scholarly journals Nanowire Ring Embedded in a Flexible Substrate for Local Strain Detection

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 347
Author(s):  
Shengkun Li ◽  
Yue Qin ◽  
Xin Li ◽  
Yuejin Zhao
Keyword(s):  
Detection System ◽  
Structural Parameters ◽  
Flexible Substrate ◽  
Ring Cavity ◽  
Local Strain ◽  
Strain Sensors ◽  
Resonant Wavelength ◽  
Gauge Factor ◽  
Light Sources ◽  
End To End

Optical sensing has attracted more and more attention in recent years with the advance in planar waveguide fabrication processes. The photon, as a carrier of information in sensing areas, could have a better performance than electrons. We propose a novel end-to-end ring cavity to fabricate sensitive units of a strain sensor. We then propose a method of combining a flexible substrate with an end-to-end semiconductor nanowire ring cavity to fabricate novel strain sensors. We used a tuning resonant wavelength detected by a homebuilt excitation and detection system to measure applied strain. The resonant wavelength of the strain gauge was red-shift and linear tuned with increasing strain. The gauge factor was about 50, calculated through experiments and theory, and Q was 1938, with structural parameters L = 70 µm and d = 1 µm. The high sensitivity makes it possible to measure micro deformation more accurately. End-to-end coupling active nanowire waveguides eliminate the shortcomings of side by side coupling structures, which have the phasing shift with no minor optical density loss. This resonator in flexible substrates could be used not only as on-chip strain sensors for micro or nano deformation detecting but also as tunable light sources for photonic integrated circuits.

2D end-to-end carbon nanotube conductive networks in polymer nanocomposites: a conceptual design to dramatically enhance the sensitivities of strain sensors

Nanoscale ◽  
2018 ◽  
Vol 10 (5) ◽  
pp. 2191-2198 ◽  
Author(s):  
Jun-Hong Pu ◽  
Xiang-Jun Zha ◽  
Min Zhao ◽  
Shengyao Li ◽  
Rui-Ying Bao ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Polymer Nanocomposites ◽  
Conceptual Design ◽  
Strain Sensor ◽  
Small Strain ◽  
Strain Sensors ◽  
Sensitive Strain ◽  
Gauge Factor ◽  
Highly Sensitive ◽  
End To End

A highly sensitive strain sensor with end-to-end CNT networks and showing a high gauge factor (248) at small strain (5%) is fabricated.

scholarly journals Concentric Array of Printed Strain Sensors for Structural Health Monitoring

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 1997 ◽  
Author(s):  
Daniel Zymelka ◽  
Kazuyoshi Togashi ◽  
Takeshi Kobayashi
Keyword(s):  
Sensor Array ◽  
Crack Formation ◽  
Flexible Substrate ◽  
Local Strain ◽  
Strain Sensors ◽  
Civil Infrastructure ◽  
Civil Structures ◽  
Sensing Systems ◽  
Potential Applications ◽  
Crack Tips

Civil infrastructure is expanding around the world. The ever-growing trend toward urbanization drives the demand for new investments. However, the new constructions and gradual deterioration of those already existing, especially bridges, give rise to concerns about their proper maintenance. To improve safety and drive down maintenance costs of civil structures, there is a need for inexpensive sensing systems capable of reliable and automated monitoring. In this study, we present a new concept of thin-film strain sensors arranged in an array with a concentric layout that is incorporated into a flexible substrate sheet. The designed sensor array is intended to analyze strains in the proximity of round holes made at the crack tips, found in the investigated construction elements of civil structures. In this study, the performance of the sensor array was demonstrated using measurements taken on a highway bridge in one of the largest cities in Japan. We show that it can measure local strain distribution and indicate a region with risk for crack formation. The demonstrated results show new area of potential applications for the printed strain sensors in monitoring civil structures.

scholarly journals Development of Highly Sensitive Strain Sensor Using Area-Arrayed Graphene Nanoribbons

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1701
Author(s):  
Ken Suzuki ◽  
Ryohei Nakagawa ◽  
Qinqiang Zhang ◽  
Hideo Miura
Keyword(s):  
Graphene Nanoribbons ◽  
Strain Sensor ◽  
Strain Sensors ◽  
Sensitive Strain ◽  
Bending Test ◽  
Gauge Factor ◽  
Four Point Bending ◽  
Current Voltage ◽  
Highly Sensitive ◽  
Current Voltage Relationship

In this study, a basic design of area-arrayed graphene nanoribbon (GNR) strain sensors was proposed to realize the next generation of strain sensors. To fabricate the area-arrayed GNRs, a top-down approach was employed, in which GNRs were cut out from a large graphene sheet using an electron beam lithography technique. GNRs with widths of 400 nm, 300 nm, 200 nm, and 50 nm were fabricated, and their current-voltage characteristics were evaluated. The current values of GNRs with widths of 200 nm and above increased linearly with increasing applied voltage, indicating that these GNRs were metallic conductors and a good ohmic junction was formed between graphene and the electrode. There were two types of GNRs with a width of 50 nm, one with a linear current–voltage relationship and the other with a nonlinear one. We evaluated the strain sensitivity of the 50 nm GNR exhibiting metallic conduction by applying a four-point bending test, and found that the gauge factor of this GNR was about 50. Thus, GNRs with a width of about 50 nm can be used to realize a highly sensitive strain sensor.

scholarly journals Giant gauge factor of Van der Waals material based strain sensors

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Wenjie Yan ◽  
Huei-Ru Fuh ◽  
Yanhui Lv ◽  
Ke-Qiu Chen ◽  
Tsung-Yin Tsai ◽  
...  
Keyword(s):  
Carrier Mobility ◽  
Large Range ◽  
Van Der Waals ◽  
High Sensitivity ◽  
Strain Sensors ◽  
Strain Gauges ◽  
Gauge Factor ◽  
Proof Of Concept ◽  
High Flexibility ◽  
Small Deformations

AbstractThere is an emergent demand for high-flexibility, high-sensitivity and low-power strain gauges capable of sensing small deformations and vibrations in extreme conditions. Enhancing the gauge factor remains one of the greatest challenges for strain sensors. This is typically limited to below 300 and set when the sensor is fabricated. We report a strategy to tune and enhance the gauge factor of strain sensors based on Van der Waals materials by tuning the carrier mobility and concentration through an interplay of piezoelectric and photoelectric effects. For a SnS2 sensor we report a gauge factor up to 3933, and the ability to tune it over a large range, from 23 to 3933. Results from SnS2, GaSe, GeSe, monolayer WSe2, and monolayer MoSe2 sensors suggest that this is a universal phenomenon for Van der Waals semiconductors. We also provide proof of concept demonstrations by detecting vibrations caused by sound and capturing body movements.

scholarly journals Anisotropic, Wrinkled, and Crack-Bridging Structure for Ultrasensitive, Highly Selective Multidirectional Strain Sensors

2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Heng Zhang ◽  
Dan Liu ◽  
Jeng-Hun Lee ◽  
Haomin Chen ◽  
Eunyoung Kim ◽  
...  
Keyword(s):  
Rational Design ◽  
Full Range ◽  
Human Motion ◽  
Strain Sensors ◽  
Gauge Factor ◽  
Wearable Electronics ◽  
Trade Off ◽  
Human Motion Detection ◽  
Sensing Applications ◽  
Anisotropic Structures

AbstractFlexible multidirectional strain sensors are crucial to accurately determining the complex strain states involved in emerging sensing applications. Although considerable efforts have been made to construct anisotropic structures for improved selective sensing capabilities, existing anisotropic sensors suffer from a trade-off between high sensitivity and high stretchability with acceptable linearity. Here, an ultrasensitive, highly selective multidirectional sensor is developed by rational design of functionally different anisotropic layers. The bilayer sensor consists of an aligned carbon nanotube (CNT) array assembled on top of a periodically wrinkled and cracked CNT–graphene oxide film. The transversely aligned CNT layer bridge the underlying longitudinal microcracks to effectively discourage their propagation even when highly stretched, leading to superior sensitivity with a gauge factor of 287.6 across a broad linear working range of up to 100% strain. The wrinkles generated through a pre-straining/releasing routine in the direction transverse to CNT alignment is responsible for exceptional selectivity of 6.3, to the benefit of accurate detection of loading directions by the multidirectional sensor. This work proposes a unique approach to leveraging the inherent merits of two cross-influential anisotropic structures to resolve the trade-off among sensitivity, selectivity, and stretchability, demonstrating promising applications in full-range, multi-axis human motion detection for wearable electronics and smart robotics.

scholarly journals A Novel Textile Stitch-Based Strain Sensor for Wearable End Users

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1469 ◽  
Author(s):  
Orathai Tangsirinaruenart ◽  
George Stylios
Keyword(s):  
Mechanical Properties ◽  
Electrical Resistance ◽  
Body Movement ◽  
Strain Sensor ◽  
Strain Sensors ◽  
Gauge Factor ◽  
Heart Monitoring ◽  
Textile Sensors ◽  
Good Repeatability ◽  
The Ideal

This research presents an investigation of novel textile-based strain sensors and evaluates their performance. The electrical resistance and mechanical properties of seven different textile sensors were measured. The sensors are made up of a conductive thread, composed of silver plated nylon 117/17 2-ply, 33 tex and 234/34 4-ply, 92 tex and formed in different stitch structures (304, 406, 506, 605), and sewn directly onto a knit fabric substrate (4.44 tex/2 ply, with 2.22, 4.44 and 7.78 tex spandex and 7.78 tex/2 ply, with 2.22 and 4.44 tex spandex). Analysis of the effects of elongation with respect to resistance indicated the ideal configuration for electrical properties, especially electrical sensitivity and repeatability. The optimum linear working range of the sensor with minimal hysteresis was found, and the sensor’s gauge factor indicated that the sensitivity of the sensor varied significantly with repeating cycles. The electrical resistance of the various stitch structures changed significantly, while the amount of drift remained negligible. Stitch 304 2-ply was found to be the most suitable for strain movement. This sensor has a wide working range, well past 50%, and linearity (R2 is 0.984), low hysteresis (6.25% ΔR), good gauge factor (1.61), and baseline resistance (125 Ω), as well as good repeatability (drift in R2 is −0.0073). The stitch-based sensor developed in this research is expected to find applications in garments as wearables for physiological wellbeing monitoring such as body movement, heart monitoring, and limb articulation measurement.

scholarly journals Microscale local strain gauges based on visible micro-disk lasers embedded in a flexible substrate

2018 ◽  
Vol 26 (13) ◽  
pp. 16797 ◽  
Author(s):  
Taojie Zhou ◽  
Jie Zhou ◽  
Yuzhou Cui ◽  
Xiu Liu ◽  
Jiagen Li ◽  
...  
Keyword(s):  
Flexible Substrate ◽  
Local Strain ◽  
Strain Gauges

Cantilever enhanced based photoacoustic detection of SF6 decomposition component SO2 using UV LED

Sensor Review ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Tunan Chen ◽  
Fengxiang Ma ◽  
Yue Zhao ◽  
Zhenghai Liao ◽  
Zongjia Qiu ◽  
...  
Keyword(s):  
Detection Limit ◽  
Detection System ◽  
Light Sources ◽  
Photoacoustic Detection ◽  
Low Light ◽  
Power Requirement ◽  
Light Power ◽  
Content Type ◽  
Uv Led ◽  
Sf6 Decomposition

Purpose This paper aims to establish a photoacoustic detection system for SO2 using UV-LED and testify its feasibility for sensitive measurement. The work in this paper can avoid potential crossover interference in infrared (IR) range and also balance the capability and cost of feasible excitation for photoacoustic detection system. Design/methodology/approach In this experimental work, a cantilever-enhanced–based photoacoustic SO2 detection system using an ultraviolet (UV) LED light source with a light power of 4 mW as the excitation was established. Findings A feasible photoacoustic detection system for SO2 using UV-LED was established. Experimental results demonstrate that the detection limit of the system can reach the level of 0.667 ppm, which can serve as a reference for the application of PAS in insulation fault diagnosis. Originality/value This work investigated the potential of using ultraviolet photoacoustic spectroscopy to detect trace SO2, which provided an ideal replacement of infrared-laser-based detection system. In this paper, a photoacoustic detection system using LED with a low light power was established. Low light power requirement can expand the options of light sources accordingly. In this paper, the absorption characteristics of SO2 in the presented detection system and ultraviolet range were studied. And the detection limit of the presented system was given. Both of which can provide reference to SO2 detection in ambient SF6.

scholarly journals A novel strain sensor using a microchannel embedded in PDMS

2018 ◽  
Vol 4 (2) ◽  
pp. 1 ◽  
Author(s):  
Angelica Campigotto ◽  
Stephane Leahy ◽  
Ayan Choudhury ◽  
Guowei Zhao ◽  
Yongjun Lai
Keyword(s):  
Finite Element ◽  
Rotation Angle ◽  
Strain Sensor ◽  
Element Model ◽  
Strain Sensors ◽  
Gauge Factor ◽  
Sectional Area ◽  
Cross Sectional ◽  
Higher Sensitivity

A novel, inexpensive, and easy-to-use strain sensor using polydimethylsiloxane (PDMS)  was developed. The sensor consists of a microchannel that is partially filled with a coloured liquid and embedded in a piece of PDMS. A finite element model was developed to optimize the geometry of the microchannel to achieve higher sensitivity. The highest gauge factor that was measured experimentally was 41. The gauge factor was affected by the microchannel’s square cross-sectional area, the number of basic units in the microchannel, and the inlet and outlet configuration. As a case study, the developed strain sensors were used to measure the rotation angle of the wrist and finger joints.

Sign in / Sign up

Export Citation Format

Share Document