Acrylic Resin ◽  
Maximum Principal Stress ◽  
Dental Tissue ◽  
Element Analysis ◽  
Cement Layer ◽  
Restorative Materials

The goal of this study was to evaluate the stress distribution in an endocrown restoration according to different provisional restorative materials. An endodontically treated maxillary molar model was selected for conducting the finite element analysis (FEA), with a determined amount of dental remnant of 1.5 mm. The model was imported to the analysis software (ANSYS 19.2, ANSYS Inc., Houston, TX, USA) in STEP format. All contacts were considered perfectly bonded. The mechanical properties of each structure were considered isotropic, linear, elastic, and homogeneous. Three different provisional restorative materials were simulated (acrylic resin, bis-acrylic resin, and resin composite). An axial load (300 N) was applied at the occlusal surface in the center of the restoration. Results were determined by colorimetric stress maps of maximum principal stress, maximum shear stress, and total deformation. The different materials influenced the stress distribution for all structures; the higher the material’s elastic modulus, the lower the stress magnitude on the cement layer. In the present study, all provisional restorative materials showed similar stress patterns in the endocrown and on the cement layer however, with different magnitude. Based on this study limitation, the use of resin composite to manufacture provisional endocrowns is suggested as a promising material to reduce the stresses in the cement layer and in the dental tissue surfaces.

scholarly journals Mechanical Behavior of Different Restorative Materials and Onlay Preparation Designs in Endodontically Treated Molars

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1923
Author(s):  
Ana Beatriz Gomes de Carvalho ◽  
‪Guilherme Schmitt de Andrade ◽  
João Paulo Mendes Tribst ◽  
Elisa Donária Aboucauch Grassi ◽  
Pietro Ausiello ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Mechanical Behavior ◽  
Maximum Principal Stress ◽  
Element Analysis ◽  
Tooth Structure ◽  
Cement Layer ◽  
Restorative Materials ◽  
Homogeneous Stress

This study evaluated the effect of the combination of three different onlay preparation designs and two restorative materials on the stress distribution, using 3D-finite element analysis. Six models of first lower molars were created according to three preparation designs: non-retentive (nRET), traditional with occlusal isthmus reduction (IST), and traditional without occlusal isthmus reduction (wIST); and according to two restorative materials: lithium-disilicate (LD) and nanoceramic resin (NR). A 600 N axial load was applied at the central fossa. All solids were considered isotropic, homogeneous, and linearly elastic. A static linear analysis was performed, and the Maximum Principal Stress (MPS) criteria were used to evaluate the results and compare the stress in MPa on the restoration, cement layer, and tooth structure (enamel and dentin). A novel statistical approach was used for quantitative analysis of the finite element analysis results. On restoration and cement layer, nRET showed a more homogeneous stress distribution, while the highest stress peaks were calculated for LD onlays (restoration: 69–110; cement layer: 10.2–13.3). On the tooth structure, the material had more influence, with better results for LD (27–38). It can be concluded that nRET design showed the best mechanical behavior compared to IST and wIST, with LD being more advantageous for tooth structure and NR for the restoration and cement layer.

scholarly journals Influence of Polymeric Restorative Materials on the Stress Distribution in Posterior Fixed Partial Dentures: 3D Finite Element Analysis

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 758
Author(s):  
Larissa Mendes Campaner ◽  
Marcos Paulo Motta Silveira ◽  
Guilherme Schmitt de Andrade ◽  
Alexandre Luiz Souto Borges ◽  
Marco Antonio Bottino ◽  
...  
Keyword(s):  
Stress Distribution ◽  
Computer Aided Design ◽  
Resin Composite ◽  
Acrylic Resin ◽  
Element Analysis ◽  
Stress Criterion ◽  
Biomechanical Behavior ◽  
Computer Aided ◽  
Restorative Materials ◽  
Abutment Teeth

Background: This study evaluated the effect of interim restorative materials (acrylic resin (AR), resin composite (RC) or polyetheretherketone (PEEK) for dental computer-aided design/computer-aided manufacturing (CAD/CAM)) on the stress distribution of a posterior three-unit fixed partial denture. Methods: The abutment teeth (first molar and first premolar) were modeled using the BioCAD protocol containing 1.5 mm of axial reduction and converging axial walls. A static structural analysis was performed in the computer-aided engineering software, and the Maximum Principal Stress criterion was used to analyze the prosthesis and the cement layers of both abutment teeth. The materials were considered isotropic, linearly elastic, homogeneous and with bonded contacts. An axial load (600 N) was applied to the occlusal surface of the second premolar. Results: Regardless of the restorative material, the region of the prosthetic connectors showed the highest tensile stress magnitude. The highest stress peak was observed with the use of RC (129 MPa) compared to PEEK and AR. For the cement layers, RC showed the lowest values in the occlusal region (7 MPa) and the highest values for the cervical margin (14 MPa) compared to PEEK (21 and 12 MPa) and AR (21 and 13 MPa). Conclusions: Different interim restorative materials for posterior fixed partial dentures present different biomechanical behavior. The use of resin composite can attenuate the stress magnitude on the cement layer, and the use of acrylic resin can attenuate the stress magnitude on the connector region.

scholarly journals Comparative Stress Evaluation between Bilayer, Monolithic and Cutback All-Ceramic Crown Designs: 3D Finite Element Study

Prosthesis ◽  
2021 ◽  
Vol 3 (2) ◽  
pp. 173-180
Author(s):  
Nathália de Carvalho Ramos ◽  
Gabriela Freitas Ramos ◽  
Marcela Moreira Penteado ◽  
Renata Marques de Melo ◽  
Alexandre Luiz Souto Borges ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Maximum Principal Stress ◽  
Mechanical Analysis ◽  
Element Analysis ◽  
All Ceramic ◽  
Homogeneous Stress ◽  
Ceramic Crown

Different all-ceramic crown designs are available to perform indirect restoration; however, the mechanical response of each model should still be elucidated. The study aims to evaluate the stress distribution in three different zirconia crown designs using finite element analysis. Different three-dimensional molar crowns were simulated: conventional bilayer zirconia covered with porcelain, a monolithic full-contour zirconia crown, and the cutback modified zirconia crown with porcelain veneered buccal face. The models were imported to the computer-aided engineering (CAE) software. Tetrahedral elements were used to form the mesh and the mechanical properties were assumed as isotropic, linear and homogeneous materials. The contacts were considered ideal. For the static structural mechanical analysis, 100 N occlusal load was applied and the bone tissue was fixed. Maximum principal stress showed that the stress pattern was different for the three crown designs, and the traditional bilayer model showed higher stress magnitude comparing to the other models. However, grayscale stress maps showed homogeneous stress distribution for all models. The all-ceramic crown designs affect the stress distribution, and the cutback porcelain-veneered zirconia crown can be a viable alternative to adequate function and esthetic when the monolithic zirconia crown cannot be indicated.

scholarly journals Folding photopolymerized origami sheets by post-curing

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Xiaodong He ◽  
Christopher-Denny Matte ◽  
Tsz-Ho Kwok
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Maximum Principal Stress ◽  
Second Step ◽  
Post Processing ◽  
Element Analysis ◽  
Digital Light Processing ◽  
Processing Step ◽  
Lower Maximum

AbstractThe paper presents a novel manufacturing approach to fabricate origami based on 3D printing utilizing digital light processing. Specifically, we propose to leave part of the model uncured during the printing step, and then cure it in the post-processing step to set the shape in a folded configuration. While the cured regions in the first step try to regain their unfolded shape, the regions cured in the second step attempt to keep their folded shape. As a result, the final shape is obtained when both regions’ stresses reach equilibrium. Finite element analysis is performed in ANSYS to obtain the stress distribution on common hinge designs, demonstrating that the square-hinge has a lower maximum principal stress than elliptical and triangle hinges. Based on the square-hinge and rectangular cavity, two variables—the hinge width and the cavity height—are selected as principal variables to construct an empirical model with the final folding angle. In the end, experimental verification shows that the developed method is valid and reliable to realize the proposed deformation and 3D development of 2D hinges.

Finite Element Analysis and Investigation of Double-Row Piles Supporting Structure

2013 ◽  
Vol 838-841 ◽  
pp. 779-785
Author(s):  
Liang Gu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Maximum Shear Stress ◽  
Horizontal Displacement ◽  
Deep Foundation ◽  
Foundation Pit ◽  
Double Row ◽  
Element Analysis ◽  
Supporting Structure

The double-row piles supporting structure is a new type of supporting and protecting for deep foundation excavation. It is widely used to in design of deep foundation pit. Now how to simply and effectively design the structure of double-row piles is in a research and discuss stage. Using the Midas GTS finite element method, the displacement and stress distribution of double-row piles in the different stages of excavation are obtained, and the horizontal displacement and stress distribution of double-row piles in the different stages of excavation are calculated. The results of Midas GTS finite element analysis as follows: (1) after the excavation of foundation pit, the horizontal displacement of pile-top is maximum. The horizontal displacement decreases gradually with depth increases. And the displacement of front row piles is larger than that of back row piles; (2) the maximum shear stress is at the distance 5m to the foundation basement. The higher bending moment at the pile-top and the distance 10m to the foundation basement are consistent with the actual monitoring date. (3) the results of finite element analysis is close to the Richard software and actual monitoring data. It is show that using the finite element analysis to analyze the double-row piles supporting structure with is veritable and credible.

scholarly journals Influence of fibromucosa height and loading on the stress distribution of a total prosthesis: a finite element analysis

2021 ◽  
Vol 24 (2) ◽  
Author(s):  
Tarcisio José de Arruda Paes Junior ◽  
João Paulo Mendes Tribst ◽  
Amanda Maria de Oliveira Dal Piva ◽  
Viviane Maria Gonçalves de Figueiredo ◽  
Alexandre Luiz Souto Borges ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Cortical Bone ◽  
Principal Stress ◽  
Maximum Principal Stress ◽  
Element Analysis ◽  
Total Displacement ◽  
Anterior Guidance ◽  
Mandibular Movements

Purpose: To evaluate the effect of fibromucosa height on the stress distribution and displacement of mandibular total prostheses during posterior unilateral load, posterior bilateral load and anterior guidance using the finite element analysis (FEA). Material and methods: 3D virtual models were made to simulate the stress generated during different mandibular movements in a total prosthesis. The contacts were simulated according to the physiology, being considered perfectly bonded between cortical and medullar bones; and between cortical bone and mucosa. Non-linear frictional contact was used for the total prosthesis base and fibromucosa, allowing the prosthesis to slide over the tissue. The cortical bone base was fixed and the 100 N load was applied as unilateral load, posterior bilateral load and anterior guidance simulation. The required results were for maximum principal stress (MPa), microstrain (mm/mm) and total displacement (mm). The numerical results were converted into colorimetric maps and arranged according to corresponding scales. Results: The stress generated in all situations was directly proportional to the fibromucosa height. The maximum principal stress results demonstrated greater magnitude for anterior guidance, posterior unilateral and posterior bilateral, respectively. Only posterior unilateral load demonstrated an increase in bone microstrain, regardless of the fibromucosa height. Prosthesis displacement was lower under posterior bilateral loading. Conclusion: Posterior bilateral loading is indicated for total prosthesis because it allows lower prosthesis displacement, lower stress concentration at the base of the prosthesis and less bone microstrain.   Keywords Finite element analysis; Occlusion; Total prosthesis.

scholarly journals Effect of Fiber Posts on Stress Distribution of Endodontically Treated Upper Premolars: Finite Element Analysis

Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1708 ◽  
Author(s):  
Maciej Zarow ◽  
Mirco Vadini ◽  
Agnieszka Chojnacka-Brozek ◽  
Katarzyna Szczeklik ◽  
Grzegorz Milewski ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Resin Composite ◽  
Von Mises Stress ◽  
Stress Distributions ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Endodontically Treated Tooth ◽  
Maxillary Premolars ◽  
Von Mises

By means of a finite element method (FEM), the present study evaluated the effect of fiber post (FP) placement on the stress distribution occurring in endodontically treated upper first premolars (UFPs) with mesial–occlusal–distal (MOD) nanohybrid composite restorations under subcritical static load. FEM models were created to simulate four different clinical situations involving endodontically treated UFPs with MOD cavities restored with one of the following: composite resin; composite and one FP in the palatal root; composite and one FP in the buccal root; or composite and two FPs. As control, the model of an intact UFP was included. A simulated load of 150 N was applied. Stress distribution was observed on each model surface, on the mid buccal–palatal plane, and on two horizontal planes (at cervical and root-furcation levels); the maximum Von Mises stress values were calculated. All analyses were replicated three times, using the mechanical parameters from three different nanohybrid resin composite restorative materials. In the presence of FPs, the maximum stress values recorded on dentin (in cervical and root-furcation areas) appeared slightly reduced, compared to the endodontically treated tooth restored with no post; in the same areas, the overall Von Mises maps revealed more favorable stress distributions. FPs in maxillary premolars with MOD cavities can lead to a positive redistribution of potentially dangerous stress concentrations away from the cervical and the root-furcation dentin.

Axisymmetric Finite Element Analysis of Hip Replacement with an Elastomeric Layer: The Effects of Layer Thickness

1994 ◽  
Vol 208 (3) ◽  
pp. 139-149 ◽  
Author(s):  
A Strozzi ◽  
A Unsworth
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Mechanical Response ◽  
Maximum Shear Stress ◽  
Hydrodynamic Theory ◽  
Asymptotic Model ◽  
Hip Joints ◽  
Element Analysis ◽  
Contact Width ◽  
Artificial Hip Joints

Finite element analysis of compliant layered artificial hip joints has been used to study the mechanical response of four different layer thicknesses from 0.5 to 3 mm. The results have been compared with a classical asymptotic model in terms of maximum contact pressure and contact width, and of maximum shear stress at the layer-backing interface and its location. The surface deformations and load capacities have also been compared. The best thickness was found to be 2 mm; though a marginal reduction in stresses would be found in the 3 mm layer, the penetrations would be greater and these might have implications for the fatigue life of the material. A formula for the thickness of the fluid film has been derived on the basis of the inverse hydrodynamic theory and the results show good correlation with existing theories.

Finite Element Analysis of Provisional Structures of Implant-Supported Complete Prostheses

2014 ◽  
Vol 40 (2) ◽  
pp. 161-168 ◽  
Author(s):  
Bruno Albuquerque Carneiro ◽  
Rui Barbosa de Brito ◽  
Fabiana Mantovani Gomes França
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Axial Loading ◽  
Acrylic Resin ◽  
Safe Procedure ◽  
Element Analysis ◽  
Posterior Teeth ◽  
Occlusal Surfaces ◽  
Three Dimensional Finite Element

The use of provisional resin implant-supported complete dentures is a fast and safe procedure to restore mastication and esthetics of patients soon after surgery and during the adaptation phase to the new denture. This study assessed stress distribution of provisional implant-supported fixed dentures and the all-on-4 concept using self-curing acrylic resin (Tempron) and bis-acrylic resin (Luxatemp) to simulate functional loads through the three-dimensional finite element method. Solidworks software was used to build three-dimensional models using acrylic resin (Tempron, model A) and bis-acrylic resin (Luxatemp, model B) for denture captions. Two loading patterns were applied on each model: (1) right unilateral axial loading of 150 N on the occlusal surfaces of posterior teeth and (2) oblique loading vector of 150 N at 45°. The results showed that higher stress was found on the bone crest below oblique load application with a maximum value of 187.57 MPa on model A and 167.45 MPa on model B. It was concluded that model B improved stress distribution on the denture compared with model A.

Sign in / Sign up

Export Citation Format

Share Document