scholarly journals Experimental Investigation of the Pumping of a Model-Concrete through Pipes

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1161
Author(s):  
Martin A. Haustein ◽  
Moritz N. Kluwe ◽  
Rüdiger Schwarze
Keyword(s):  
Pressure Loss ◽  
Plug Flow ◽  
Particle Migration ◽  
Test Plant ◽  
Flow Profile ◽  
Time Resolved ◽  
Rheological Measurements ◽  
Lubricating Layer ◽  
Image Velocimetry ◽  
First Time

Many practical aspects of processing fresh concrete depend on its rheology, such as the pumping of the material. It is known that a lubricating layer is formed in the process, which significantly reduces the pumping pressure. However, these phenomena can hardly be considered in the usual rheological measurements. A main problem is the optical inaccessibility of the material, which prevents estimations about, e.g., the thickness of the plug flow or particle migration. In this paper, the pneumatic pumping of a transparent model concrete is performed by means of a test plant. The flow profile over the entire pipe cross-section is resolved in time and space via Particle Image Velocimetry (PIV) measurements. This allows the comparison with the analytical flow profile from rheological measurements of the material using the Buckingham–Reiner equation. A reduction of the pressure loss to around 60% induced through segregation of the material is found. These measurements reflect the rheology of the material under realistic pumping conditions including particle migration. This makes it possible for the first time to observe a transparent material with concrete-like rheology under pulsating pumping conditions and to compare the true and calculated time-resolved pressure loss.

Spatio-Temporal Development of Supercavitation Over an Impulsively Launched Projectile

2006 ◽  
Author(s):  
C. J. Weiland ◽  
P. P. Vlachos
Keyword(s):  
High Speed ◽  
Temporal Development ◽  
Two Phase ◽  
Time Resolved ◽  
Gas Gun ◽  
Supercavitating Flow ◽  
Image Velocimetry ◽  
Spatio Temporal ◽  
Asymmetric Vortices ◽  
First Time

Supercavitation inception and formation was studied over blunt projectiles. The projectiles were fired using a gas gun method. In this method, projectiles are launched under the action of expanding detonation gases. Both qualitative and quantitative optical flow diagnostics using high speed digital imaging were used to analyze the spatio-temporal development of the supercavitating flow. For the first time, quantification of the supercavitation was achieved using Time Resolved Digital Particle Image Velocimetry (TRDPIV) detailing the two phase flow field surrounding the translating projectiles and the gas vapor bubble. Experimental results indicate that the supercavity forms at the aft end of the projectile and travels forward along the direction of projectile travel. The impulsive start of the projectile generates two asymmetric vortices which are shed from the blunt nose of the projectile. The vortices interact with the moving cavity and subsequently deform. This interaction is believed to directly contribute to the instabilities in the flight path.

scholarly journals Time-resolved particle image velocimetry measurements of the turbulent Richtmyer–Meshkov instability

2021 ◽  
Vol 917 ◽  
Author(s):  
Everest G. Sewell ◽  
Kevin J. Ferguson ◽  
Vitaliy V. Krivets ◽  
Jeffrey W. Jacobs
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Time Resolved ◽  
Image Velocimetry

Abstract

Visualization and Time-Resolved Particle Image Velocimetry Measurements of the Flow in the Tip Region of a Subsonic Compressor Rotor

2014 ◽  
Vol 137 (4) ◽  
Author(s):  
David Tan ◽  
Yuanchao Li ◽  
Ian Wilkes ◽  
Rinaldo L. Miorini ◽  
Joseph Katz
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Axial Compressor ◽  
Time Resolved ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Direct Measurements ◽  
Image Velocimetry ◽  
The One ◽  
And Behavior

A new optically index matched facility has been constructed to investigate tip flows in compressor-like settings. The blades of the one and a half stage compressor have the same geometry, but lower aspect ratio as the inlet guide vanes (IGVs) and the first stage of the low-speed axial compressor (LSAC) facility at NASA Glenn. With transparent blades and casings, the new setup enables unobstructed velocity measurements at any point within the tip region and is designed to facilitate direct measurements of effects of casing treatments on the flow structure. We start with a smooth endwall casing. High speed movies of cavitation and time-resolved PIV measurements have been used to characterize the location, trajectory, and behavior of the tip leakage vortex (TLV) for two flow rates, the lower one representing prestall conditions. Results of both methods show consistent trends. As the flow rate is reduced, TLV rollup occurs further upstream, and its initial orientation becomes more circumferential. At prestall conditions, the TLV is initially aligned slightly upstream of the rotor passage, and subsequently forced downstream. Within the passage, the TLV breaks up into a large number of vortex fragments, which occupy a broad area. Consequently, the cavitation in the TLV core disappears. With decreasing flow rate, this phenomenon becomes more abrupt, occurs further upstream, and the fragments occupy a larger area.

Time-Resolved Particle Image Velocimetry (PIV) Measurements in a Radial Diffuser Pump

2009 ◽  
Author(s):  
Jianjun Feng ◽  
Friedrich-Karl Benra ◽  
Hans Josef Dohmen
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Time Resolved ◽  
Piv Measurements ◽  
Part Load ◽  
Channel Characteristic ◽  
Image Velocimetry ◽  
Pump Stage ◽  
Low Specific Speed ◽  
Load Conditions

The truly time-variant unsteady flow in a low specific speed radial diffuser pump stage has been investigated by time-resolved Particle Image Velocimetry (PIV) measurements. The measurements are conducted at the midspan of the blades for the design condition and also for some severe part-load conditions. The instantaneous flow fields among different impeller channels are analyzed and compared in detail, and more attention has been paid to flow separations at part-load conditions. The analysis of the measured results shows that the flow separations at two adjacent impeller channels are quite different at some part-load conditions. The separations generally exhibit a two-channel characteristic.

Time-Resolved DPIV Analysis of Vortex Dynamics in a Left Ventricular Model Through Bileaflet Mechanical and Porcine Heart Valve Prostheses

2004 ◽  
Vol 126 (6) ◽  
pp. 714-726 ◽  
Author(s):  
Olga Pierrakos ◽  
Pavlos P. Vlachos ◽  
Demetri P. Telionis
Keyword(s):  
Mitral Valve ◽  
Vortex Formation ◽  
Flow Patterns ◽  
Left Ventricular ◽  
Time Resolved ◽  
Vortical Structures ◽  
Jude Medical ◽  
Image Velocimetry ◽  
Valve Prostheses ◽  
Physical Phenomena

The performance of the heart after a mitral valve replacement operation greatly depends on the flow character downstream of the valve. The design and implanting orientation of valves may considerably affect the flow development. A study of the hemodynamics of two orientations, anatomical and anti-anatomical, of the St. Jude Medical (SJM) bileaflet valve are presented and compared with those of the SJM Biocor porcine valve, which served also to represent the natural valve. We document the velocity field in a flexible, transparent (LV) using time-resolved digital particle image velocimetry (TRDPIV). Vortex formation and vortex interaction are two important physical phenomena that dominate the filling and emptying of the ventricle. For the three configurations, the following effects were examined: mitral valve inlet jet asymmetry, survival of vortical structures upstream of the aortic valve, vortex-induced velocities and redirection of the flow in abidance of the Biot–Savart law, domain segmentation, resonant times of vortical structures, and regions of stagnant flow. The presence of three distinct flow patterns, for the three configurations, was identified by the location of vortical structures and level of coherence corresponding to a significant variation in the turbulence level distribution inside the LV. The adverse effect of these observations could potentially compromise the efficiency of the LV and result in flow patterns that deviate from those in the natural heart.

Entrainment and topology of accelerating shear layers

2016 ◽  
Vol 811 ◽  
pp. 37-50 ◽  
Author(s):  
Giuseppe A. Rosi ◽  
David E. Rival
Keyword(s):  
Shear Layer ◽  
Particle Image ◽  
Point Vortex ◽  
Reynolds Numbers ◽  
Shear Layers ◽  
Circular Path ◽  
Entrainment Rate ◽  
Time Resolved ◽  
And Topology ◽  
Image Velocimetry

A constantly accelerating circular plate was investigated towards understanding the effect of non-stationarity on shear-layer entrainment and topology. Dye visualizations and time-resolved particle image velocimetry measurements were collected for normalized accelerations spanning three orders of magnitude. Increasing acceleration acts to organize shear-layer topology. Specifically, the Kelvin–Helmholtz instabilities within the shear layer better adhered to a circular path and exhibited consistent and repeatable spacing. Normalized starting-vortex circulation was observed to collapse with increasing acceleration, which one might not expect due to increased levels of mixing at higher instantaneous Reynolds numbers. The entrainment rate was shown to increase nonlinearly with increasing acceleration. This was attributed to closer spacing between instabilities, which better facilitates the roll-up of fluid between the shear layer and vortex core. The shear-layer organization observed at higher accelerations was associated with smaller spacings between instabilities. Specifically, analogous point-vortex simulations demonstrated that decreasing the spacing between instabilities acts to localize and dampen perturbations within an accelerating shear layer.

Sign in / Sign up

Export Citation Format

Share Document